AKRON POPULAR and CONTINENTAL Models 9220 series User Manuals Oct 2000

AKRON 9221A, 9221B, 9221C, 9222A, 9222B, 9222C, 9231A, 9231B, 9231C, 9232A, 9232B, 9232C

Contents 1.

Introduction

2

Warnings, Cautions General Warnings

2 2

2.

Installation

3

3.

Operation

4 5 6

4.

Accessories – Operating Instructions

7

Cot Sides Paper Roll Holder Gynae Stirrups Gynae Troughs Cyriax Horns Arm Support Hole & Horn Lean Back Frame Fixation Rails

7 7 7 8 8 8 9 9 9

5.

Cleaning and Decontamination

10

6.

Troubleshooting

11

7.

Maintenance

11

8.

Warranty and Service

12 13

9.

Revision Status

13

10.

Technical Specification

14 15 16

"The

mark on this product demonstrates conformity with the EC Directive 93/42/EEC."

1

AKRON 9221A, 9221B, 9221C, 9222A, 9222B, 9222C, 9231A, 9231B, 9231C, 9232A, 9232B, 9232C

1. Introduction Always keep this Operating Manual available for reference.

Warnings & Cautions WARNINGS Warnings identify possible hazards in procedures or conditions which, if not correctly followed, could result in death, injury or other serious adverse reactions.

CAUTIONS Cautions identify conditions or procedures which, if not correctly followed, could result in equipment failure or damage.

General Warnings WARNINGS Use only accessories that have been designed or approved for use with this couch. Do not use electric couches in the presence of flammable gasses such as an anaesthetic agent. Maximum Load 180 Kg (396 lbs) distributed evenly. Do not concentrate weight on either side of the couch. Plug acts as a disconnect device. Do not allow children to play with the couch at any time. Adequately supervise children in the proximity of the couch.

2

AKRON 9221A, 9221B, 9221C, 9222A, 9222B, 9222C, 9231A, 9231B, 9231C, 9232A, 9232B, 9232C

2. Installation Adjustable Foot WARNING Lock castors before adjusting.

A)

Lock castors first.

B)

Adjust foot.

C)

Lock foot by tightening half nut.

WARNING Do not insert the 2-pin mains connector directly into a 3-pin 13A mains outlet. Always use the adapter provided. Plug acts as a disconnect device. Electric Models Use adapter if 3 pin 13A plug is required. (Order reference 5S0409Z)

Ensure mains supply cable is not stretched when connected. Ensure, during couch use, no obstacles are in its path. Ensure hand / foot switch tubes or leads are not trapped by moving parts of the couch.

CAUTION When not in use, switch couch off.

3

AKRON 9221A, 9221B, 9221C, 9222A, 9222B, 9222C, 9231A, 9231B, 9231C, 9232A, 9232B, 9232C

3. Operation Elevation Controls WARNING Safely position patient before elevating couch. Position all electrical cables away from the moving parts. Position Hand/Foot switch where accidental operation is not possible. Hydraulic Models

PUMP PEDAL TO RAISE COUCH

Hydraulic Pedal

Electric Models

Press é to raise couch. Press ê to lower couch.

Handswitch

AUF

Press é to raise couch AB

Press ê to lower couch. Footswitch

4

LIFT PEDAL TO LOWER COUCH

AKRON 9221A, 9221B, 9221C, 9222A, 9222B, 9222C, 9231A, 9231B, 9231C, 9232A, 9232B, 9232C

3. Operation Foot Bar Switch

Press tube done to raise couch Lift tube up to lower couch

Wheel Locking WARNING Lock couch wheels/castors prior to patient transfer or treatment. The retractable castors are not designed for transportation of patients. Disconnect and coil electrical cord away from moving parts prior to repositioning couch. Castors

Castors Unlocked

Castors Locked

Breathing Hole and Plug

Remove plug for patient prone position. Press out from underneath.

5

AKRON 9221A, 9221B, 9221C, 9222A, 9222B, 9222C, 9231A, 9231B, 9231C, 9232A, 9232B, 9232C

3. Operation Head & Foot Sections CAUTION Support upholstery section while manually altering the angle.

A & B Type Head Section Operating Lever A)

Press lever UP to alter section angle.

B)

Support section when altering angle.

