electronic_convex_probe_ust-979-3-5_instruction_man.pdf
Page 1
MN1-5217
MN1-5217Rev.10
Rev.8
Electronic Convex Probe
UST-979-3.5
Instruction Manual
MN1-5217 Rev.10
i
Page 2
MN1-5217 Rev.8
ii
Page 3
MN1-5217 Rev.8
Introduction
This is an instruction for model UST-979-3.5, an ultrasound probe.
Read the manual carefully before using the instrument. Take special note of the items in section 1, "Safety
Precautions".
Keep this manual securely for future reference.
The CE mark on the probe indicates that this probe is valid when it is connected to equipment
bearing the CE mark that is specified as available in section 2 of this document. Therefore, if a
probe bearing the CE mark is connected to equipment that is specified as available but does not
have a CE mark, part of this instruction manual may not apply.
Symbols used in this document
The terms below are used in the safety information provided to prevent hazards and injuries to the operator
or patients. The severity of the hazard and injury that can occur when failing to observe the displayed safety
information are indicated in four levels: "Danger", "Warning", "Caution" and "Note".
Danger
Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury to
the operator or patient.
Warning
Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury to
the operator or patient.
Caution
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury to
the operator or patient, or property damage only.
Note
Indicates a strong request concerning an item that must be observed in order to prevent damage or
deterioration of the equipment and also to ensure that it is used efficiently.
The type of safety information is indicated by the symbols below.
This symbol means attention is required.
This symbol means that the described action is prohibited.
This symbol means the described action is mandatory.
iii
Page 4
MN1-5217 Rev.8
CONTENTS
1. Safety Precautions
1-1. Intended use......................................................................................................................1
1-2. Usage precautions..............................................................................................................1
1-2-1. Warnings and safety information.....................................................................................2
1-2-2. Washing, disinfection and sterilization precautions.............................................................3
1-2-3. Labels.........................................................................................................................4
2. Specifications and Parts name
2-1. Principles of operation.......................................................................................................9
2-2. Specifications...................................................................................................................10
2-3. Performance.....................................................................................................................11
2-4. Names of each parts.......................................................................................................11
2-5. Environmental conditions...............................................................................................12
2-5-1. Operating environmental conditions.............................................................................12
2-5-2. Storage environmental conditions................................................................................12
2-6. Classification of ME equipment......................................................................................12
3. Preparations for Use
3-1. Start up check.................................................................................................................13
3-1-1. Visual check.............................................................................................................13
3-1-2. Verification of washing, disinfection and sterilization..................................................13
3-1-3. Verification of operation.............................................................................................13
4. Usage
4-1. Operation.........................................................................................................................15
4-2. Connecting to the ultrasound diagnostic instrument......................................................16
4-3. Removing from the ultrasound diagnostic instrument....................................................17
4-4. Precautions when performing puncture operations.........................................................18
4-5. Actions to be taken when an abnormal state is detected..................................................19
4-5-1. Ensuring safety of patients...........................................................................................19
4-5-2. Handling the instrument.............................................................................................19
5. Washing, Disinfection and Sterilization
5-1. Washing...........................................................................................................................22
5-1-1. Probe tip..................................................................................................................22
5-1-2. Cable and connector....................................................................................................22
iv
Page 5
MN1-5217 Rev.8
5-2. Disinfection.....................................................................................................................23
5-2-1. Chemical disinfection..................................................................................................23
5-2-2. Gas disinfection.........................................................................................................24
5-3. Sterilization......................................................................................................................25
5-3-1. Ethylene oxide gas (EOG) sterilization...........................................................................25
6. Storage
6-1. Actions before storing the probe..................................................................................27
6-2. Environmental conditions for storage.............................................................................27
7. Moving and Transporting
7-1. Moving and transporting...............................................................................................29
7-2. Preparing the probe and accessories for moving.............................................................29
7-3. Packing for transportation.............................................................................................29
7-4. Environmental conditions during transportation..........................................................29
8. Periodic Inspection
8-1. Safety tests......................................................................................................................31
8-2. Testing of measurement tolerances..................................................................................32
8-2-1. Conducting tests............................................................................................................32
8-2-2. Result judgement..........................................................................................................32
9. Configuration
9-1. Standard configuration....................................................................................................33
9-2. Options............................................................................................................................33
10. Disposal of the Device........................................................................................................35
This Instruction Manual contains the main body of 36pages and 5pages until the CONTENTS.
