Rocket Craft Pump User Manual Rev 07 Jan 2009

Page 2

USERS MANUAL – ROCKET® CRAFT™ SUCTION PUMPS – ALL MODELS

Page 2

1. ROCKET® CRAFT™ SUCTION PUMPS

1.1. General Description:

The Rocket® Craft™ Suction Pumps have been developed to provide a smooth, low volume

vacuum at a pre-determined negative pressure. Vacuum is activated by a foot operated switch

controlled by the surgeon performing oocyte collection.

The range of vacuum is variable from 0-400mm Hg and adjustable over this range by a pre-set

control. Vacuum is provided by a quiet diaphragm pump, working from a mains voltage supply

and manufactured to BS 5724 Class 1 and CE safety regulations.

The Rocket® Craft™ is supplied with both a reusable water trap set as standard designed to

help prevent aspirated fluids being drawn into the vacuum power unit. The trap also acts as a

reservoir to provide an even vacuum pressure during procedures. A single patient use,

disposable water trap set is also available.

The foot control has an air-operated solenoid, switching the main pump unit. No electrical

connections are made to the sealed foot operated control.

A suitable collection test tube for use with oocyte needle sets is B.D. Falcon test tube No.

2001F, 17 x 100mm.

1.2. References:

Craft I, McLeod F. Edmonds K, ‘Human embryo transfer technique’. Lancet 1961 ii 1104-5

Craft I, Diahanbakch O. McLeod F et al ‘Human pregnancy following oocyte and sperm transfer

to the uterus.’ Lancet 1992 i 1031-3

Craft I, (1984) ‘Clinical Methodology’ British Journal of Hospital Medicine 90-102

ZDOCK105

Rev. 07

15/01/09

Copyright© ROCKET MEDICAL PLC 2001- 2009

Page 3

USERS MANUAL – ROCKET® CRAFT™ SUCTION PUMPS – ALL MODELS

Page 3

1.3. Warranty

Rocket® Craft™ 220V Suction Pumps are sold by Rocket Medical plc under the warranties set

forth in the following paragraphs. Such warranties are extended only with respect to the

purchase of the Products directly from Rocket Medical plc as new merchandise and are

extended to the first Buyer thereof, other than for resale.

For a period of twelve (12) months from the date of shipment the Products are warranted to be

free from functional defects in materials and workmanship and to conform to the description of

the Products contained in the operating manual and accompanying labels, provided the same is

properly operated under conditions of normal use, that annual maintenance and service is

performed at an authorised Rocket Medical plc service facility

Removal of any QC seal voids the warranty.

The foregoing warranties shall not apply if the Products have been repaired other than by

Rocket Medical plc or other than in accordance with written instructions provided by Rocket

Medical plc , or altered by anyone other than Rocket Medical plc, or if the Products have been

subject to misuse, negligence, or accident.

Rocket Medical plc 's sole and exclusive obligation and Buyer's sole and exclusive remedy

under the above warranties is limited to repairing or replacing, free of charge, at Rocket

Medical plc 's option, Products, which are telephonically reported to Rocket Medical plc and

which, if so advised by Rocket Medical plc, is thereafter returned with a statement of the

observed deficiency, not later than seven (7) days after the expiration date of the warranty, to

Rocket Medical plc during normal business hours, transporting charges prepaid and which,

upon Rocket Medical plc's examination, is not found to conform with the above warranties.

Rocket Medical plc shall not be otherwise liable for any damages including but not limited to

incidental damages, consequential damages or special damages.

There are no express or implied warranties which extend beyond the warranties herein above

set forth. Rocket Medical plc makes no warranty of merchantability or fitness for a particular

purpose with respect to the Products or parts thereof.

1.4. Service and Repairs:

Craft™ Pumps normally require little routine maintenance, however they must be serviced and

calibrated annually at an Rocket Medical plc service facility.

Please contact any of our Customer Services Departments for details of your nearest service

centre

ZDOCK105

Rev. 07

15/01/09

Copyright© ROCKET MEDICAL PLC 2001- 2009

Page 4

USERS MANUAL – ROCKET® CRAFT™ SUCTION PUMPS – ALL MODELS

Page 4

2. OPERATING INSTRUCTIONS ROCKET® CRAFT™

VACUUM UNIT R29.654 & R29.655

9

Connect main lead to electrical supply 230/240 volt 50 Hz

(R29.655) or 110/120 volt 60 Hz. (R29.654)

9

The reusable water trap set should be packed and sterilised by

autoclaving at 135°C @ 3 bar for 3 mins. prior to each use.

9

Rocket Medical plc recommend the use of Rocket® Craft™

Single Use Water Trap sets which are available from your local

agent or Customer Services.

9

Using aseptic technique, unpack the water trap and insert the

glass water trap bottle into the clip at the left hand side of the

casing.

