macro-Line sagittal saw handpiece GB125R

Note Mechanical reprocessing should be favored over manual cleaning as it gives better and more reliable results. Note Successful processing of this medical device can only be ensured if the processing method is first validated. The operator/sterile processing technician is responsible for this. The recommended chemistry was used for validation. Note If there is no final sterilization, then a virucidal disinfectant must be used. Note For the latest information on reprocessing and material compatibility see also the Aesculap extranet at www.extranet.bbraun.com The validated steam sterilization procedure was carried out in the Aesculap sterile container system.

6.2

General information

Dried or affixed surgical residues can make cleaning more difficult or ineffective and lead to corrosion. Therefore the time interval between application and processing should not exceed 6 h; also, neither fixating pre-cleaning temperatures >45 °C nor fixating disinfecting agents (active ingredient: aldehydes/alcohols) should be used. Excessive measures of neutralizing agents or basic cleaners may result in a chemical attack and/or to fading and the laser marking becoming unreadable visually or by machine for stainless steel. Residues containing chlorine or chlorides e.g. in surgical residues, medicines, saline solutions and in the service water used for cleaning, disinfection and sterilization will cause corrosion damage (pitting, stress corrosion) and result in the destruction of stainless steel products. These must be removed by rinsing thoroughly with demineralized water and then drying. Additional drying, if necessary. Only process chemicals that have been tested and approved (e.g. VAH or FDA approval or CE mark) and which are compatible with the product’s materials according to the chemical manufacturers’ recommendations may be used for processing the product. All the chemical manufacturer's application specifications must be strictly observed. Failure to do so can result in the following problems: ■ Optical changes of materials, e.g. fading or discoloration of titanium or aluminum. For aluminum, the application/process solution only needs to be of pH >8 to cause visible surface changes. ■ Material damage such as corrosion, cracks, fracturing, premature aging or swelling. ► Do not use metal cleaning brushes or other abrasives that would damage the product surfaces and could cause corrosion. ► Further detailed advice on hygienically safe and material-/value-preserving reprocessing can be found at www.ak-i.org, link to Publications, Red Brochure – Proper maintenance of instruments.

6.3

Dismantling prior to carrying out the reprocessing procedure

► Disassemble the product immediately after use, as described in the respective instructions for use.

6.4

Preparations at the place of use

► Remove any visible surgical residues to the extent possible with a damp, lint-free cloth. ► Transport the dry product in a sealed waste container for cleaning and disinfection within 6 hours.

6.5

Phase

Step

T [°C/°F]

t [min]

Conc. [%]

Water quality

Chemical

I

Cleaning

RT (cold)

-

-

D–W

-

II

Drying

RT

-

-

-

-

III

Wipe disinfection

-

>1

-

-

Meliseptol HBV wipes 50 % Propan-1-ol

IV

Final rinse

RT (cold)

0.5

-

FD-W

-

V

Drying

RT

-

-

-

-

D–W: FD–W:

Drinking water Fully desalinated water (demineralized, low microbiological contamination: drinking water quality at least) Room temperature

RT:

Phase I ► Clean the product under running faucet water, using a suitable cleaning brush until all visible residues have been removed from the surfaces. ► Mobilize non-rigid components, such as set screws, links, etc. during cleaning. Phase II ► Dry the product in the drying phase with suitable equipment (e.g. cloth, compressed air), see Validated cleaning and disinfection procedure. Phase III ► Wipe all surfaces of the product with a single-use disinfectant wipe. Phase IV ► After the specified exposure time (at least 1 min), rinse the disinfected surfaces under running FD water. ► Drain any remaining water fully. Phase V ► Dry the product in the drying phase with suitable equipment (e.g. cloth, compressed air), see Validated cleaning and disinfection procedure.

6.8

Inspection, maintenance and checks

► Allow the product to cool down to room temperature. ► Inspect the product after each cleaning and disinfecting cycle to be sure it is: clean, functional, and undamaged. ► Check the product for any damage, abnormal running noise, overheating or excessive vibration. ► Inspect tools for broken, damaged or blunt edges. ► Set aside the product if it is damaged.

Preparation before cleaning 6.9

► Carry out non-fixating/NaCl-free pre-cleaning immediately after use.

6.6

Manual cleaning and wipe disinfecting

Cleaning/disinfection

Product-specific safety instructions for the reprocessing procedure Damage to, or destruction of the product caused by mechanical cleaning/disinfection! ► Only clean and disinfect the product manually. CAUTION

Packaging

► Always observe the instructions for use of packaging and storage devices. ► Place the product on a tray in such a way that it is protected against damage. ► Pack trays appropriately for the sterilization process (e.g. in Aesculap sterile containers). ► Ensure that the packaging will prevent a recontamination of the product.