v
Page 6
MN1-5217 Rev.8
vi
Page 7
MN1-5217 Rev. 8
1. Safety Precautions
1-1. Intended use
This probe is intended for use by a doctor or other qualified operator when placed into direct contact with the
skin making ultrasonic observations of surrounding organs.
Caution
Do not use this equipment for other than its intended purpose.
Use for other purposes can cause burns or other injuries to the patient or operator.
1-2. Usage precautions
The terms below are used in the safety information provided to prevent hazards and injuries to the operator
or patients. The severity of the hazard and injury that can occur when failing to observe the displayed safety
information are indicated in four levels: "Danger", "Warning", "Caution" and "Note".
Danger
Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury to
the operator or patient.
Warning
Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury to
the operator or patient.
Caution
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury to
the operator or patient, or property damage only.
Note
Indicates a strong request concerning an item that must be observed in order to prevent damage or
deterioration of the equipment and also to ensure that it is used efficiently.
The type of safety information is indicated by the symbols below.
This symbol means attention is required.
This symbol means that the described action is prohibited.
This symbol means the described action is mandatory.
-1-
Page 8
MN1-5217 Rev. 8
1-2-1. Warnings and safety information
Warning
Follow the information in this manual and the documentation supplied with any equipment used
together with this probe.
Use that is not in accordance with the supplied documentation can result in a serious or moderate
injury, equipment breakdown, or physical damage that impairs operation.
Be sure to preparations for use.
Use of the probe while failing to notice an abnormal condition can result in injury to the operator or
patient. If any abnormalities are noted on the probe in the start up inspection, immediately stop using
it and contact one of our offices and/or distributor's offices listed on the back cover. See section 3-1
“Start up check” for the start up inspection content and procedure.
Do not use on the eyes.
This probe is not intended for use on the eyes. The acoustic output can have an adverse effect on the
eyes.
Do not attempt to disassemble, modify, or repair the probe.
Electric shock or other unforeseen accidents could result. Contact one of our offices and/or distributor's offices listed on the back cover to request repair.
Clean, disinfect and sterilize before using the probe as necessary.
Perform properly wash, disinfect and sterilize after use.
Otherwise, there is a risk of infection. Note that the probe is not sterilized at the factory. Before using
the probe first, be sure to wash, disinfect and sterilize it as required.
Wear medical gloves during examination.
Conducting examinations with the bare hands can expose the operator to a risk of infection.
Dispose of probes used for patients with Creutzfeldt-Jakob disease.
Otherwise, there is a risk of infection to the operator or patient. Currently, there are no methods for
washing, disinfecting and sterilizing intraoperative probes which have been used on patients afflicted
by Creutzfeldt-Jacob disease.
When using ultrasound contrast agent, follow the supplied documentation.
Unexpected accidents could result. Check the state of the patient and take appropriate precautions
to avoid side effects.
Do not use the probe fallen on to floor.
Ohterwise, there is a risk of infection. Stop the operation and perform the procedure in section 8
"Periodic Inspection", section 5 "Washing, Disinfection and Sterilization" and section 3-1 "Start up
check".
Caution
Constantly check for anything abnormal about the patient’s condition and probe.
Continued use without noticing that an abnormal condition has occurred can result in an electric
shock and injury to the operator or patient. If an abnormal condition occurs, immediately move the
probe away from the patient and stop use of the probe.
The probe is vulnerable to damage by impact. Therefore, handle it with care.
There is a risk of damage to the probe when the probe is fallen or hit somewere.
Do not use this probe with other equipment except for those specifically approved in the manual.
Use with unapproved equipment can result in an electric shock, burn, or other injury to the patient or
operator and damage to the probe and the other equipment.
