Radiance 19'' Users Instructions Rev C

Table of Contents Tab 1 Safety Considerations ---------------------------------------------------------------------------- ii Declaration of Conformity ----------------------------------------------------------------------iii Limited Warranty ---------------------------------------------------------------------------------iii Tab 2 About This Manual --------------------------------------------------------------------------------1 Quick Startup---------------------------------------------------------------------------------------1 Powering On The Unit -------------------------------------------------------------------------1 First Time Users and Initial Test--------------------------------------------------------------1 Tab 3 Connector Panels ----------------------------------------------------------------------------------2 Display Mounting to Base -----------------------------------------------------------------------3 Tab 4 Control ----------------------------------------------------------------------------------------------4 Image Adjustments --------------------------------------------------------------------------------4 Brightness ----------------------------------------------------------------------------------------4 Contrast ------------------------------------------------------------------------------------------4 Backlight -----------------------------------------------------------------------------------------4 Tab 5 Menu Systems Overview -------------------------------------------------------------------------5 Video Source ---------------------------------------------------------------------------------------6 GPIO ------------------------------------------------------------------------------------------------6 Display Set Up -------------------------------------------------------------------------------------7 SD-SDI Picture Menu --------------------------------------------------------------------------7 S-Video Picture Menu--------------------------------------------------------------------------7 Composite Picture Menu -----------------------------------------------------------------------7 VGA / SOG Picture Menu ---------------------------------------------------------------------8 RGBS / YPbPr Picture Menu -----------------------------------------------------------------8 DVI-Digital Picture Menu ---------------------------------------------------------------------9 HD-SDI Picture Menu -------------------------------------------------------------------------9 Color Menus ----------------------------------------------------------------------------------- 10 Setup Menu ------------------------------------------------------------------------------------ 11 Defaults Menu --------------------------------------------------------------------------------- 12 Tab 6 Troubleshooting --------------------------------------------------------------------------------- 13 Tab 7 Drawing and Dimensions ----------------------------------------------------------------------- 14 Tab 8 Data Connectors and Pin Outs ----------------------------------------------------------------- 15 GPIO Connectors and Pin Outs ---------------------------------------------------------------- 16 Power Connector and Pin Out ----------------------------------------------------------------- 16 24 Volt Extension Cable ------------------------------------------------------------------------ 16 Tab 9 Specifications ------------------------------------------------------------------------------------ 17 Video Inputs -------------------------------------------------------------------------------------- 18 Video Formats ----------------------------------------------------------------------------------- 18 Proprietary Notice and Liability Disclaimer ------------------------------------------------- 18 Cleaning Instructions---------------------------------------------------------------------------- 18 Contact -------------------------------------------------------------------------------------------- 19

i

1 CAUTION This symbol alerts the user that important literature concerning the operation of this unit has been included. Therefore, it should be read carefully in order to avoid potential problems.

This symbol warns user that un-insulated voltage within the unit may have sufficient magnitude to cause electrical shock. Therefore, it is dangerous to make contact with any part inside the unit. To reduce the risk of electric shock, DO NOT remove cover (or back). There are no user serviceable parts inside. Refer servicing to qualified service personnel. To prevent fire or shock hazards, do not expose this unit to rain or moisture. Also, do not use this unit's polarized plug with an extension cord receptacle or other outlets unless the prongs can be fully inserted. The display is designed to meet the medical safety requirements for a patient vicinity device. This device may not be used in connection with life support equipment.

Underwriters Laboratories (UL) Classification: UL Safety Compliance: This LCD monitor is U.L. Classified WITH RESPECT TO ELECTRIC SHOCK, FIRE AND MECHANICAL HAZARDS ONLY IN ACCORDANCE WITH UL 60601-1/CAN/CSA C22.2 NO. 601.1. EEC Safety Compliance: This display unit meets the requirements of EN-60601-1 so as to conform to the Medical Device Directive 93/42/EEC (general safety information).

