Incu i Model 101 Operation Manual Oct 2019

INTRODUCTION This Operation Manual deals with the specifications, operation and maintenance of the Incu i. Atom is by no means responsible for any malfunction arising from a user ignoring the instructions for operation and maintenance described in this Manual as well as any accident attributable to repair by someone other than technical personnel belonging to or authorized by Atom. This Manual contains instructions for operating the oxygen controller, the weight monitor and the pulse oximeter. Please skip any section unrelated to your unit. Read this Manual carefully and familiarize yourself with its contents before operating the unit. Keep this Manual where it is readily accessible for reference when needed. If any technical problem should arise, please contact your local Atom representative.

This product is shipped without being disinfected. Be sure to clean and disinfect the unit before using it for the first time after purchase. This product maintains the ambient temperature around an infant by drawing in the air outside and warming it. It does not have the capability to cool the air drawn from outside. Be sure to set the incubator air temperature at least 3°C higher than the ambient temperature. In particular, if a phototherapy unit, a heated humidifier, or some other heat-generating device is used with the incubator, set the incubator air temperature at least 5°C higher than the ambient temperature. If a lower setting is selected, the incubator may not be controlled correctly.

INTENDED USE The Incu i is an incubator for newborns and premature neonates. It is mainly intended for temperature control in neonatal hypothermia, observation and examination in newborn nurseries, prevention of body temperature drop shortly after delivery, and pre-operative and post-operative intensive care in neonatal surgery. This incubator has the capability to control the infant’s skin temperature.

SAFETY INFORMATION Instructions to ensure the safe operation of the unit are found throughout this Manual. Please read the Manual carefully before operating the unit. Please follow the instructions when operating the unit.

Basic Instructions 1. Follow the instructions for the safe use of the unit. Follow the operating instructions described in this Manual for the safe use of the unit. 2. Inspect the unit on a periodical basis. Periodical inspection is needed to use the unit in the optimum condition. 3. Never use the unit if it is found to be defective. If any damage or malfunction of the unit should be noticed, stop using it immediately and contact your local Atom representative. 4. Follow the EMC information given in this Manual. Electric equipment for medical use needs special precautions regarding EMC. It needs to be installed and put into service according to the EMC information provided in this Manual.

1

Definitions of Warning Indication Three levels of warning indication are used throughout this Manual and on the unit. They are defined as follows. A DANGER notice indicates an immediately hazardous situation which, if not avoided, will result in death or serious injury, serious damage to property such as total loss of use of equipment or fire. A WARNING notice indicates an indirectly (potentially) hazardous situation which, if not avoided, will result in death or serious injury, serious damage to property such as total loss of use of equipment or fire. A CAUTION notice indicates a hazardous situation which, if not avoided, can result in minor or moderate injury, partial damage to equipment, and loss of data stored in computers.

Definition of Symbols 1. Symbols to indicate danger, warning or caution Symbol Title and indication General attention Indicates unspecified general danger, warning or caution. Caution: Hot surface Indicates that the surface can be dangerously hot under certain conditions.

2. Symbols to prohibit action Symbol

Title and indication

General prohibition Indicates unspecified general prohibition. Prohibition of disassembly Indicates prohibition of disassembly of the unit where it may cause an electric shock or other hazards. Prohibition of use of fire Indicates prohibition of use of fire where an external use of fire may cause the unit to ignite under certain conditions. 3. Symbols to give instructions for action Symbol

Title and indication

General instruction Indicates unspecified general action on the part of the user. Connect a ground wire Instructs the user to connect the ground wire without fail where the unit is provided with a ground terminal. Remove the power plug from the power outlet Instructs the user to remove the power plug from the power outlet in the case of malfunction or when there is a threat of lightning. 2