-2-
Page 9
MN1-5217 Rev. 8
Scan for the minimum length of time necessary for the diagnosis and at the lowest suitable output.
Overuse can adversely affect the internal tissues of the patient.
For details about the acoustic output, please refer to the documentation supplied with the ultrasound
diagnostic instrument.
Regularly perform maintenance inspection and safety tests of the ultrasound diagnostic instrument
and probe.
If you use equipment for a long period of time, it can reduce the performance, or cause smoke or
fire. If anything unusual occurs, immediately stop using it and contact one of our offices and/or
distributor's offices listed on the back cover.
Use, move and transport the probe under the environmental conditions specified in this manual.
Otherwise, it may be damaged.
See section 2-5 "Environmental conditions" and section 7-4 "Environmental conditions during
transportation".
1-2-2. Washing, disinfection and sterilization precautions
Warning
Wear protective gloves and other protective gear during washing, disinfection and sterilization.
Handling of the probe with your bare hands before disinfection or sterilization can result in an
infection.
After soaking in cleaning agents, thoroughly wash the probe with running water.
Residual cleaning agents can cause an adverse reaction on the bodies of the operator or patient.
After chemical disinfection , thoroughly wash the probe with sterilized water.
Residual chemicals can cause an adverse reaction on the bodies of the operator or patient.
Perform aeration completely after gas disinfection and sterilization.
Residual gas can cause an adverse reaction on the bodies of the operator or patient.
Do not wash, disinfect or sterilize using procedures other than those specified in this manual.
Infection could result due to incomplete washing disinfection or sterilization. It can also result in
damage to the probe or reduced performance. The probe cannot withstand autoclave sterilization or
boiling and other types of sterilization at temperatures exceeding 60°C (140°F).
For details on the usage conditions of chemicals and sterilization procedures, refer to the documentation
supplied with the respective chemical or sterilization equipment.
Infection could result due to incomplete disinfection or sterilization. This could also cause
deterioration of the probe.
Caution
Do not place the probe tip in any liquids beyond the range
shown in the figure right.
Use when liquid has gotten inside the connector can result in
a risk of electric shock to the operator or patient. If liquid gets
inside the connector, immediately stop use and contact one of
our offices and/or distributor's offices listed on the back cover.
25 mm or less
Water or solution
-3-
Page 10
MN1-5217 Rev. 98
1-2-3. Labels
(1) Probe unit
Label 1
Label 2
Label 3
Label 1
Electronic convex probe mark
3.5
L
RE
EA
SE
Frequency
MHz
LO
CK
-4-
Page 11
MN1-5217 Rev. 98
Label 2
This equipment complies with Directive
93/42/EEC relating to Medical Device.
IPX7
IPX7 mark
See section 2-2, “Specifications”.
Type BF applied part
Do not waste the instrument as general waste. Comply
with a local regulation.
See section 10.
Safety warning sign
Biohazard
See section 5.
Follow the instruction manual to operate this instrument.
If not avoided, may result in injury, property damage, or
the equipment trouble.
Label 3
Manufacturer
Model, Serial No.
-5-
Page 12
MN1-5217 Rev. 8
(2) Storage case
Label A
Label B
-6-
Page 13
MN1-5217
MN1-5217Rev.
Rev.108
Label A
Model
Serial No.
Label B
2012
This equipment complies with Directive
93/42/EEC relating to Medical Device.
DATE OF MANUFACTURE
(in case of 2012)
2012
MANUFACTURER
-7-
Page 14
MN1-5217 Rev. 8
-8-
Page 15
MN1-5217 Rev. 8
2. Specifications and Parts name
2-1. Principles of operation
This probe and the ultrasound diagnostic instrument enable image diagnosis using ultrasonic waves. These
instruments operate under the principles described below.
(1) W hen an electric pulse signal is applied from the transmitter to the transducer of the probe, the transducer
operates by converting electrical vibrations to mechanical vibration energy for emitting pulse-shaped
ultrasonic waves into the body part contacting the transducer or into liquid or other medium.
