3M
Steri-Vac GSX Series Sterilizer / Aerator Operators Manual
92 Pages
Preview
Page 1
3M™ Steri-Vac™ Sterilizer/Aerator GSX Series
Operator’s Manual
4577604 Description: 3M™ Steri-Vac™ Sterilizer / Aerator GSX Series Op. Manual Manual Base File Name: PA: 34872129035_A.indd GA: Software: InDesign CC 2014 SGS Contact: Email: Printer: Printer Location: Supplier:
PROCESS BLACK
PROCESS CYAN
PROCESS MAGENTA
6
Item Spec#: 34-8721-2903-5.A Supersedes#: Structure#: Cat/Product#: Reference: GSX Series
05.16.17 PU from SGS#4010865 and make changes per marked up PDF 05.30.17 Alts per Proof Report 06.22.17 Update 34# & final release. 07.21.17 Change 34 Number 07.26.17 Replace UPC. 07.31.17 Final Release
Requester: Linda Thompson Die # / Doc. Size: 8.5" x 11"
PROCESS YELLOW
PDF Scaled to 100%
kmh kmh TN TF DJ kmh
Table of Contents Explanation of Symbols... 2 11. 3M™ Cycle Programmer... 31 Product and package labels and pictograms ...2
11.1. 3M™ Cycle Programmer Overview ...31
Operator Manual...3
11.2. 3M™ Cycle Programmer Hardware and Software Requirements...31
Content Disclaimers ... 3
13.3.1. Cycle Stages and Descriptions ...66 13.3.2. Cycle Reports...67
13.4. Cartridge Dispose Cycle for 3M™ Steri-Gas™ EO Gas Cartridges ...70
11.2.1. Hardware Requirements ...31
13.5. Ethernet Connection ...70
1. Description ... 4
11.2.2. Software Requirements ...32
13.5.1. Network Connections ...70
2. Intended Use... 5
11.3. Installing the 3M™ Cycle Programmer...32
13.5.2. IP Addresses ...70
3. Safety ... 6
11.4. Creating a Cycle in the 3M™ Cycle Programmer ...34
4. Dangers and First Aid... 7
11.5. Defining Set Points for Cycle Stages and Parameters .37
4.1. Dangers ...7
11.5.1. Preheat Stage ...37 11.5.2. Air Removal Stage ...37
4.2. First Aid...8
11.5.3. Chamber Test Stage ...37
5. Warnings ... 9
11.5.4. Conditioning Stage ...38
6. Cautions ... 10
11.5.5. EO Injection Stage ...39 11.5.6. EO Exposure Stage ...40
7. Specifications... 11
11.5.7. EO Removal Stage...40
7.1. 3M™ Steri-Vac™ Sterilizer/Aerator GSX Series Structural Specifications ...11
11.5.8. Flushing Stage ...41
7.2. Sound Power Levels Specifications...11
11.5.10. Save a Custom Cycle...42
7.3. Power Specifications ...11
11.5.9. Aeration Stage ...42 11.5.11. Standby Stage...43 11.5.12. Estimated Total Cycle Time ...43
7.4. Air Supply Specifications ...12
8. Compliance and Reference Standards ... 12 8.1. Device Safety Compliance...12 8.2. Electromagnetic Compatibility (EMC) Compliance...12
9. Installation and Set Up... 13 9.1. Environmental Operating Conditions ...13 9.2. Room and Installation Requirements...14 9.3. Set up and Connections ...15
10. Using the Touch Screen... 18 10.1. Main Screen ...18 10.2. Menu ...18
11.6. Importing Custom Cycles to the 3M™ Steri-Vac™ Sterilizer/Aerator GSX Series ...44 11.7. Running Custom Cycles on the 3M™ Steri-Vac™ Sterilizer/Aerator GSX Series ...47
13.5.3. Software Security ...71 13.5.4. Software Updates ...71 13.5.5. Firmware Updates ...71
13.6. Distilled Water Reservoir ...72 13.7. Printer Overview...72 13.8. Unloading the 3M™ Steri-Vac™ Sterilizer/ Aerator GSX Series ...72 13.8.1. Unloading the 3M™ Steri-Vac™ Sterilizer/ Aerator GSX Series – Cycle Complete ...73
13.9. Accessing the Chamber – Aeration Not Complete...74 13.10. Empty 3M™ Steri-Gas™ Ethylene Oxide (EO) Gas Cartridges...75 13.11. Aeration of a Biological Indicator Process Challenge Device (BI PCD)...75 13.12. Sterilization Cycle Cancellations...75 13.12.1. Manual Cycle Cancellation ...75 13.12.2. Automatic Cycle Cancellation ...75
13.13. Power Outages...75