4. Symbols of international standards (IEC) Symbol

Title and indication

Equipment partially on Indicates that a part of the device is “ON.” Equipment partially off Indicates that a part of the device is “OFF.” Type BF applied part Indicates that the device is classified as Type BF in terms of the degree of protection against an electric shock. Bell silenced Indicates either a control switch to silence the bell permanently or temporarily, or that the bell is silenced. Manufacturer This symbol indicates the name and the address shown adjacent to the symbol is of the manufacturer. Date of manufacture Indicates the date when the unit was manufactured in the factory. Authorised representative in the european community This symbol indicates the name and the address shown adjacent to the symbol is of the authorised representative in the European Community. WEEE symbol In the EC area, an electrical and electronic product falling in one of the categories specified by “DIRECTIVE 2002/96/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 27 January 2003 on Waste Electrical and Electronic Equipment (WEEE)” should be disposed of in a manner consistent with relevant laws and regulations. This symbol indicates that the above-mentioned requirement applies to this product. Locked Indicates a locked condition. Unlocked Indicates an unlocked condition. See Operation Manual Follow Operation Manual.

5. Other symbols Symbol

Title and indication

Setting Indicates that a setting is increased. Setting Indicates that a setting is decreased.

3

Symbol

Title and indication Main screen display switch Indicates a switch to display the main screen. Trend screen display switch Indicates a switch to display the trend screen. Menu screen display switch Indicates a switch to display the menu screen. Pulse oximeter screen display switch Indicates a switch to display the pulse oximeter screen or the function related to the pulse rate. Weight screen display switch Indicates a switch to display the weight screen or the function related to weighing the infant. Battery Indicates whether the incubator is being powered by a battery or not. Incubator air circulation Indicates the function related to air circulation in the incubator in the incubator mode or that the incubator is in manual control. Setting Indicates set values or the setting procedure. Skin temperature Indicates the function related to the infant’s skin temperature or that the incubator is in servo control. Temperature Indicates, with this symbol alone or with other symbols, a detected temperature or a set temperature alarm. Peripheral temperature Indicates the function related to the infant’s peripheral temperature (skin temperature 2). Low water level/no water Indicates that there is little or no water in the humidity chamber. Defective humidity chamber Indicates that something is wrong with the humidity chamber. Humidity chamber off Indicates that the humidity chamber is not attached properly.

4

Symbol

Title and indication Humidity Indicates the function related to humidity.

O2

Oxygen Indicates the function related to oxygen. Load capacity Indicates the maximum load capacity. Gross weight Indicates that the gross weight when peripheral devices of maximum loading capacity are attached to the product is as inscripted. Avoid getting caught Indicates that the user must avoid getting caught in the gap in the device. AC power indicator The indicator lamp comes on in green when the unit is connected to the AC power source. It comes on in red when no power is supplied to the unit.

(Nellcor)

(Nellcor)

Interference Indicates that interference exists. Pulse search Indicates that no pulse is detected. Fast response mode indicator Indicates that the response mode of the pulse oximeter is set to “Fast.” SatSeconds display Displays the selected SatSeconds alarm limit setting. Press Indicates that the lock function will be released when the key with this symbol is pressed. No humidified oxygen Indicates that humidified oxygen must not be supplied. Oxygen supply port 1 Indicates the oxygen supply port when oxygen is supplied through the flowmeter. Oxygen supply port 2 Indicates the oxygen supply port for the piping connecting hose when the oxygen controller is used. Do not immerse Indicates that the humidity chamber must not be immersed in water.

5

Precautions on Jamming

The unit is intended for use in hospitals. Portable and mobile communication equipment and other devices which generate high frequency should be used at least 30cm away from the unit, including cables specified by the manufacturer. Failure to do so may cause malfunction. Note: The emission characteristics of this unit make it suitable for use in industrial areas or hospitals (CISPR11 Class A). Take care when using the unit in residential environments (normally CISPR11 Class B), as it may not provide adequate protection from wireless frequency communication services. The user may also need to relocate or realign the unit to alleviate the problem.

Responsibility for Care of Equipment

It is the user (a hospital, a doctor’s office, a clinic) that is responsible for the operation, maintenance and care of the electric equipment for medical use. The equipment should be used only by medical personnel.

Prohibition of Modification

Do not disassemble or modify the unit. Otherwise, a fire, an electric shock or injury may result.