DEMKO EN 60601-1

This monitor complies to the above standards only when used with the supplied medical grade power supply. 24 Volt: Ault MW116KA2400F02 The monitor should be powered from a center tapped circuit when used in the US at voltages over 120 volts. Monitor is intended for continuous operation. This display is energized from an external electrical power source for class 1 equipment. It is the responsibility of the installer to test the display’s earth ground to verify that it complies with the hospital, local and national impedance requirements. A ground post, located on the back of the display, may be used for the purpose of grounding the display’s chassis. Any such ground must be installed in accordance with applicable electrical codes. The ground post is shown on the mechanical drawing found on page 2. This equipment may not be used in the presence of flammable anesthetics mixture with air, oxygen or nitrous oxide.

Recycling: Follow local governing ordinances and recycling plans regarding the recycling or disposal of this equipment. ii

Declarations of Conformity FCC and Council Directives of European Standards: This device complies with Part 15 of FCC rules and 93/42/EEC of the Council Directives of European Standards. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesirable results. 1. Use the attached specified cables with the color monitor so as not to interfere with radio and television reception. Use of other cable and adapters may cause interference with other electronic equipment. 2. This equipment has been tested and found to comply with the limits pursuant to FCC part 15 and CISPR 11. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. IEC: This equipment has been tested and found to comply with the limits for medical devices to the IEC 60601-1-2:2001. These limits are designed to provide reasonable protection against harmful interference in a typical medical installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to other devices in the vicinity. FCC, Council Directives of European Standards and IEC: There is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult your dealer or an experienced radio/TV technician for help. Accessory equipment connected to this monitor must be certified according to the respective IEC Standards (i.e., IEC 60950-1 for data processing equipment and IEC 60601-1 for medical equipment). Furthermore, all configurations shall comply with the system standard, IEC 60601-1-1. Anyone who connects additional equipment to the signal input part or signal output part configures a medical system, and is therefore responsible that the system complies with the requirements of system standard IEC 60601-1-1. Whoever is responsible for securing the monitor to a system needs to insure that the mounting equipment used with this display complies to IEC standard 60601-1. If in doubt, consult the technical services department or your local representative.

Limited Warranty National Display Systems, Inc. (hereinafter "NDS") warrants this product to be free from defects in material and workmanship and, subject to the conditions set forth below, agrees to repair or replace any part of the enclosed unit other than the LCD backlight, which proves defective for a period of three (3) years from the date of first purchase or 10,000 hours of operation whichever comes first. Spare parts are warranted for ninety (90) days. This warranty is limited to the original purchaser of the product and is not transferable. This warranty covers only NDS supplied components. Service required as a result of third party components is not covered under this warranty. Proof of Purchase will be required by NDS to substantiate date of purchase. Such proof of purchase must be an original bill of sale or receipt containing the name and address of the seller and the purchaser and the serial number of the product. It shall be your obligation and expense to have the product shipped, freight prepaid, or delivered to the authorized reseller from whom it was purchased, or other facility authorized by NDS to render services provided hereunder, in the original package. All products returned to NDS for service MUST have prior approval which may be obtained by contacting the factory. The product shall not have been previously altered, repaired, opened or serviced by anyone other than a service facility authorized by NDS to render such service. The serial number of the product shall not have been altered or removed. In order to be covered by this warranty, the product shall not have been subjected to displaying of fixed images for long periods of time, resulting in image persistence (afterimage effects), accident, misuse or abuse or operation contrary to the instructions contained in the User's Manual. Any such conditions will void this warranty. NDS SHALL NOT BE LIABLE FOR DIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL OR OTHER TYPES OF DAMAGES RESULTING FROM THE USE OF ANY NDS PRODUCT OTHER THAN THE LIABILITY STATED ABOVE. THESE WARRANTIES ARE IN LIEU OF ALL OTHER WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. The product is warranted in accordance with the terms of this limited warranty. Consumers are cautioned that system configuration, software, the application, customer data and operator control of the system, among other factors, affect the product performance. While NDS products are considered to be compatible with many systems, specific functional implementation by the customers of the product may vary. Therefore, suitability of a product for a specific purpose or application must be determined by consumer and is not warranted by NDS.