11.8. Managing Custom Cycles on the 3M™ Steri-Vac™ 14. Process Monitoring and Load Release ... 76 Sterilizer/Aerator GSX Series ...48 14.1. Physical Parameters and Requirements...76 11.9. Replacing Cycles on the 3M™ Steri-Vac™ Sterilizer/ 14.2. Biological Indicators and Process Challenge Devices..78 Aerator GSX Series With the Same Name ...49 11.10. Removing Custom Cycles from the 15. Routine Maintenance ... 79 3M™ Steri-Vac™ Sterilizer/Aerator GSX Series ...50 15.1. Daily Cleaning ...79 11.11. Cycle Reports ...51 15.2. Air Supply Line Filters ...79 11.11.1. Custom Cycle Set Points ...51 11.11.2. Export Cycle Data ...52
15.3. Preventative Maintenance ...80
16. Cautions, Error Messages, and Troubleshooting ... 81 10.3. Reports ...19 12. Medical Device Packaging and Loading ... 53 16.1. Caution Messages...81 10.3.1. Cycle Reports...19 12.1. Preparing Medical Devices for Sterilization ...53 10.3.2. Ethylene Oxide Usage Reports...20 10.3.3. Site Setup Report ...21 10.3.4. Printer Form Feed...22
12.1.1. Preparing Endoscopes for EO Sterilization...53
16.2. Error Messages ...82
12.2. Packaging Medical Devices...54
16.3. Error Levels and Corrective Actions...83
12.2.1. Packaging Endoscopes for EO Sterilization...54
17. Repair and Replacement ... 85
10.4. Cycle Categories...22
12.2.2. Recommended Packaging ...54
10.4.1. Operator Cycles...22
12.2.3. Non-compatible Packaging ...54
18. Preventative Maintenance ... 85
10.4.2. Supervisor Cycles ...23
12.2.4. Package Medical Devices ...55
19. Ordering Accessories and Supplies... 86
10.5. Setup Menu ...24 10.5.1. Site Setup ...24
12.3. Loading the 3M™ Steri-Vac™ Sterilizer/ 20. 3M™ Cycle Programmer Support and Aerator GSX Series ...55 Software Updates... 87
10.5.2. User Setup ...28
12.3.1. Loading Recommendations...55
10.6. Status ...30
12.3.2. Loading Medical Devices and Instruments ...55
10.6.1. Control...30
13. Operating Instructions ... 56
10.6.2. Info ...30
13.1. Starting a Cycle ...56
10.6.3. Log ...30
13.2. Display Screen Indications ...65 13.3. Overview of GSX Series Ethylene Oxide (EO) Sterilization Cycle ...66
Contact Information ...87 U.S. Ordering Information ...87 Orders for Supplies (e.g. 3M™ Steri-Gas™ EO Gas Cartridges, 3M™ Attest™ Biological Indicators, 3M™ Printer Paper)* ...87
3M™ Steri-Vac™ Sterilizer / Aerator GSX Series – Operator’s Manual
Explanation of Symbols: product and package labels and pictograms Refer to the package and product labels to see which symbols apply to specific products. Attention - Refer to the Operator Manual for additional information. Warning - Indicates a hazardous situation, which, if not avoided, could result in death or serious injury. Waste Electrical and Electronic Equipment (WEEE) and EU Battery Directive. This symbol indicates that both the device and lithium ion battery contained therein need to be disposed of properly. UL Classified to U.S. and Canadian Safety Standards. Mark of Conformity to European Directives. Compliant to all applicable ACMA regulatory arrangements (RCM). Serial number - This symbol is accompanied by the serial number relevant to the device bearing the symbol. Catalog - This symbol is accompanied by the catalog number relevant to the device bearing the symbol. Authorized representative for the European Community – This symbol is accompanied by the name and the address of the authorized representative in the European Community. Manufacturer – This symbol is accompanied by the name and address of the manufacturer. Date of Manufacture - This symbol is accompanied by the date of manufacture. Do not top load. Lift with forklift. Fragile. Keep dry. This way up. Unique Device Identification (UDI) barcode (located on the sterilizer serial plate). Pictograms are documented according to the European Union (EU) Classification Labeling and Packaging (CLP) Regulation and the Globally Harmonized System (GHS) of Classification and Labeling of Chemicals. Flame - Flammable Gas: Category 1 Skull and Cross Bones - Acute Toxicity (inhalation): Category 3 Health Hazards