Periodical Inspection

Proper periodical inspection is needed to use the unit in the optimum condition.

In Case of Trouble

If any abnormal condition or trouble should occur to the unit, indicate on the unit that it is out of order and contact your local Atom representative or service engineer immediately. If any abnormal condition or trouble should occur, do not use the unit until it has been repaired completely by a service engineer so as to prevent possible danger.

7



Contents INTRODUCTION... 1

5-1-1.

Displaying and Setting the Incubator Air Temperature (Manual Control)... 44 5-1-2. Setting the Incubator Air Temperature in the Override Mode... 46 5-2. Placing the Infant in the Incubator... 47 5-3. Skin Temperature Monitoring... 48 5-3-1. Skin Temperature Monitoring... 48 5-3-2. Monitoring the Skin Temperature at Two Different Sites... 50 5-4. Setting the Skin Temperature (Servo Control)... 51 5-4-1. Preparation... 52 5-4-2. Placing the Infant in the Incubator... 52 5-4-3. Attaching the Skin Temperature Probe . ... 52 5-4-4. Setting the Servo Control Mode... 54

PLEASE READ WITHOUT FAIL [1]

[2]

Operating Precautions... 10 1-1.

DANGER... 10

1-2.

WARNING... 11

1-3.

CAUTION... 14

Parts Identification... 16 2-1. Main body... 16 2-2. Display... 19

PREPARATION [3]

Preparation before Use... 20 3-1. Assembly... 20 3-1-1. Attaching the Display to the Function Rail... 20 3-1-2. Connecting the Display to the Incubator... 20 3-1-3. Attaching the Filter... 21 3-2. Where to Install the Incubator... 21 3-3. Locking the Casters... 21 3-4. Power Outlet and Grounding... 22 3-5. Power Cord and Power Switch... 22 3-6. Adjusting the Hi-Low Stand... 23 3-7. Power Failure Alarm... 24 3-8. Daily Inspection... 24

OPERATION [4]

[6]

Incubator Air Temperature/Skin Temperature Control and Placing the Infant in the Incubator... 43 5-1. Setting the Incubator Air Temperature (Manual Control)... 43

Humidity Control... 56 6-1. Setting the Relative Humidity... 56

[7]

Oxygen Supply... 60 7-1. Using the Oxygen Flowmeter... 61 7-2. Using the Internal Oxygen Controller... 62 7-3. Oxygen Control (Oxygen Controller)... 63 7-3-1. Enabling the Oxygen Controller Function... 63 7-3-2. Calibrating the Oxygen Sensor... 64 7-3-3. Setting the Oxygen Concentration... 64

[8]

Pulse Oximeter... 65 8-1. Attaching the Sensor... 65 8-2. Connecting the Patient Cable to the Main Body... 66 8-3. Setting the Pulse Oximeter Upper/Lower Alarm Limits (SpO2, Pulse Rate)... 67 8-3-1. Setting the SpO2 Upper/Lower Alarm Limits... 67 8-3-2. Setting the Pulse Rate Upper/Lower Alarm Limits... 68

Display Screens... 25 4-1. General Description and Switching of the Screens... 25 4-1-1. General Description of the Screens... 25 4-1-2. Screen Transition Diagram... 27 4-2. List of Operations Available on Each Screen... 28 4-3. Main screen... 28 4-4. Pulse Oximeter Screen... 31 4-5. Weight Screen... 35 4-6. Menu Screen... 37 4-7. Trend Screen... 41

[5]

5-4-5. Setting the Skin Temperature in the Override Mode... 54

[9]

Weight Monitor... 69 9-1. 9-2. 9-3. 9-4.