iii

About This Manual

2

This manual is designed to assist the user with proper installation, setup and operation of the Radiance Medical LCD display. Depending on the model and options that were purchased, some of the features and options in this manual may not apply to the display you are using. A black tab number on the side of the page denotes the beginning of a section. The functional descriptions in this manual are representative of: Model Number: SC-SX19 Display Number 90R0001 Revision A and B. Firmware BIOS: 58B0172 Version B and later. Firmware BIOS: 58B0178 Version A and later. Model Number: SC-SX19 Display Number 90R0001 Revision C through E. Firmware BIOS: 58B0180 Version B and later. Firmware BIOS: 58B0190 Version B and later. High Definition SDI Support: Display Number 90R0001 Revision F and later. Firmware BIOS: 58B0213 Version A and later. Note: This BIOS supports both High Definition SDI (HD SDI) and Standard Definition SDI (SD SDI). Due to the technology utilized to manufacture flat-panel screens, characters will appear crisper with sharper edges than that of a computer CRT. For the same reason, live video may appear a little blocky. Users not familiar with the image differences should familiarize themselves before utilization in a critical application and determine its usability. For mission critical applications, we strongly recommend that a replacement unit be immediately available.

Quick Startup Powering On The Unit: Connect the power supply to the display via the power plug. Plug in the AC adapter. Connect the video source to the Radiance display. Apply power to the peripheral device, then to the display. The National Display Systems (NDS) logo is displayed, followed shortly by video. The electronics, designed by NDS, incorporates proprietary SmartSync™ technology which at initialization, examines the incoming signal and automatically displays the video image in its proper format. This eliminates making adjustments to most video sources. To fine tune the image, please refer to “Image Adjustments” on page 4.

First time users and initial test: Visually, Flat-Panel (LCD) images will look crisper than those of a traditional CRT. It is recommended that first time users view the display next to a CRT to familiarize themselves with any subtle differences in viewing quality.

1

Connector Panels Rev. C through E BIOS 58B0180, BIOS 58B0190 and Rev F and later BIOS 58B0213 90R0001 Rev. F and later accepts both SDI and HDSDI. 90R0001 Rev. C through E accepts SDI only.

3

Notes 1. An S-Video signal may be applied via 2 BNC terminated cables to the Y and C labeled BNC connectors or a DIN 4 terminated cable, but not both. 2. RGBS and YPbPr signals may be applied via the RGBS / YPbPr HD-15 connector or the R/Pr, G/Y, B/Pb and HS / C-SYNC BNC connectors. 3. A VGA signal may be applied via the VGA HD-15 connector or the R/Pr, G/Y, B/Pb, HS / C-SYNC and VS BNC connectors. 4. Set the REDRIVE switch to Off when the RGBS and YPbPr signals will not be daisy chained to another display. The REDRIVE switch is set to On when the RGBS and YPbPr signals will be daisy chained to a second display. 5. On some displays the Equipotentiality Conductor may be identified with this symbol:

Rev A and B BIOS 58B0172 and BIOS 58B0178

Notes 1. An S-Video signal may be applied via 2 BNC terminated cables to the Y and C labeled BNC connectors or a DIN 4 terminated cable, but not both. 2. RGBS and YPbPr signals may be applied via the HD-15 connector or the R/Pr, G/Y, B/Pb and CSYNC BNC connectors. If the RGBS signals are applied via the BNC connectors, then a 75 Ohm terminator (NDS Part Number: 55Z0001) must be inserted in the RGBS (HD-15) connector.

Electrical Symbols Equipotentiality: This symbol appears next to the display’s Potential Equalization Conductor. (ground post)

Open (Off) Switch: This symbol appears on the open, or off, side of the display’s rocker switch. Closed (On) Switch: This symbol appears on the closed, or on, side of the display’s rocker switch. 2

Display Mounting to Stand Attach the stand to the display using the four supplied thumbscrews. Note: Display Stand is an optional accessory. Order Part Number: 26B0063

3

Control The Radiance displays are controlled via a 6 button keypad. The keypad, located on the bottom front of the display, allows the user to make adjustments to various display parameters using the On Screen Menus (OSM) system.