C)

Release lever to lock section in position. Angles A Type = +80° -20° B Type = +45° -20°

C Type Head Section Operating Lever A)

Press lever UP to alter section angle.

B)

Support section when altering angle.

C)

Release lever to lock section in position. Angles C Type = +45° -20°

Foot Section Operating Lever A)

Press lever UP to alter section angle.

B)

Support section when altering angle.

C)

Release lever to lock section in position. Foot Section Angles = +80° -0°

C Type Head Section Arm Rests A)

Tilt Armrest towards Head Section.

B)

Move Armrest into position.

C)

Release Armrest to lock into position.

6

AKRON 9221A, 9221B, 9221C, 9222A, 9222B, 9222C, 9231A, 9231B, 9231C, 9232A, 9232B, 9232C

4. Accessories – Operating Instructions Cot Sides

Raised Cot Side

Lowered Cot Side

1.

To raise the cot side when in the down position, lift and rotate towards you, through 180°. Once upright, push the cot side downwards into the moulded block until located fully.

2.

To lower the cot side from upright position, lift out of the moulded block, and rotate through 180° into the down position.

Paper Roll Holder

Replace paper roll by :A)

Take hold of paper roll.

B)

Place over plastic tube.

C)

Fit one end of tube over tab on holder.

D)

Gently spring holder to fit other tab into tube.

Gynae Stirrups Adjust Gynae Stirrups to suit patient by :A)

Unlocking the locking knobs.

B)

Adjust position of stirrup.

C)

Tighten locking knobs.

7

AKRON 9221A, 9221B, 9221C, 9222A, 9222B, 9222C, 9231A, 9231B, 9231C, 9232A, 9232B, 9232C

4. Accessories – Operating Instructions Gynae Troughs Adjust Gynae Troughs to suit patient by :A)

Unlocking the locking knobs.

B)

Adjust position of trough.

C)

Tighten locking knobs.

Cyriax Horns Adjust Cyriax Horns to suit patient by :A)

Unlocking the locking knobs.

B)

Adjust position of horns.

C)

Tighten locking knobs.

Arm Support Adjust Arm Support to suit patient by :A)

Unlocking the locking knobs.

B)

Adjust position of arm support.

C)

Tighten locking knobs.

8

AKRON 9221A, 9221B, 9221C, 9222A, 9222B, 9222C, 9231A, 9231B, 9231C, 9232A, 9232B, 9232C

4. Accessories – Operating Instructions Hole & Horn To fit Horn into Hole :A)

Simply locate horn into hole.

B)

Ensure horn is fully inserted prior to use.

Lean Back Frame To adjust Lean Back Frame :A)

Remove locating pins from frame.

B)

Slide frame to required position.

C)

Replace pins into holes at the end of the frame.

Fixation Rails

Ensure straps are correctly located through fixation rails before use.

9

AKRON 9221A, 9221B, 9221C, 9222A, 9222B, 9222C, 9231A, 9231B, 9231C, 9232A, 9232B, 9232C

5. Cleaning and Decontamination WARNING Do not use Alkalis or other organic solvents for routine cleaning. Replace torn or damaged vinyl immediately. Always cover vinyl with fresh paper or sheet between patients. If contamination is known or suspected always decontaminate couch before use.

Frequency of routine couch cleaning will depend on exact application. CLEANING / DECONTAMINATION Wear suitable protective clothing Disconnect mains supply Locate couch in a suitable cleaning area with castors disengaged or wheels locked. A) B) C)

Using a clean damp cloth, warm water and soap carefully wipe couch from top to bottom, taking care around electrical components. Wipe couch carefully from top to bottom using a damp cloth and clean water. Wipe couch carefully dry with clean paper towels from top to bottom.

If DECONTAMINATING then repeat steps a) to c) using a dilute Hypochlorite / warm water mixture (10,000ppm) instead of warm water and soap. Safely discard cleaning / decontaminating materials. Wash hands thoroughly. Put couch back into service.

6. Troubleshooting – Electric Actuator Symptom Actuator will not work

Actuator runs when Bar is not pressed (Foot Bar Switch)

Possible cause Power disconnected

Action Ensure mains supply is connected

Fuse blown

Replace fuse in socket

Hand/footswitch disconnected Out of balance system

Check that the hand/foot switch is fully inserted into the actuator Vent air tube by disconnecting from actuator, then reconnect

If the problem persists consult your local Akron Supplier.