9

Connect the short tube to the port marked SUCTION and secure

with a light push fit.

9

Pass the longer patient connection tube into the operative field.

9

Connect foot switch tube to connector on front panel.

9

Activate vacuum by depressing foot switch. The pump will stop

when the foot is lifted from the pad.

9

Set the required vacuum required by occluding the vacuum line

distal (patient side) to the water trap and adjusting the control to

the desired level as shown by the needle on the gauge

Craft™ Single Use Water Trap Set

9

During the aspiration of the fluid the control knob may be adjusted to the

precise vacuum require under load, approximately 100-200mm Hg.

9

NOTE: Thinner gauge needles (17G) and those with longer tube sets, 7090cm may require vacuums in the region of 150-200mmHg to achieve

satisfactory flow rates.

9

The unit is then ready for use.

9

If vacuum lines become blocked due to debris or viscous fluids, a

temporary high vacuum can be obtained to unblock the needle and tubing

by occluding the finger bleed hole on the front panel, marked “OCCLUDE

FOR MAXIMUM VACUUM”. High vacuum should NOT be used to aspirate oocytes.

9

Placing a finger on the red disc for a few seconds will clear the tubing lines at 300-400mm Hg

temporary high vacuum.

9

On completion depress front panel

switch at “O” to switch the unit off.

Craft™ Suction Pump with single foot control, shown with re-us

ZDOCK105

Rev. 07

15/01/09

Copyright© ROCKET MEDICAL PLC 2001- 2009

Page 5

USERS MANUAL – ROCKET® CRAFT™ SUCTION PUMPS – ALL MODELS

Page 5

3. OPERATING INSTRUCTIONS ROCKET® CRAFT™

VACUUM UNIT R29.660 & R29.661

9

9

Connect main lead to electrical supply 230/240 volt 50 Hz

(R29.660) or 110/120 volt 60 Hz. (R29.661)

Connect the dual foot switch tubes to the push connectors on

front panel.

9

The reusable water trap set should be packed and sterilised by

autoclaving at 135°C @ 3 bar for 3 mins prior to each use.

9

Rocket Medical plc recommend the use of Rocket® Craft™

Single Use Water Trap sets which are available from your local

agent or Customer Services.

9

Using aseptic technique, unpack the water trap and insert the

glass water trap bottle into the clip at the left hand side of the

casing. Reusable water trap sets are available, contact your local

agent or Customer Services.

9

Connect the short tube to the port marked SUCTION and secure

with a light push fit.

9

Pass the longer patient connection tube into the operative field.

9

9

Connect foot switch tube to connector on front panel.

Activate vacuum by depressing LOW VACUUM (Larger) foot

switch. The pump will stop when the foot is lifted from the pad.

9

Set the required vacuum required by occluding the vacuum line distal

(patient side) to the water trap and adjusting the control to the desired

level as shown by the needle on the gauge

9

During the aspiration of the fluid, the control knob may be adjusted to

the precise vacuum required under load, approximately 100-200mmHg.

9

NOTE: Thinner gauge needles (17G) and those with longer tube sets,

70-90cm may require vacuums in the region of 150-200mmHg to

achieve satisfactory flow rates.

9

The unit is now ready for use.

9

If vacuum lines become blocked due to debris or viscous fluids, a temporary high vacuum can be

obtained to unblock the needle and tubing by depressing the smaller HIGH Vacuum foot switch this

provides a temporary high vacuum up to 440mmHg.

9

High vacuum should NOT be used to

aspirate oocytes.

9

On completion depress font panel

switch at “O” to switch the unit off.

®

Rocket Craft™ Single Use Water Trap Set

Craft™ DuoVac with twin foot control and reusab

ZDOCK105

Rev. 07

15/01/09

Copyright© ROCKET MEDICAL PLC 2001- 2009

Page 6

USERS MANUAL – ROCKET® CRAFT™ SUCTION PUMPS – ALL MODELS

Page 6

Rocket® Single Use Water Trap Set

for use with all Rocket® Craft™

Suction Pumps

The Rocket® Water Trap Set for use with Rocket® Craft™

Suction Pumps offers a simple, cost effective solution to

contamination risks and reuse problems.

• COMPLETE SET: Provides the complete bottle and tubing set

in single, sterile pack for one time patient use.

• GLASS TRAP BOTTLE: To maintain clear view in the event of

potential pump contamination with aspirate. Designed to

withstand >450mmHg vacuum.

• REMOVES CONTAMINATION RISK from irregular or

uncontrolled decontamination of reusable bottle, bung and

angle tube set.

• PATIENT TUBE SET: 2m patient tube set with integral luer

lock connector to ensure secure, reliable connection to the

aspiration needle set.

• SUITABLE FOR USE: Compatible with all versions of Craft™

Suction and Duo Vac.