4 Image Adjustments

Adjust Brightness Press the Brightness / Contrast button to display the Brightness control. Press the or button to increase or decrease brightness. Setting the brightness too high or too low will decrease the amount of visible grayscales.

Adjust Contrast Press the Brightness / Contrast button twice to display the Contrast control. Press the or button to adjust the contrast. Setting the contrast too high or too low causes loss of some grayscales. Color saturation may appear incorrect.

Adjust Backlight Press the Brightness / Contrast button three times to display the Backlight control. Press the or button to set the backlighting. Note: Lowering the backlight level will increase the backlight lifetime.

4

Menu Systems Overview Press the MENU button once to open the Menu System. The current video input and its resolution are shown in the Display Mode tab on the top right of the menu. The Menu System opens with Picture menu displayed. Press the or button to select the menu you want to work with, then press the SCROLL button to select the parameter. Press the or button to set the parameter to the desired value. Press the MENU button to save your changes and close the Menu System. Notes: 1. All parameter names change to the language selected in the Setup Menu. 2. Grayed out parameters are not accessible.

5

Language List: English Deutsch Francais Italiano Svensk Espanol Nederlands

5

Video Source Inputs Menu

When the display is powered on Auto Source Select looks at the previously selected video source first. If a signal is present it is displayed, otherwise Auto Source Select starts scanning the inputs for a signal. To switch to a different input source, press the INPUT button to open the input menu. The Input menu shows: selected to the right of the active input. Press the SCROLL button to highlight the desired input. Finally, press the button to select it. To select RGBS / YPbPr or Composite / SOG; Scroll to the RGBS / YPbPr or Composite / SOG input and press the button to select the input. Finally, press the button to toggle between RGBS / YPbPr or Composite / SOG. The inactive input is grayed out. BIOS 58B0213 Only: Connecting an HD SDI signal to the SDI connector causes the internal electronics to switch to HD SDI support. The resolution message (upper right corner of the menu) will show the resolution of SDI signal.

GPIO General Purpose Input Output (GPIO) Source Selection: GPIO source selection allows up to 6 inputs to be flagged for remote source switching. Note: If RGBS is selected as a GPIO source then YPbPr may not be selected as a GPIO source until RGBS has been de-selected. The same is true for the Composite / SOG inputs. GPIO Source Selection Setup: 1. Press the SCROLL button to highlight the first input to be designated. 2. Select it by pressing the button. 3. Press the the Brightness / Contrast button, the text turns green. 4. Repeat steps 1 and 2 for the next input. 5. To de-select an input, press the SCROLL button to highlight the input. 6. Select it by pressing the button. 7. Press the Brightness / Contrast button, the text turns black. Note: An input must be active in order to be selected or de-selected as a GPIO source. Using GPIO Source Selection: 1. Connect an appropriately wired fixture to the GPIO connector. 2. Press the fixture’s Source Select switch. 3. The display’s input switches to the next designated input. Inputs are selected in the order they appear in the Input Menu. 4. Each time the fixture’s Source Select button is pressed the display steps to the next designated input. 5. Press the fixture’s Source Select button until the desired input is selected. Note: GPIO connector pin out is on page 16. 6

Setting Up the Display SD- SDI Picture Menu

S-Video Picture Menu

Composite Picture Menu

Horizontal Position Moves the image to the left or right. Press

or

Vertical Position Moves the image up or down. Press

to vertically center the image.

Sharpness Press or

or

to horizontally center the image.

to adjust the sharpness (focus) of the displayed image.

Overscan off = Picture is displayed at the maximum size that will fit on the screen without losing video information. on = Stretches picture horizontally and vertically to fill the screen, but does not change its aspect ratio. Some video information may be lost. Picture may have black bars top and bottom or left and right. Select using or buttons. Video Format auto = Automatically sets the unit to the format of the connected video source. ntsc = Sets the unit to accept NTSC video. pal = Sets the unit to accept PAL video. Select using or buttons.

7

VGA / SOG Picture Menu

RGBS / YPbPr Picture Menu

Horizontal Position Moves the image to the left or right. Press

or

Vertical Position Moves the image up or down. Press

to vertically center the image.

or

to horizontally center the image.

