TITAN-Compact SK- xxx Instruction Manual

SAFETY PRECAUTIONS All safety messages are identified by the following, “WARNING” or “CAUTION”, of ANSI Z535.4 (American National Standard Institute: Product Safety Signs and Labels). The meanings are as follows: A potentially hazardous situation which, if not WARNING avoided, could result in death or serious injury. A potentially hazardous situation which, if not CAUTION avoided, may result in minor or moderate injury. This manual is subject to change without notice at any time to improve the product. Product specifications are subject to change without any obligation on the part of the manufacturer. When using the SK-WP, the following safety precautions should always be followed. WARNING Use only the specified AC adapter for the scale. Other adapters may cause damage. (AC adapter is optional.) Internal service or adjustment to this product should be performed by a qualified person. CAUTION Avoid installing the scale in direct sunlight, which may cause discoloration or malfunctions. Do not mix battery types, or new and old batteries. Replace with all new batteries at the same time. If the scale is not to be used for a long period of time, remove all batteries from the battery compartment to avoid leakage. Avoid overloading to the scale. Avoid using the weighing platform to move the scale, as that could cause damage to the scale. Avoid chemical solvents. Clean the scale with water. When the scale is used with an AC adapter, the scale does not conform to IP65 protection. IP65 Degrees of protection against water: Protected against water jets. Degrees of protection against solid foreign objects: Dust-tight. International Protection of IEC529. -1-

PARTS DESCRIPTION Weighing Platform

Spirit level

ON/OFF key Turns the scale power on/off.

UNITS key (only for (k)g- lb model) Changes weighing units, (k)g or lb.

RE-ZERO key

Display

Sets display to zero or subtracts weight of a container.

Four leveling feet

Battery cover

Batteries are not included.

Battery cover lock Battery compartment AC adapter socket Battery cover lock DISPLAY STABLE indicator Indicates when the reading is stable.

Weighing unit

Polarity NET indicator Indicates when NET weight is displayed. (Tare function is used.) ZERO indicator Indicates when the scale zero is correct.

-2-

Weighing unit for (k)g-lb model only.

PREPARATION Installing Batteries / Connecting the AC Adapter Installing Batteries CAUTION When replacing batteries, be careful not to apply too much force to the weighing platform. An excessive force could damage the scale. Unlock and remove the battery cover. (See illustration at the right) Insert six new batteries (R20P / LR20 / D size) into the battery compartment, taking extreme care to that the plus and minus polarities are observed. Be sure to install and lock the battery cover after installing the batteries. New six batteries. (R20P/ LR20/ D size) AC Adapter (Optional) CAUTION When using an AC adapter, the scale doesn’t comply with IP65. The AC input requirement could be 100, 120, 220, 230 or 240 volts (50/60Hz) depending on the area where used, so please verify that the adapter is the correct type. Plug the AC adapter to the AC adapter socket inside the battery compartment.

Setting up the Scale CAUTION Avoid installing the scale in direct sunlight, that may cause discoloration or malfunctions. Place your SK-WP on a firm weighing table so that the scale is level. The scale will not perform accurately when it is not level. Place the scale on a firm surface and adjust the feet to level the scale, while using the sprit level, for accurate weighing. -3-

WEIGHING Before Weighing Automatic Power-Off Function. If the scale is left ON and the stable indicator is displayed, the automatic power-off function turns the power off after approximately five minutes (factory setting). To disable or enable the function, press the [ON/OFF] key while pressing the [RE-ZERO] key. The scale stores this setting. To verify this, press both the [RE-ZERO] and [UNITS] keys while in the weighing mode. (See "CALIBRATION" about the [UNITS] key.) poff0 Function disabled poff1 Function enabled Error Message e Overload ----- The scale zero is out of range lb Low battery Calibration May be Required Before Weighing Read “CALIBRATION” first and if necessary, calibrate your scale for accurate weighing.

Weighing Procedures 1.

Turn on the scale. Press the [ON/OFF] key to turn on the scale. Then the scale displays all segments for a few seconds and then 0 will be displayed.

2.