10

AKRON 9221A, 9221B, 9221C, 9222A, 9222B, 9222C, 9231A, 9231B, 9231C, 9232A, 9232B, 9232C

7. Maintenance Check couch visually before use. Carry out routine servicing every six months or more frequently if in heavy use. Routine servicing or repair must only be performed by suitably qualified person.

WARNING Before commencing any maintenance activity, disconnect the couch from the electrical supply. Plug acts as disconnect device. Examine the couch for any signs of damage. Make sure that all nuts, bolts and other fasteners are tight. Do not over tighten as this may cause binding. Upholstery fasteners should be checked, tightened or replaced if necessary. Check section hinge pins to ensure that no pin protrudes. Check gas strut controls, throughout the full range of movement for locking and assistance. Check hydraulic couches for smooth operation and signs of leakage.

WARNING All electrical checks should be performed by a suitably qualified and licensed electrician. Neither BLUE or BROWN wires are to be connected to the earth terminal of a three pin plug. Examine the flexible cables for cuts, abrasions, kinking or other deterioration and replace if necessary. Ensure that the power supply connector plug is securely attached. Check mains plug connections are tight and fuse is correctly rated (5A).

11

AKRON 9221A, 9221B, 9221C, 9222A, 9222B, 9222C, 9231A, 9231B, 9231C, 9232A, 9232B, 9232C

8. Warranty and Service (UK only) Huntleigh Akron’s standard terms and conditions apply to this couch. A copy is available upon request. These contain full details of warranty terms and do not limit the statutory rights of the consumer. For service or maintenance please contact: Service Department Huntleigh Healthcare 310-312 Dallow Road Luton Beds LU1 1TD

Telephone: 01582 745700 Fax: 01582 745869

For information on this product, or any other Huntleigh Akron product, please contact: Huntleigh Akron 1 Farthing Road Ipswich IP1 5AP

Telephone: 01473 461042 Fax: 01473 462924

Huntleigh Akron T/A a Division of Huntleigh Nesbit Evans Limited A Member of the Huntleigh Technology PLC Group of Companies © Huntleigh Technology PLC 2000. If for any reason your couch is being returned, please inform Huntleigh Akron prior to sending, and: 1. 2. 3. 4.

Clean the product, as described in the cleaning section. Pack it in suitable packing. Attach the decontamination certificate (or other written statement declaring that the product has been cleaned) to the outside of the package. Mark the package “Service Department”.

Manufactured in the UK by Huntleigh Akron. As part of the ongoing development programme this company reserves the right to modify specifications and materials of this couch without notice.

12

AKRON 9221A, 9221B, 9221C, 9222A, 9222B, 9222C, 9231A, 9231B, 9231C, 9232A, 9232B, 9232C

8. Warranty and Service (UK only) Huntleigh Akron’s standard terms and conditions apply to this couch. A copy is available upon request. These contain full details of warranty terms and do not limit the statutory rights of the consumer. For service, maintenance and any questions regarding this, or any other Huntleigh Akron Product, please contact: Huntleigh Akron 1 Farthing Road Ipswich Suffolk IP1 5AP. England Telephone: +44 (0) 1473 461042 Fax: +44 (0) 1473 462924 Huntleigh Akron T/A a Division of Huntleigh Nesbit Evans Limited A Member of the Huntleigh Technology PLC Group of Companies © Huntleigh Technology PLC 2000. If for any reason your couch is being returned, please inform Huntleigh Akron prior to sending and: 1. 2. 3. 4.

Clean the product, as described in the cleaning section. Pack it in suitable packing. Attach the decontamination certificate (or other written statement declaring that the product has been cleaned) to the outside of the package. Mark the package “Service Department”.

Manufactured in the UK by Huntleigh Akron. As part of the ongoing development programme this company reserves the right to modify specifications and materials of this couch without notice.