Sharpness Press or to adjust the sharpness (focus) of the displayed image. Note: When the VGA input is active Sharpness cannot be adjusted when the display is operating at native resolution. Phase Press or

to adjust the phase of the display’s pixel clock.

Frequency Adjusts the frequency of the display’s pixel clock. With Scaling set to Fill adjust until image just fills the screen horizontally. Press or to adjust the frequency of the display’s pixel clock. Scaling (VGA and SOG) Fill = Expands the video image to fill the entire screen. The aspect ratio may not be accurately displayed. Aspect = Expands the video image until its largest dimension fills the screen. Image may be displayed with black bars on the top and bottom or the left and right. 1:1 = Displays the video data in its native size and aspect ratio. Image may be displayed with black bars on the top and bottom and on the left and right. Select using or buttons. SmartSync™ On initialization NDS’ proprietary SmartSync™ technology examines the incoming signal and automatically displays the video image in its proper format. To run select SmartSync™ and press the button. When the input is RGBS the resolution toggles from 737 x 464 to 720 x 480 or vice versa each time SmartSync™ is run. Overscan (RGBS / YPbPr) off = Picture is displayed at the maximum size that will fit on the screen without losing video information. Picture may have black bars top and bottom or left and right. on = Over scans the screen by 5%. Select using or buttons.

8

DVI Digital Picture Menu

Sharpness Press or to adjust the sharpness (focus) of the displayed image. Note: Cannot be adjusted when the display is operating at native resolution. Scaling Fill = Expands the video image to fill the entire screen. The aspect ratio may not be accurately displayed. Aspect = Expands the video image until its largest dimension fills the screen. Image may be displayed with black bars on the top and bottom or the left and right. 1:1 = Displays the video data in its native size and aspect ratio. Image may be displayed with black bars on the top and bottom and on the left and right. Select using or buttons.

BIOS 58B0213 only: HD-SDI Picture Menu

Sharpness Press or

to adjust the sharpness (focus) of the displayed image.

Overscan off = Picture is displayed at the maximum size that will fit on the screen without losing video information. on = Stretches picture horizontally and vertically to fill the screen, but does not change its aspect ratio. Some video information may be lost. Picture may have black bars top and bottom or left and right. Select using or buttons.

9

Color Menus

VGA and DVI Digital

SOG

SD SDI, RGBS, YPbPr, S-Video and Composite

HD SDI

Gamma (VGA, DVI-digital and SOG) Press or to select a preset Gamma, Video or PACS Notes: 1. Video is a color corrected Look Up Table (LUT) available with DVI, SOG and VGA. 2. Picture Archive Communications System (PACS) is a DICOM-like LUT available with DVI, SOG and VGA. 3. Video is not available when the input is SOG. Saturation (SDI, RGBS, YPbPr, S-Video and Composite) Press or to set the saturation (color intensity) of the image. Not available with HD SDI (BIOS 58B0213). Red, Green, Blue (All except SOG) Press the or button to increase or decrease the intensity of the selected color. Hue (SDI, RGBS, YPbPr, S-Video and Composite) Press or to set the hue (color tint) of the image. Not available with HD SDI (BIOS 58B0213). 10

Setup Menu

Menu Position Places the menu in 1 of 9 predefined screen positions. Press the positions.

or

button to select any of the 9 screen

Language Selects 1 of 7 languages: English, Deutsch, Francais, Italiano, Scandinavia, Espanol or Dutch. Press the button to select any of the 7 languages.

or

DPMS Enable Display Power Management System. When DPMS is enabled (on), and no input signal is present, an “Entering Power-Save Mode” message is displayed for 10 - 15 seconds, after which the display shuts down. This prolongs the life of the backlight tubes in the display. The display turns on when the input signal is restored. Press the button to enable DPMS, press the button to disable DPMS. Auto Source Select on = Searches through all possible input sources until an active video source is found. off = Video input is manually selected. Press the or button to disable or enable Auto Source Select. Menu Lock Disables access to menu system. This prevents inadvertent changes to the display’s settings. To enable Menu Lock, press the button. MENU LOCKED is displayed when the button is pressed. To unlock, simultaneously press and hold the MENU and SCROLL buttons until MENU UNLOCKED is displayed. BIOS 58B0180, 58B0190 and 58B0213 Operating Hours: Backlight hours of operation. BIOS: Version of the display’s BIOS firmware.