Start weighing If you do not use a container for weighing, Press the [RE-ZERO] key to display 0 . Verify the reading is 0. Place objects on the weighing platform to weigh. is displayed. When the reading becomes stable, the stable indicator If you use a container for weighing, Place an empty container on the platform. to be displayed and press the Wait for the stable indicator [RE-ZERO] key. Place the objects to be weighed in the container. When is displayed. the reading becomes stable, the stable indicator Select the weighing unit, --- Only for the “(k)g-lb” model--If you use the (k)g-lb model, press the [UNITS] key to select weighing with either (k)g or lb as the unit. Normally scales power up in lb when shipped from the factory. To power up in (k)g, turn the scale off. Press and hold the [UNITS] key, then press the [ON/OFF] key. The scale will start with (k)g. To return to the original setting, repeat this instruction. -4-

CALIBRATION When to Calibrate Calibration may be required when the scale is initially installed, if it is moved a substantial distance, or in accordance with local regulations. This is necessary because the weight of a mass in one location is not necessarily the same in another location. Also, with time and use, mechanical deviations can occur. The Position of the [UNITS] key for the Calibration The (k)g model has no [UNITS] key, but the key for the calibration is located under the overlay.

Calibration Using a Calibration Weight Calibrate the scale with the following calibration weight. SK-1000WP: 1000g ± 0.1g SK-2000WP: 2000g ± 0.2g SK-5000WP: 5000g ± 0.5g SK-5001WP: 5000g ± 0.5g SK-10KWP: 10kg ± 1g SK-20KWP: 20kg ± 2g SK-30KWP: 30kg ± 2g 1.

Enter calibration mode. Press the [ON/OFF] key to turn the power off. While pressing both the [RE-ZERO] and [UNITS] keys, press the [ON/OFF] key. Then, Cal will be displayed.

2.

Zero calibration Press the [RE-ZERO] key to calibrate zero. Cal0 will be displayed. When you have proceeded to the display other than Cal0 , press the [ON/OFF] key to turn the power off and start over again. Wait for the stable indicator to be displayed and press the [RE-ZERO] key. Calf will be displayed in a few seconds. If the zero calibration only is to be done, press the [UNITS] key. The scale will show end and automatically return to the weighing mode.

3.

Span calibration Place the weight at the center of the platform for accurate calibration. to be displayed and press the Wait for the stable indicator [RE-ZERO] key. The scale will show end and the scale will automatically return to the weighing mode. -5-

Calibration by Gravity Compensation If you have calibration weights at the capacity of the scale, you can calibrate the scale with the weights instead of compensating for the gravity acceleration. The scale is calibrated at 9.798 m/sec2 at the factory. If the gravity acceleration at your location is not the same, calibrate the scale by compensating for the gravity acceleration. (See “The Value of Gravity at Various Locations” and “World Map” and find your location value.) 1.

Enter calibration mode. Press the [ON/OFF] key to turn the power off. While pressing both the [RE-ZERO] and [UNITS] keys, press the [ON/OFF] key. Then, Cal will be displayed.

2.

Select a digit to be changed. Press the [UNITS] key. The previously set value, for example 979,8 , will be displayed. A digit after the comma “,” will be changed by pressing the [RE-ZERO] key. Press the [UNITS] key to move the comma “,” and select a digit to be changed.

3.

Set the new value. Change the value of the gravity acceleration using the [RE-ZERO] and [UNITS] keys.

4.

Save the value in memory. Press and hold the [UNITS] key until end is displayed. The scale will automatically return to the weighing mode.

-6-

SPECIFICATIONS Model

SK-1000WP SK-2000WP SK-5000WP SK-5001WP SK-10KWP SK-20KWP SK-30KWP 1000 g 2000 g 5000 g 5000 g 10 kg 20 kg 30 kg Capacity 2.2 lb 4.4 lb 11 lb --22 lb 44 lb 66 lb 0.5 g 1g 2g 1g 0.005 kg 0.01 kg 0.02 kg Resolution 0.001 lb 0.002 lb 0.005 lb --0.01 lb 0.02 lb 0.05 lb Non-linearity ±1g ±2g ±4g ±4g ±0.01 kg ±0.02 kg ±0.04 kg Repeatability 0.5g 1g 2g 2g 0.005 kg 0.01 kg 0.02 kg Span drift ±0.015% / °C TYP (5°C~35°C / 41°F~95°F) Operating -10°C~40°C / 14°F~104°F, Less than 85%RH temperature Display 25 mm / 0.98 inches, 7 segment liquid crystal display Display Approximately 10 times per second update Power 6 x R20P / LR20 / “D” size batteries or AC adapter Approximately 600 hours with manganese type Battery life 1200 hours with alkaline cells at 20°C / 68°F Platform size 232 (W) x 192 (D) mm / 9.13 (W) x 7.56 (D) in. Dimensions 266 (W) x 280 (D) x 146 (H) mm / 10.48 (W) x 11.03 (D) x 5.75 (H) in. Weight (approx.) 2.9 kg / 6.4 lb 3.2 kg / 7.1 lb Calibration 1000g±0.1g 2000g±0.2g 5000g±0.5g 5000g±0.5g 10kg ±1g 20kg ±2g 30kg ±2g weight Accessories This manual Options AC adapter