9. Revision Status

9221 / 9222 / 9231 / 9232 PAGES ALL PAGES ALL PAGES PAGES 12 & 13 PAGE 2

ISSUE UM - 01 UM - 02 UM - 03 UM - 04 (DCN958)

WRITTEN S.Rees S.Rees J. Austin J. Barker

13

DATE 02/06/98 02/12/98 15/11/99 30/10/00

AKRON 9221A, 9221B, 9221C, 9222A, 9222B, 9222C, 9231A, 9231B, 9231C, 9232A, 9232B, 9232C

10. Technical Specification

Head Length (cm) Foot Length (cm) Width (cm) Overall Length (cm) Height Range (cm) Max. Load Weight Elevation Control Configuration

9221A

9222A

9221B

9222B

9221C

9222C

63±1.5 124±1.5 63±1.5 70±1.5 188.5±3 44.5±1.5 93±1.5 180 Kg Hydraulic

63±1.5 124±1.5 63±1.5 70±1.5 188.5±3 44.5±1.5 93±1.5 180 Kg Electric

46±1.5 136.5±1.5 63±1.5 70±1.5 184±3 44.5±1.5 93±1.5 180 Kg Hydraulic

46±1.5 136.5±1.5 63±1.5 70±1.5 184±3 44.5±1.5 93±1.5 180 Kg Electric

46±1.5 136.5±1.5 63±1.5 70±1.5 184±3 44.5±1.5 93±1.5 180 Kg Hydraulic

46±1.5 136.5±1.5 63±1.5 70±1.5 184±3 44.5±1.5 93±1.5 180 Kg Electric

Electrical Data 230v Actuator Internal Fuse Rt Current Power Mains Plug Fuse Rt (UK)

220-240v T1.6A x 1 1.6A 480W 5.0A x 1

220-240v T1.6A x 1 1.6A 480W 5.0A x 1

220-240v T1.6A x 1 1.6A 480W 5.0A x 1

115v F4.0A x 1 3.3A 380W

115v F4.0A x 1 3.3A 380W

Electrical Data 115v Actuator Internal Fuse Rt Current Power

115v F4.0A x 1 3.3A 380W

14

AKRON 9221A, 9221B, 9221C, 9222A, 9222B, 9222C, 9231A, 9231B, 9231C, 9232A, 9232B, 9232C

10. Technical Specification

Head Length (cm) Mid Length (cm) Foot Length (cm) Width (cm) Overall Length (cm) Height Range (cm) Max. Load Weight Elevation Control Configuration

9231A

9232A

9231B

9232B

9231C

9232C

63±1.5 58±1.5 74±1.5 63±1.5 70±1.5 198±4.5 44.5±1.5 93±1.5 180 Kg Hydraulic

63±1.5 58±1.5 74±1.5 63±1.5 70±1.5 198±4.5 44.5±1.5 93±1.5 180 Kg Electric

46±1.5 58±1.5 81.5±1.5 63±1.5 70±1.5 188.5±4.5 44.5±1.5 93±1.5 180 Kg Hydraulic

46±1.5 58±1.5 81.5±1.5 63±1.5 70±1.5 188.5±4.5 44.5±1.5 93±1.5 180 Kg Electric

46±1.5 58±1.5 81.5±1.5 63±1.5 70±1.5 188.5±4.5 44.5±1.5 93±1.5 180 Kg Hydraulic

46±1.5 58±1.5 81.5±1.5 63±1.5 70±1.5 188.5±4.5 44.5±1.5 93±1.5 180 Kg Electric

Electrical Data 230v Actuator Internal Fuse Rt Current Power Mains Plug Fuse Rt (UK)

220-240v T1.6A x 1 1.6A 480W 5.0A x 1

220-240v T1.6A x 1 1.6A 480W 5.0A x 1

220-240v T1.6A x 1 1.6A 480W 5.0A x 1

115v F4.0A x 1 3.3A 380W

115v F4.0A x 1 3.3A 380W

Electrical Data 115v Actuator Internal Fuse Rt Current Power

115v F4.0A x 1 3.3A 380W

15

AKRON 9221A, 9221B, 9221C, 9222A, 9222B, 9222C, 9231A, 9231B, 9231C, 9232A, 9232B, 9232C

10. Technical Specification IEC 601-1 Classification Check serial number label for classification 230v

115v

Double Insulated

Double Insulated

Class 1

Type B equipment

Type B equipment

Type B equipment

Attention consult this manual

Attention consult this manual

Attention consult this manual

16

115v

Huntleigh Akron, 1 Farthing Road, Ipswich, Suffolk, IP1 5AP, England Tel: +44 (0) 1473 461042 Fax: +44 (0) 1473 462924

792-000-04