11

Defaults Menu

BIOS 58B0180, 58B0190 and 58B0213 Factory Defaults Displays Restoring Factory Defaults message and returns all settings to their factory preset values. Press the SCROLL button to highlight Factory Defaults, then press the button. User Defaults Allows up to five customized user settings to be saved. Setting User Defaults 1. Set the Picture, Color and Setup parameters to the user’s preferences. 2. Select the Defaults tab. 3. Use the SCROLL button to select an available User Defaults. ***EMPTY*** appears in available User Defaults. 4. Press the to save the user’s settings. The ***EMPTY*** message will be removed, see User Defaults 1 in the above OSM illustration. 5. Repeat steps 1 thru 4 for up to 5 users. Restoring User Defaults 1. Select the User Defaults to be restored, then press the

button .

Clearing User Defaults 1. Select the User Defaults to be cleared, then press the Brightness / Contrast button . Note: The prompt at the bottom of the Defaults menu appears only when one of the User Defaults is selected.

Defaults Menu

BIOS 58B0172 and 58B0178 Factory Defaults Displays Restoring Factory Defaults message and returns all settings to their factory preset values. Press the SCROLL button to highlight Factory Defaults, then press the button. Operating Hours: Backlight hours of operation. BIOS: Version of the display’s BIOS firmware.

12

Troubleshooting Section Image Size is Very Large for the Screen If the computer data does not appear to be the correct format, then SmartSync™ must be run. To run SmartSync™, press the Menu button. Select the Setup menu. Press SCROLL to highlight SmartSync™ , then press the button. SmartSync™ will run and size the image properly. Ghosting in Characters Ghosting in characters is usually attributed to reflections in the video cable or source. Use a high quality coaxial cable and, if possible, lower the vertical refresh rate. Lower scan rates can help eliminate reflections. Unlike a CRT a flat-panel will not flicker at lower refresh rates (60 Hz is optimal) and data update will be the same at all refresh rates.

6

Text is Too Small Since the monitor accepts and displays computer data with a higher resolution than the display’s native resolution, this may produce small text. In the Menu check the Display Mode tab. Verify that the computer data resolution does not exceed the Native Resolution specification shown on page 17. Character Jitter If text characters seem to be “shaky” or bold, then Sharpness, Frequency and / or Phase may require adjusting. See: Setting Frequency, Phase and Sharpness below. Character Noise and Vertical Distortion The Frequency adjustment expands or contracts the horizontal size of the displayed image. The displayed image may be too wide or too narrow and vertical banding and pixel jitter may appear in grays and light colors. Adjust the Frequency until the image just fits the screen. Horizontal position adjustment can be used to verify that Frequency is set correctly. Line up the image on the left edge of the screen and then shift by one “click” to the right. The image should have one column off the screen on the right side if the Frequency is set correctly. Black Screen Power the display Off and On. If the NDS logo appears then the display is working properly. Check if the power management feature (DPMS) is enabled. An “Out of Range” message appears in the upper left hand corner when an input source is out of the display’s resolution range. A “Searching” message appears in the lower right hand corner when the video source is not present. Setting Frequency, Phase and Sharpness Windows Users: Open a WordPad document and set the font to Arial 8. Press the enter key to move the cursor to the middle of the page. Hold the shift and + keys down to create a line of +s. If the + signs appear in groups of light or dark, then the Frequency is not correct. Press the MENU button to open the OSM, then SCROLL to the Frequency parameter. Press the or buttons to increase or decrease Frequency. There will be a point were all the + signs snap into focus and are the same intensity. Phase and Sharpness are subtle adjustments and are best set using a display calibration program.