Weighing the Infant... 70 Weight Trend Graph... 72 Switching the Unit of Weight... 73 Error Messages of the Weight Monitor... 73

[10] Other Operation Procedures... 74 10-1. Advanced Settings (How to Operate the Menu Screen)... 74

[12] Maintenance Inspection... 95

[13] Alarms... 104 [14] Troubleshooting... 109

APPENDIX

12-1. Inspection before Use... 96 12-2. Quarterly Inspection... 97 12-3. Periodical Replacement Parts... 98 12-4. Replacing the Filter... 99 12-5. Replacing the Oxygen Sensor... 100 12-6. Inspection Checklist... 102 12-7. Disposal... 103

MAINTENANCE

11-1. Hood Assembly... 88 11-2. Mattress Platform and Parts Beneath... 90 11-3. Humidity Chamber... 93 11-4. Others... 94

15-1. Technical Data... 111 15-2. EMC Level and Classification... 116

OPERATION

[11] Cleaning and Disinfection... 87

[15] Technical Information... 111

PREPARATION

MAINTENANCE

APPENDIX

PLEASE READ WITHOUT FAIL

10-1-1. Deleting Trend Data... 76 10-1-2. Deleting Weight Data... 76 10-1-3. Setting the Trend Period... 76 10-1-4. Switching the Skin Temperature 2 Display... 77 10-1-5. Switching the Unit of Temperature... 77 10-1-6. Setting the LCD Screen Brightness... 78 10-1-7. Setting the Light Sensor Level... 78 10-1-8. Setting the Alarm Volume... 79 10-1-9. Setting the Clock... 79 10-1-10.Checking How Many Hours the Filter Has Been Used... 80 10-1-11. Checking How Many Days the Oxygen Sensors Have Been Used... 80 10-1-12.Locking the Hi-Low stand... 80 10-1-13.Setting the Synchronizing Pulse Beep . ... 81 10-1-14.Setting the Sensitivity Mode... 81 10-1-15.Setting the Averaging Time... 82 10-1-16.Setting the FastSat... 82 10-1-17. Setting the SatSeconds... 83 10-1-18.Setting the Response Mode... 83 10-2. Drawing out the Mattress Platform... 84 10-3. Tilting the Mattress Platform... 84 10-4. X-ray Cassette Tray... 85 10-5. Letting Cords and Tubes into or out of the Incubator... 86 10-6. I/O Port... 86

Operating Precautions

[1] Operating Precautions Please follow the operating instructions described in this Manual for the safe use of the unit. The unit should be operated only by those who have been trained and instructed properly in its operation. The unit should be operated only for its intended use.

1-1.

DANGER

Death or serious injury, damage to equipment or a fire will result if the instructions given below are not followed. Only those who have been trained properly should operate the unit. Be sure to keep the admittance panels and the access ports closed when the unit is in use. Using the unit with an admittance panel or an access port left open may cause the infant to fall out of the baby compartment. Be sure to close the admittance panels and the access ports when performing phototherapy on an infant inside the incubator. Monitor the infant’s skin temperature when operating the unit. If the incubator air temperature should rise during phototherapy, proceed with the phototherapy after placing the infant in a cot or an open-type incubator (an infant warmer), as directed by the doctor. Since a mature infant emits much heat, the incubator air temperature may rise if you place the infant in the incubator and perform phototherapy. The incubator air temperature may also rise if you use multiple phototherapy units at the same time or if the room temperature is high. In such a case, proceed with the phototherapy after placing the infant in a cot or an open-type incubator, as directed by the doctor. Take sufficient care when using a cot, as it becomes difficult to observe the infant. Alternatively, placing an ice bag inside the incubator has the effect of decreasing the incubator air temperature. However, be sure to close the admittance panels and the access ports in this case also. Do not leave the unit unattended when an admittance panel or an access port is open. If an admittance panel or an access port is left open, the infant may fall out of the baby compartment and get fatally injured. Never leave the unit unattended when an admittance panel or an access port is open. Stop using the unit immediately and seek repair if an admittance panel, a snap-open access port or a press lever should be found loose or faulty in any way. The infant may fall out of the baby compartment. Never place a body warmer or any other possible ignition source in or near the unit. Use of oxygen will increase the risk of explosion or fire. Body warmers or other devices in which fire is used or which will generate a spark may cause an explosion or a fire if used near the unit. Do not use the unit in the presence of a flammable anesthetic gas. The unit may cause an explosion or a fire if used in the presence of such a gas. Do not use ether, alcohol or any other ignitable substance. Even a small amount of ether, alcohol or other ignitable substances may cause a fire when mixed with the oxygen in the incubator. 10