(2) The emitted ultrasonic waves are reflected by boundaries with different acoustic characteristics (acoustic
impedance) within the body.
(3) The transducer is also used to receive reflected ultrasonic waves. The transducer vibrates mechanically due
to the received ultrasonic vibrations and uses an electro-mechanical conversion operation to convert the
received mechanical vibrations to electric energy. The received echo is also converted to electric signals
and a brightness modulation operation is used to convert the electric pulses to shades of brightness for
forming an image.
-9-
Page 16
MN1-5217 Rev. 8
2-2. Specifications
Application regions:
Form of application to patient:
Connectable instruments:
Field of view:
Frequency:
Cable length:
Weight:
Service life:
Abdomen, general areas
Surface
SSD-900, SSD-1000, SSD-3500, SSD-4000, ProSound 6
60°
3.5 MHz
2.0 m
1,070 g
Three years
Range of applied part
Parts treated as applied parts
IPX7 range
Ultrasonic irradiation area, see the section 2-4.
Probe tip itself and 1 m of the cable near the probe tip.
As shown in the figure below.
External dimensions:
As shown in the figure below.
IPX7 range
50
Cable length
Unit: mm
Remarks
The dimensions and weight are within ±10% of the indicated values.
-10-
Page 17
MN1-5217 Rev. 8
2-3. Performance
For measurement tolerances, operating tolerances and other data, refer to the instruction manual for the
ultrasound diagnostic instrument.
2-4. Name of each parts
Probe tip
This area is held during operation.
Cable
This cable propagates the ultrasonic signals
that are sent and received.
Front mark
The round protrusion indicates the
direction of the front mark (direction
mark) on the image display.
Connector
This is the part that connects the ultrasound
diagnostic instrument and probe. Follow the
instructions in section 4-2.
Ultrasonic irradiation area
This incorporates an electronic convex
transducer.
Caution
Do not pull, bend, twist, or apply excessive force to the cable.
The conductors may break and the cable may become unusable.
Do not subject the ultrasonic irradiation area to hard impact.
This could make the probe unusable.
-11-
Page 18
MN1-5217 Rev. 8
2-5. Environmental conditions
Use and store the probe under the following conditions.
2-5-1. Operating environmental conditions
Ambient temperature:
10°C to 40°C
50°F to 104°F
Relative humidity:
30% to 75%
Atmospheric pressure:
700 hPa to 1060 hPa
Altitude:
3,000 m or less
2-5-2. Storage environmental conditions
Ambient temperature:
–10°C to 50°C
14°F to 122°F
Relative humidity:
10% to 90%
Atmospheric pressure:
700 hPa to 1060 hPa
Caution
Avoid operating or storing the probe in the following locations.
• Locations exposed to water or other liquids
• Locations subject to adverse conditions such as air pressure, temperature, humidity, ventilation,
direct sunlight, dust, or air containing salt, sulfur, or other corrosive substances
• Locations where chemical substances are stored or where gases are generated
Storage in these locations can result in a breakdown or reduced performance.
Avoid rapid temperature change which may cause condensation. Avoid using in locations where
condensation or water droplets can form.
Condensation can occur when moving the probe from a cool location to a warm one. Use when
condensation has occurred can result in a breakdown or reduced performance.
2-6. Classification of ME equipment
•
•
•
•
Classification based on degree of protection against electric shock.. Type BF applied part
Classification for protection against ingress of liquids...................... IPX7 (Watertight equipment)
Operation mode.................................................................................. Continuous operation
Method of sterilization....................................................................... See section 5 “Washing, Disinfection
and Sterilization”
For the range of applied parts, parts treated as applied parts and the range of IPX7, see section 2-2.
-12-
Page 19
MN1-5217 Rev. 8
3. Preparations for Use
3-1. Start up check
3-1-1. Visual check
Visually check the probe tip, ultrasonic irradiation area, cable and connector.
If any holes, indentations, abrasion, cracks, deformation, looseness, discoloration, or other abnormalities
are found, do not use the equipment.