The Value of Gravity at Various Locations Amsterdam Athens Auckland NZ Bangkok Birmingham Brussels Buenos Aires Calcutta Cape Town Chicago Copenhagen Cyprus Djakarta Frankfurt Glasgow Havana Helsinki Kuwait Lisbon London (Greenwich) Los Angeles Madrid

9.813 m/s2 9.807 m/s2 9.799 m/s2 9.783 m/s2 9.813 m/s2 9.811 m/s2 9.797 m/s2 9.788 m/s2 9.796 m/s2 9.803 m/s2 9.815 m/s2 9.797 m/s2 9.781 m/s2 9.810 m/s2 9.816 m/s2 9.788 m/s2 9.819 m/s2 9.793 m/s2 9.801 m/s2 9.812 m/s2 9.796 m/s2 9.800 m/s2

Manila Melbourne Mexico City Milan New York Oslo Ottawa Paris Rio de Janeiro Rome San Francisco Singapore Stockholm Sydney Taichung Tainan Taipei Tokyo Vancouver, BC Washington DC Wellington NZ Zurich

-7-

9.784 m/s2 9.800 m/s2 9.779 m/s2 9.806 m/s2 9.802 m/s2 9.819 m/s2 9.806 m/s2 9.809 m/s2 9.788 m/s2 9.803 m/s2 9.800 m/s2 9.781 m/s2 9.818 m/s2 9.797 m/s2 9.789 m/s2 9.788 m/s2 9.790 m/s2 9.798 m/s2 9.809 m/s2 9.801 m/s2 9.803 m/s2 9.807 m/s2

World Map

-8-

3-23-14 Higashi-Ikebukuro, Toshima-ku, Tokyo 170-0013 JAPAN Telephone: [81] (3) 5391-6132 Fax: [81] (3) 5391-6148 A&D ENGINEERING, INC.

1756 Automation Parkway, San Jose, California 95131 U.S.A. Telephone: [1] (408) 263-5333 Fax: [1] (408)263-0119 A&D INSTRUMENTS LIMITED <UK Office>

Unit 24/26 Blacklands Way, Abingdon Business Park, Abingdon, Oxfordshire Telephone: [44] (1235) 550420 Fax: [44] (1235) 550485 A&D INSTRUMENTS LIMITED <German Sales Office>

Große Straße 13 b 22926 Ahrensburg Deutschland Telefon: [49] (0) 4102 459230 Telefax: [49] (0) 4102 459231 A&D Australasia Pty Ltd.

32 Dew Street, Thebarton, South Australia 5031 AUSTRALIA Telephone: [61] (8) 8301-8100 Fax: [61] (8) 8352-7409 A&D KOREA Limited

한국에이.엔.디(주)

대한민국 서울시 영등포구 여의도동 36-2 맨하탄 빌딩 8층 ( 8th Floor, Manhattan Bldg. 36-2 Yoido-dong, Youngdeungpo-ku, Seoul, KOR 전화: [82] (2) 780-4101 팩스: [82] (2) 782-4280 A&D RUS CO., LTD. Компания ЭЙ энд ДИ РУС

121357, Российская Федерация, г.Москва, ул. Верейская, дом 17 ( Bldg. 17, Vereyskaya st., Moscow, 121357 RUSSIAN FEDERATION ) тел.: [7] (495) 937-33-44 факс: [7] (495) 937-55-66 A&D Instruments India Private Limited

( 509, Udyog Vihar, Phase- , Gurgaon - 122 016, Haryana, India ) : 91-124-4715555 : 91-124-4715599 -9-