Operating Precautions

PLEASE READ WITHOUT FAIL

Ground the unit securely. Otherwise, a leakage current may cause an electric shock. In order to complete the ground connection, connect the power cord only to a properly grounded 3P power outlet including a ground terminal. Do not operate the unit if you have any doubt about its ground connection. Do not use a device generating high frequency near the unit. To prevent malfunction of the unit due to jamming, do not use electric surgical knives, portable and mobile communication equipment and other devices which generate high frequency near the unit during its operation. Analyze arterial gas levels repeatedly when a high oxygen environment is required. When the infant requires a high oxygen environment, it is extremely important and essential to periodically analyze arterial gas levels in order to maintain the desired oxygen concentration in the incubator. Follow the doctor’s instructions in measuring the oxygen concentration because ignoring essential requirements may increase the risk of retinopathy of prematurity and other adverse effects. Do not give a shock to the unit or let it hit anything. The screws or fixed parts may become loose.

1-2.

WARNING

Death or serious injury due to a fire or an electric shock will result if the instructions given below are not followed. Be sure to follow the doctor’s instructions in setting the incubator air temperature or the infant’s skin temperature. Be sure to follow the doctor’s instructions in setting the relative humidity in the incubator. Be sure to follow the doctor’s instructions in supplying oxygen. Be sure to follow the doctor’s instructions in setting the oxygen concentration in the incubator. Use only oxygen for medical use. Be sure to bear in mind the following precautions during oxygen supply. •D  o not place a body warmer, a flashlight, oils and fats, or flammable vaporizable matters in the incubator. •U  se pure cotton for the infant’s clothing, bed sheets, etc. Do not use any material that is easily charged with static electricity. •U  se pure cotton or fire-proof materials for the clothing of doctors, nurses and ambulance staff who handle this unit. Bear in mind the following precautions while using oxygen supply equipment. • I f oil, grease or a grease-like substance should get in contact with pressurized oxygen, a violent spontaneous ignition may occur. Do not let such substances stick to the oxygen pressure regulator, the oxygen cylinder valve, piping, connections and other parts of oxygen supply equipment. 11

Operating Precautions

• On a high-pressure oxygen cylinder, use only a tested pressure reducing valve or pressure regulating valve indicated specifically for oxygen supply. Do not use such a valve for any gas other than air or oxygen. It is dangerous to use a valve to supply a gas other than air or oxygen and then to supply oxygen again. If the oxygen sensor should break or get damaged, the electrolyte inside may leak out of the sensor. If you should come in contact with the electrolyte, wash it away immediately and thoroughly with copious amounts of water. Smoking is prohibited in the room where the unit is installed. Do not place any possible ignition sources in the room. Take care of the usage environment. Using the unit in a strong electromagnetic environment may disrupt control over temperature, humidity and oxygen, or prevent accurate measurement values from being displayed. Do not use the unit next to other devices. Using the unit next to or stacked with other devices may cause malfunction. When it is unavoidable to do so, it is necessary to check that the unit and the other devices are operating correctly. Avoid damaging the power cord. A damaged power cord may cause a fire or an electric shock. • Do not get the power cord caught between the unit and the wall, a shelf or the floor. • Do not place the power cord near a heating apparatus or heat it. • Do not put anything heavy on the power cord. • Always grasp the power plug with your hand to remove the power cord from the power outlet. A damaged power cord should be replaced immediately with a new one. Use only the power cord supplied with the unit. Otherwise, a fire or an electric shock may result. A power cord or an AC adapter other than the one supplied with the unit can generate high frequency noise and cause jamming to other electric devices for medical use and thus result in malfunction, or make the unit more susceptible to high frequency noise emitted by other electrical devices and thus result in malfunction. Before cleaning and disinfecting the unit, be sure to turn the power switch off, remove the power plug, and allow the incubator air temperature and the heater temperature to drop sufficiently. Do not touch the power plug with a wet hand. Touching the power plug with a wet hand may cause an electric shock. Do not touch the heaters during use or shortly after use. The heaters are so hot during use and shortly after use that you may get burned. Allow the heaters to cool down sufficiently before touching them. Do not disassemble or modify the unit. Disassembling or modifying the unit may cause a fire, an electric shock or injury. Do not install the unit where it will be exposed to excessive humidity, dust or steam. Installing the unit in such a place may cause a fire or an electric shock. 12