3-1-2. Verification of washing, disinfection and sterilization
Verify that washing, disinfection and sterilization are conducted according to the intended use.
3-1-3. Verification of operation
Connect to the ultrasound diagnostic instrument by following the instructions in section 4-2, “Connecting
to the ultrasound diagnostic instrument” and check that the selected probe match the convex display
and the displayed frequency and check the image for errors.
Remarks
For details on the displayed screens, see the documentation supplied with the ultrasound diagnostic
instrument.
Warning
Be sure to preparations for use.
Using the probe without noticing an abnormal condition can result in injury to the operator or patient.
If an inspection finds an abnormal condition in the probe, immediately stop use and contact one of
our offices and/or distributor's offices listed on the back cover.
Caution
Do not use the probe if the selected probe and image do not match the frequency.
An incorrect acoustic output can result in burns or other injuries to the patient. Contact one of our
offices and/or distributor's offices listed on the back cover.
-13-
Page 20
MN1-5217 Rev. 8
-14-
Page 21
MN1-5217 Rev. 8
4. Usage
4-1. Operation
Bring the ultrasonic irradiation area of the probe into contact with the skin surface. An image of the region
of interest is displayed on the monitor of the ultrasound diagnostic instrument. For details on displaying and
adjusting the screens, see the documentation supplied with the ultrasound diagnostic instrument.
Caution
Do not move the probe with excessive force.
Pressing down with more force than necessary can cause injury to the patient.
Scan for the minimum length of time necessary for the diagnosis and at the lowest suitable output.
There is the possibility that the patient’s internal tissues could be affected.
For details about the acoustic output, please refer to the documentation supplied with the ultrasound
diagnostic instrument.
Do not touch the connector terminal pin of the probe.
The probe may deteriorate or be damaged due to electrostatic discharge.
Do not touch the electronic probe connecting socket of the diagnostic instrument and the patient at
the same time.
It can cause electric shock to the patient.
-15-
Page 22
MN1-5217 Rev. 8
4-2. Connecting to the ultrasound diagnostic instrument
The lock lever of the connector moves over the range shown in the figure at
right.
Align the ○ mark with the LOCK or RELEASE position and lock or release
the probe connector.
Connect the probe to the electronic probe connecting socket of the diagnostic
instrument ( probe connector ) by following the procedure below.
RELEASE
LOCK
○ mark
Lock lever
Movable
range
• Connection procedure
The probe is connected when in one of the following states.
• The power switch is set to OFF.
• The image displayed on the ultrasound diagnostic instrument is
frozen.
Before inserting the probe into the probe connector, check that the connector
pins are not bent.
Probe
connector
1. Turn the connector lock lever to align the ○ mark on the lever with the
RELEASE position.
2. Firmly insert the connector into the probe connector on the ultrasound
diagnostic instrument.
RELEASE
LOCK
3. Turn the lock lever clockwise by 1/4 turn until the ○ mark is aligned with
the LOCK position.
4. Check that the connector is firmly inserted into the probe connector on
the instrument.
This completes connection of the probe.
Caution
If there is resistance when trying to turn the lock lever when connecting the connector, do not forcibly
try to connect it. Instead, correctly perform the steps for connecting the connector and firmly insert
it into the probe connector.
Forcibly turning the lever may damage the connector and the probe connector on the instrument.
-16-
Page 23
MN1-5217 Rev. 8
4-3. Removing from the ultrasound diagnostic instrument
The lock lever of the connector moves over the range shown in the figure at
right.
Align the ○ mark with the LOCK or RELEASE position and lock or release
the probe connector.
Use the procedure below to remove the probe from the electronic scan probe
connector of the ultrasound diagnostic instrument ( probe connector ) .
RELEASE
LOCK
○ mark
Lock lever
Movable
range
• Removal procedure
The probe is removed when in one of the following states.
• The power switch is set to OFF.
• The image displayed on the ultrasound diagnostic instrument is
frozen.
1. Turn the connector lock lever to align the ○ mark on the lever with the
RELEASE position.
2. Firmly grasp the connector unit and pull it out from the probe connector
of the ultrasound diagnostic instrument.