• Also compatible with the genX and Pioneer Pro Pumps.

Ordering Information

Rocket® Water Trap Set suitable for all

Rocket® Craft™ Suction Pumps

Sterile

each

R57.685

Packed individually, 10 per carton

ZDOCK105

Rev. 07

15/01/09

Copyright© ROCKET MEDICAL PLC 2001- 2009

Page 7

USERS MANUAL – ROCKET® CRAFT™ SUCTION PUMPS – ALL MODELS

Page 7

4. SPARE PARTS: CRAFT SUCTION PUMPS:

Item

1.

3.

10.

11.

12.

14.

15.

18.

19.

20.

21/22

22.

23.

25.

28

104.

Part No.

R29.655

R29.654

B14-011

B02-009

B02-140

F06-006

R06-027

C12-030

F04-027

F04-023

E05-000

N05-016

K01-001

O04-000

G03-005

C01-035

I08-004

S10-027

C01-034

B05-005

Description

CRAFT SUCTION PUMP, 240V.

CRAFT SUCTION PUMP, 110V.

Box, lower half

Bottle Bracket

Bottle Bracket assembly (bracket & white plastic coated clip)

Front Panel Fin

Rear Panel 240v

Chassis bare

Filter assembly (Silencer)

Filter housing assembly

Filter Element (part of item 15)

Needle Valve assembly

Knob Pointer

Vacuum Control Orifice assembly

Vacuum Gauge 0-600mmHG and connector assembly (items 21 & 22)

Connector

IEC Connector

Switch 240v

Flanged Connector

Footswitch

(Cat.No. R29.656)

59.

11.

19.

44

13.

34.

30.

42.

56.

55.

48.

58.

51.

50.

45.

52.

53

104.

22.

-

R29.660

R29.661

B14-009

B14-011

C12-044

F06-022

B02-009

S10-007

S18-004

I08-004

S10-001

N05-014

K01-001

G03-004

B20-010

N06-002

N06-003

C01-034

C01-179

C01-178

B05-004

F04-004

C01-176

C01-177

CRAFT DUO-VAC SUCTION PUMP 240V.

CRAFT DUO-VAC SUCTION PUMP 110V.

Case Upper Half

Case Lower Half

Chassis

Front Panel

Bottle Bracket

Pressure Switch

Solenoid Valve

IEC Connector

Switch/Indicator

Stop Pin/Nut (Part of N05-016 Needle Valve Assembly)

Knob

Vacuum Gauge 0-600mmHG

Ventilator blanks

Neon Indicator Green

Neon Indicator Red

Flanged connector

Plastic Connector MALE (on front of Pump under standard vacuum green indicator)

Plastic Connector FEMALE (on front of Pump under high red vacuum indicator)

Footswitch, Dual Vacuum

(Cat.No.R29.662)

Filter Assembly (silencer)

Set of 2 Plastic connectors for Footswitch, high vacuum

Green Connector (Female) for lead on Dual Footswitch

Red Connector (male) for lead on Dual Footswitch

ZDOCK105

Rev. 07

15/01/09

Copyright© ROCKET MEDICAL PLC 2001- 2009

Page 8

USERS MANUAL – ROCKET® CRAFT™ SUCTION PUMPS – ALL MODELS

Page 8

4.1.MOTOR SPARES & ACCESSORIES

Item

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

Part No.

SO1-214

WO1-000

SO1-138

HO1-001

VO1-002

VO2-001

SO1-203

DO2-001

GO1-001

DO1-053

CO2-031

BO2-035

SO1-104

WO1-051

SO1-018

C03-084

MO1-311

15

MO1-312

-

S02-012

ZDOCK105

Rev. 07

Description

Screw 4BA x 3/4" pan pozi b'zinc

Washer for the above (flat) 6BA b'zinc

Head Screw (centre) no. 4 x 1/4" pan pozi

Head 800111

Valve diaphragm 800109B EPDM

Valve plate 800110

Screw 6BA X 5/16" csk S/S

Diaphragm plate upper 700172

Gasket 690260 Grey Poly

Pump Diaphragm 700190C EPDM

Crankcase 770137

Bracket 820170 blk. anodis

Screw no 4 x 3/16" pan pozi 'B' b'zinc

Washers S/P int. M4 bzn

Screws M4 x 10 pan pozi bzn

Complete Conrod Assembly, including top diaphragm plate

Motor 770139 220/240v

(includes motor, crank case and valves)

Motor 730190 110/120v 50 Hz.

(includes motor, crank case and valves)

Service Kits (EPDM) includes items 3 and 8 plus a washer

15/01/09

Copyright© ROCKET MEDICAL PLC 2001- 2009

Qty.

4

4

1

1

1

1

1

1

1

1

1

1

4

2

2

1

1

1

1