Operating Precautions

PLEASE READ WITHOUT FAIL

The power outlet should be located near the unit to prevent accidental contact with a trailing power cord. Use a separate power outlet for each unit. Do not put many loads on one power outlet. In order to complete the ground connection, connect the power cord only to a properly grounded 3P power outlet including a ground terminal. Do not operate the unit if you have any doubt about its ground connection. Ground peripheral electric equipment securely. The electrical rating of this unit is as follows: AC230V; power consumption 600VA; frequency 50/60Hz; operating voltage range AC230V±10% Do not connect the unit to any other power source. The unit should be serviced only by qualified personnel. Be sure to inspect the unit at the start of each day. Operating the unit without inspecting it at the start of each day may let a defect pass unnoticed and cause a potentially unfavorable outcome. The doctor is responsible for making a decision on transporting a premature infant. Watch the infant continuously during transport. Transporting a premature infant is associated with a risk of intracerebral hemorrhage due to jolting during transport. Check for conformity to the applicable standard if the unit is going to be connected to another medical device for use as a system. Accessory equipment connected to the analogue and digital interfaces must comply with the relevant IEC standards (e.g. IEC 60950 for data processing equipment). Furthermore all configurations should comply with IEC 60601-1. But the items that are not specified as part of the system should not be connected. Anybody who connects additional equipment to the signal input or signal output configures a medical system, and therefore should make the medical system comply with the requirements of 60601-1 on his or her own responsibility. If in doubt, consult your local Atom representative. During transport, set the incubator to the lowest level. If not set to the lowest level, injury or damages may result when the incubator loses balance while being moved and hits a surrounding object, or falls down. Use the unit on a flat and stable surface. Placing the unit on a surface tilted over 10 degrees or on an unstable location may cause it to fall down.

13

Operating Precautions

1-3.

CAUTION

Injury or damage to surrounding objects may result if the instructions given below are not followed. Be sure to clean and disinfect the unit before using it for the first time after purchase. The unit is shipped without being disinfected. During standby, be sure to always preheat the unit in order to keep the incubator air temperature stable. Place the infant in the incubator only after the incubator air temperature has stabilized. When feeding the cords and tubes into the unit, be very careful not to let them wind or tighten around the patient. Do not twist or pull the cords by force. If any defect should be found, ask an expert for repair without attempting to repair it yourself. Remove the power plug from the power outlet before moving the unit to another place or when the unit is not going to be used for a long time. Moving the unit to another place with the power plug connected to the power outlet will damage the power cord and may cause a fire or an electric shock. Remove the power plug from the power outlet before cleaning and disinfecting the unit. Cleaning and disinfecting the unit with the power plug connected to the power outlet may cause an electric shock. Install the unit out of reach of small children. When performing phototherapy on the infant in the incubator, pay special attention to the infant’s skin temperature and the incubator air temperature during the treatment. The infant’s skin temperature and the incubator air temperature may rise due to the radiant heat generated by the phototherapy unit. Do not install the unit in direct sunlight or near a heating apparatus. Do not expose the unit to extraordinarily high temperature or excessive humidity. Do not place anything heavy on the unit. Do not press strongly or rub the operation panel of the display. Pressing it strongly or rubbing it may damage the display or cause it to malfunction. Be careful not to let any medical fluid adhere to the display. Do not attach any peripheral device that is not specified by Atom to the incubator.