RELEASE
LOCK
This completes the removal of the probe.
After use, perform washing, disinfection and sterilization of the probe
by following the procedure in section 5 “Washing, Disinfection and
Sterilization".
If the probe will not be used for an extended period of time, store it by
following the instructions in section 6 “Storage".
Probe
connector
-17-
Page 24
MN1-5217 Rev. 8
4-4. Precautions when performing puncture operations
Warning
Carefully read the usage precautions in the documentation supplied with the puncture adapter.
Be sure that the preparations for use are completed before using.
Puncturing must be performed by a skilled doctor.
Improper puncturing can injure the patient. Puncturing operations must be performed by a doctor
who fully understands the characteristics of ultrasound diagnostics and who is skilled and has a
thorough knowledge of puncture operations under an ultrasound guide.
The puncture adapter must be properly mounted on the probe during use.
Puncturing with the puncture adapter improperly mounted or the puncture adapter uninstalled can
result in the puncture adapter coming off during puncturing or puncturing of an unintended body
part, causing injury to the patient. For details about the puncture adapter mounting procedure, see the
documentation supplied with the puncture adapter.
Be sure that the puncture adapter and the needle are sterilized before use.
Use of unsterilized items can cause an infection. For details concerning the puncture adapter
sterilization procedure, see the documentation supplied with the puncture adapter.
For the acoustic medium, use sterilized physiological saline.
Using an unsterilized ultrasound medium can cause an infection on the patient.
Use a compatible puncture needle size.
Use of a puncture needle that is not a compatible size can result in the puncture adapter coming off
during puncturing or puncturing of an unintended body part, causing injury to the patient. For the
compatible puncture needle sizes, see the documentation supplied with the puncture adapter.
Always use a straight needle.
Puncturing of an unintended body part can cause injury to the patient.
During the puncture operation, display a suitable puncture guide line on the screen of the ultrasound
diagnostic instrument.
Puncturing of an unintended body part can cause injury to the patient. Display the puncture guide
line on the screen referring to the documentation supplied with the ultrasound diagnostic instrument,
to use it as an aid in determining the puncturing direction.
Constantly check the safety in the needle insertion direction using the needle echo rendered by the
ultrasonic wave.
A bent puncturing needle can result in puncturing of an unintended body part and cause injury to
the patient.
Check that no other organs lie in the puncture path.
If another organ lies in the puncture path, an unintended body part can be punctured and cause injury
to the patient. Before puncturing, carefully check the body parts and constantly confirm the needle
echo during the operation.
Do not try to forcibly perform operations.
If excessive force is applied in a direction other than the insertion direction of the puncturing needle,
the puncturing needle can come off the guide line, resulting in puncturing of an unintended body
part, causing injury to the patient.
-18-
Page 25
MN1-5217 Rev. 8
Warning
Before using a needle cannula with the puncture adapter as a guide, first check that the cannula
moves smoothly through the tube without causing any damage on the surface of the cannula and then
operate with caution.
If the cannula does not move smoothly or is forced to bend when inserted in or pulled out of the
puncture adapter, it may damage the insulation membrane covering the cannula and may cause burns
to the tissue exposed to the damaged area of the cannula.
Do not puncture the heart region.
Puncturing the heart region may cause a micro electric shock.
Caution
Handle the needle carefully to ensure that the probe is not damaged.
Using a probe that has been damaged by a needle can result in injury to the operator or patient.
4-5. Actions to be taken when an abnormal state is detected
4-5-1. Ensuring safety of patients
Immediately move the probe away from the patient and quit operation.
Keep the patient in safe condition and administer the required medical treatment.
4-5-2. Handling the instrument
Turn off the ultrasound diagnostic instrument, remove its plug from the AC socket and sterilize if it is
contaminated. For details, refer to the instruction manual for the ultrasound diagnostic instrument.
Caution
Do not use a probe where a problem has been found.
Using a probe in an abnormal state can cause injury to the patient. Contact one of our offices and/or
distributor's offices listed on the back cover.
-19-