6.10 Steam sterilization ► Prior to sterilization, remove any tools and adapters and uncouple the handpiece from the motor unit. ► Check to ensure that the sterilizing agent will come into contact with all external and internal surfaces (e.g. by

opening any valves and faucets). ► Validated sterilization process

Damage to the product due to inappropriate cleaning/disinfecting agents! ► Only use cleaning/disinfecting agents approved for surface cleaning. Follow the manufacturer’s instructions for the respective cleaning/disinfecting agent. CAUTION Damage to the product due to inappropriate cleaning/disinfecting agents and/or excessive temperatures! ► Use cleaning and disinfecting agents according to the manufacturer’s instructions which – be approved for plastic material and high-grade steel, – do not attack softeners (e.g. in silicone). ► Observe specifications regarding concentration, temperature and exposure time.

CAUTION

– Disassemble the instrument – Steam sterilization through fractionated vacuum process – Steam sterilizer according to DIN EN 285 and validated according to DIN EN ISO 17665 – Sterilization using fractionated vacuum process at 134 °C/holding time 5 min ► When sterilizing several instruments at the same time in a steam sterilizer, ensure that the maximum load capacity of the steam sterilizer specified by the manufacturer is not exceeded.

6.11 Storage ► Store sterile products in germ-proof packaging, protected from dust, in a dry, dark, temperature-controlled area.

7.

Maintenance

To ensure reliable operation, the product must be maintained at least once a year. For technical service, please contact your national B. Braun/Aesculap agency, see Technical Service.

► Dry the product for at least 10 minutes at a maximum of 120 °C.

Note The indicated drying temperature is a guide temperature only. It must be checked taking into account the specific conditions (e.g. load) and adjusted if applicable. ► Do not clean motors/handpieces by ultrasonic treatment and do not immerse them in any liquids. To avoid the

risk of corrosion/malfunctioning, allow any fluid that has entered the product to drain out immediately.

8.

Troubleshooting list

Malfunction

Detection

Cause

Remedy

Excessive noise

Motor unit can be pulled out from handpiece

Motor unit not coupled correctly

Couple the motor unit, see Coupling a motor unit

Handpiece hot

Worn gearing

Have product repaired by the manufacturer

Lack of power at handpiece

Excessive noise

Worn gearing

Have product repaired by the manufacturer

Insufficient cutting power of saw blades

Saw blade worn

Saw blade blunt

Replace saw blade

Motor unit not running correctly

-

Observe the instructions for use of the motor unit

Saw blade hot

Inadequate chip removal

Back and forth movement during sawing

Coupling parts broken

Coupling defective

Have product repaired by the manufacturer

Motor unit running, but not powering the handpiece

Defective gearing

Have product repaired by the manufacturer

Validated cleaning and disinfection procedure Validated procedure

Special features

Reference

Manual cleaning and wipe disinfection

■ When cleaning instruments with movable

Chapter Manual cleaning/disinfecting and subsection:

hinges, ensure that these are in an open position and, if applicable, move the joint while cleaning.

■ Drying phase: Use a lint-free cloth or com-

■ Chapter Manual cleaning and wipe disinfecting

pressed air for medical purposes

■ Ensure that the product is positioned in such a way that water will not enter the product, e.g., through coupling interfaces. (Immediately remove any fluid that entered the product inadvertently.)

6.7

Manual cleaning/disinfecting

► Prior to manual disinfecting, allow water to drip off for a sufficient length of time to prevent dilution of the dis-

infecting solution. ► After manual cleaning/disinfection, check visible surfaces visually for residues. ► Repeat the cleaning/disinfection process if necessary.

Saw blade not moving

9.

Technical Service Risk of injury and/or malfunction! ► Do not modify the product. WARNING

► For service and repairs, please contact your national B. Braun/Aesculapp agency.

Modifications carried out on medical technical equipment may result in loss of guarantee/warranty rights and forfeiture of applicable licenses. Service addresses Aesculap Technischer Service Am Aesculap-Platz 78532 Tuttlingen / Germany Phone: +49 (7461) 95 -1601 Fax: +49 (7461) 14 -939 E-Mail: [email protected] Other service addresses can be obtained from the address indicated above.

10.

Accessories/Spare parts

Art. no.

Designation

GA059

STERILIT Power Systems drip lubricator

GA156

Motor unit: flexible shaft

GA172 GA200

AIRLAN pneumatic motor

GA222R

Spray nozzle

GB020R

Hexagon wrench

GB125/804

Nut

GC530–GC534

Saw blades

GC540–GC543 GC670

11.

Technical data

Classification acc. to Directive 93/42/EEC Art. no.

Designation

Class

GB125R

macro-Line sagittal saw handpiece GB125R

IIa

Designation

Value

Size

120 mm x 30 mm x 30 mm

Weight

420 g

Maximum motor unit speed

20 000 rpm

Ratio Rotation to oscillation

1:1

Saw blade adapter

Star coupling

Suitable for sterilization

up to 143 °C (3 bar)

12.

Disposal

Note The user institution is obliged to process the product before its disposal, see Validated reprocessing procedure. ► Detailed information concerning the disposal of the product is available through your national B. Braun/Aesculap

agency, see Technical Service. TA-Nr. 005327

01/14

V6

Änd.-Nr. 48673