13

Drawing and Dimensions

Display Stand is an optional accessory. Order Part Number: 26B0063

7

14

Data Connectors and Pin Outs DVI-D* Digital Input

RGBS / YPbPr 1 RED

6 GND RED

11 N. C.

2 GREEN

7 GND GREEN

12 N. C.

3 BLUE

8 GND BLUE

13 C. Sync / H. Sync.

4 N. C.

9 N. C.

5 GND TEST

10 GND

8

PIN#

SIGNAL

PIN#

SIGNAL

1

T.M.D.S. DATA 2-

16

HOT PLUG DETECT

14 V. Sync.

2

T.M.D.S. DATA 2+

17

T.M.D.S. DATA 0-

15 N. C.

3

T.M.D.S. DATA 2/4 SHIELD

18

T.M.D.S. DATA 0+

4

T.M.D.S. DATA 4-

19

T.M.D.S. DATA 0/5 SHIELD

5

T.M.D.S. DATA 4+

20

T.M.D.S. DATA 5-

6

DDC CLOCK

21

T.M.D.S. DATA 5+

7

DDC DATA

22

T.M.D.S. CLOCK SHIELD

8

N/C

23

T.M.D.S. CLOCK+

9

T.M.D.S. DATA 1-

24

T.M.D.S. CLOCK-

10

T.M.D.S. DATA 1+

11

T.M.D.S. DATA 1/3 SHIELD

C1

N/C

12

T.M.D.S. DATA 3-

C2

N/C

13

T.M.D.S. DATA 3+

C3

N/C

VGA 1 RED

6 GND RED

11 ID0

2 GREEN

7 GND GREEN

12 ID1

3 BLUE

8 GND BLUE

13 HORIZ SYNC

14

+5V POWER

C4

N/C

4 ID2

9 N. C.

14 VERT SYNC.

15

GND

C5

N/C

5 GND

10 SYNC GND

15 ID3

* Compliant with DVI 1.0

Serial and / or Touch Screen Control

S-Video

Name

Description

1

NC

2

RXD Touch Screen Data Receive

3

TXD Flash Upgrade & Touch Screen Transmit

4

NC

5

GND Ground

6

NC

7

NC

Pin

Name

1

GND

Ground (Y)

8

NC

2

GND

Ground (C)

9

RXD Flash Upgrade Receive Data

3

Y

Intensity (Luminance)

4

C

Color (Chrominance)

Note: The following cables are available from NDS. 1. Flash Upgrade Cable order part number: 35Z0009

15

Description

Pin

GPIO Connectors and Pin Outs General Purpose Input and Output (GPIO) Source Toggle The Source Toggle is activated by a momentary contact closure to the ground pin. GPIO Source Selection setup and usage details are on page 6. Recording Indicator The Recording Indicator is displayed while a contact closure to the ground pin is present, the indicator is removed when the contacts are opened. The Recording Indicator, shown below, is displayed in the monitor’s top left corner. BIOS 58B0172 and BIOS 58B0178

BIOS 58B0180, 58B0190 and 58B0213

GPIO Mating connector: CUI Inc. MD-60

GPIO Mating connector: RJH 4 pin Telephone Handset Connector

Pin Name

Description

1 GND Common Ground. Pin Name

Description

2 GND Common Ground.

1 RFU .Reserved for Future Use

3 N/C Reserved for future use.

2

S.T. Source Toggle.

4 S.T. Source Toggle.

3

R.I. Recording Indicator.

5 R.I.

4 GND Common Ground

Recording Indicator.

6 N/C Reserved for future use.

Power Connector and Pin Out 24 volt connector X Z

Pin

1

2

3

+ 24 VDC

GND

Shield

Y

24 Volt Extension Cables Note: Use of an extension cable may invalidate the unit’s UL Classification. Use only copper wire for power wiring. Power extension cable shall be constructed in accordance with applicable hospital and electrical codes. The table below shows the maximum cable length for a given wire gauge. Cable should be constructed of SJT, SJTO, SJO, ST, SO, STO or equivalent flexible cord per US National Difference Clause 59.1DV. Users outside of the U.S. should adhere to the applicable electrical codes for their country. The cable requires one each of the following connectors: Switchcraft SL403F (female) and SL413M (male). See illustration below. AWG

Maximum Length

14

250 ft / 76 m

16

150 ft / 45 m

18

100 ft / 30 m 16