14

Operating Precautions

PLEASE READ WITHOUT FAIL

Check the operation of the peripheral devices. If a device transmitting or receiving weak signals is installed near the unit, it may be affected by the electromagnetic waves generated by the latter. Check the operation of the peripheral devices for any effect before using the unit in clinical settings. Stop using the unit immediately if any trouble is detected. When relocating the unit, watch your step so that you do not have your feet run over by a caster. Do not put your hand on an admittance panel when transporting the unit. Pressing an admittance panel strongly may break it. At least two people are required to transport the unit by holding the main body. Watch out for any obstacles during transport. If a peripheral device is attached to the main body, the unit may hit surrounding objects and get damaged or broken. When taking radiographs with the supplied X-ray cassette tray, read the instruction manuals for the radiation device, and make sure that necessary protection measures are taken.

15

Parts Identification

[2] Parts Identification 2-1.

Main body

No. Name ① Display ② Dovetail rail ③ Iris access port ④ Sensor module ⑤ Admittance panel operating lever ⑥ Snap-open access port ⑦ Admittance panel ⑧ Mattress platform tilting knob Note: ⑫ Drawer is an available option.

16

No. ⑨ ⑩ ⑪ ⑫ ⑬ ⑭ ⑮ ⑯

Name X-ray cassette tray door locking knob Foot switch Caster Drawer Humidity chamber cover Mattress Tube introduction slit packing Admittance panel operating knob

Parts Identification

PLEASE READ WITHOUT FAIL

◾◾ Rear ⑰ ⑱ ⑲ ⑳

 

 

   

No. ⑰ ⑱ ⑲ ⑳  

Name Skin temperature probe connecting port 1 Skin temperature probe connecting port 2 Power switch Connector for sensor module Filter cover Oxygen supply port 1

No.      

Name Oxygen supply port 2 Connector for weight monitor Connector for the display Connector for the Power Pack i (UPS) AC inlet Connector for SpO2

Note:  Oxygen supply port 2 is available only on the unit equipped with the oxygen controller.  Connector for SpO2 is an available option.

17

Parts Identification

◾◾ Inside ㉛ ㊵ ㉜ ㉙

㊶

㊴ ㉝

㉚

㉚ ㉞

㉟ ㊱

㊲

㊳

No.             

Name Mattress platform X-ray cassette tray Weight monitor unit Mattress platform for weight monitor Tray for weight monitor Mattress platform tray Middle board Fan cover Heater Fan Baby guard Tube introduction slit packing Weight monitor module

Note:  Weight monitor unit is an available option.

18

Parts Identification

Display

PLEASE READ WITHOUT FAIL

2-2.

◼ Front

◼ Bottom

No. ① ② ③ ④ ⑤ ⑥

◼ Rear

Name Alarm lamp Power failure alarm indicator Operation panel I/O port (External communication connector) Connector for the main body Communication port (LAN)

19

Preparation before Use

[3] Preparation before Use 3-1.

Assembly

3-1-1.

Attaching the Display to the Function Rail

(1)

Loosen the thumbscrew of the function rail attachment.

(2)

Insert the clawed end of the function rail attachment into the groove of the function rail. Tighten the thumbscrew and fix the function rail attachment to the function rail. After tightening the thumbscrew, make sure that the surface of the swing portion is aligned with the surface of the function rail attachment.

Display

Thumb screw Function rail attachment

Before tightening the thumbscrew Function rail attachment

●● When fixing the function rail attachment, be careful not to apply excessive force to the cable, twist the cable or get it caught. ●● Before fixing the function rail attachment, adjust the position of the display to ensure optimum viewing.

3-1-2. (1)

After tightening the thumbscrew Swing portion Thumbscrew

Connecting the Display to the Incubator Connect the display to the incubator. ① Insert the connector of the display connecting cable into the connector for the main body on the rear of the display. After insertion, tighten the two knobs on the connector. Then, pull the cable lightly to make sure that the connector does not come off. ② Insert the connector on the other end of the cable into the connector for the display on the main body of the incubator. After insertion, tighten the two knobs on the connector. Then, pull the cable lightly to make sure that the connector does not come off.

Connector for the main body

Connector

Knobs

Connector for the display

Connector

●● When inserting or removing the connector, be careful not to pull the cable by force or twist it.

20