2
Classification Labeling and Packaging (CLP) Regulation Serious Eye Damage/Eye Irritation, Category 2 - Eye Irrit. 2; H319 Skin Corrosion/Irritation, Category 2 - Skin Irrit. 2; H315 Carcinogenicity, Category 1B - Carc. 1B; H350 Germ Cell Mutagenicity, Category 1B - Muta. 1B; H340 Specific Target Organ Toxicity-Single Exposure, Category 3 - STOT SE 3; H335
Globally Harmonized System (GHS) of Classification and Labeling of Chemicals Specific Target Organ Toxicity (single exposure): Category 1 Specific Target Organ Toxicity (repeated exposure): Category 1 Specific Target Organ Toxicity (central nervous system): Category 3 Carcinogenicity: Category 1A Reproductive Toxicity: Category 2 Germ Cell Mutagenicity: Category 1B Eye Irritation: Category 2A Skin Irritation: Category 2
Additional pictograms for Globally Harmonized System (GHS) of Classification and Labeling of Chemicals Gas Cylinder - Gas Under Pressure: Liquefied Gas The gas cylinder pictogram applies to Globally Harmonized System (GHS) of Classification and Labeling of Chemicals. The gas cylinder is not applicable where the European Union (EU) Classification Labeling and Packaging (CLP) Regulation applies. Exclamation Mark - Irritant, Acute toxicity (harmful) Respiratory Tract, Irritation The exclamation mark in red border pictogram applies to Globally Harmonized System (GHS) of Classification and Labeling of Chemicals. The exclamation mark in red border is not applicable where the European Union (EU) Classification Labeling and Packaging (CLP) Regulation applies.
Explanation of Symbols: Operator Manual Danger: Indicates a hazardous situation which, if not avoided, will result in death or serious injury. Warning: Indicates a hazardous situation, which, if not avoided, could result in death or serious injury. Caution: Indicates a hazardous situation, which, if not avoided, could result in minor or moderate injury. NOTICE: Indicates a hazardous situation which, if not avoided, may result in property damage.
Content Disclaimers Pictorial Disclaimer Sample printouts, graphics, displays and screens are for information and illustration purposes only and shall not be used for clinical or maintenance evaluations. Data shown in sample printouts and screens do not reflect actual names or test results.
Hardware Disclaimer The 3M™ Steri-Vac™ Sterilizer/Aerator GSX Series hardware and software are subject to change. The system images, screen images, hardware components, and hardware specifications included in the manual may not match the system as installed. In the event that hardware or software changes are made, 3M will verify their compatibility with the functionality described in this document.
Serial Number For easy identification, each 3M™ Steri-Vac™ Sterilizer/Aerator GSX Series has a unique serial number printed on the serial label (e.g. EA343434) found on the right side of the unit and displayed on the printout for each cycle completed. Record your serial number in this manual for future reference: ________________________________. 3
3M™ Steri-Vac™ Sterilizer / Aerator GSX Series – Operator’s Manual
1. Description The 3M™ Steri-Vac™ Sterilizer/Aerator GSX Series is for use in industrial sterilization, research, lab, veterinary surgical and other appropriate settings. When installed, operated and maintained as described in this Operator Manual, the equipment is safe and effective. All Operators must be fully trained in the recommended operation of this device. The GSX Series sterilizer utilizes an embedded software controlled system to ensure that specified sterilization conditions are met and to minimize the possibility of operator exposure to ethylene oxide (EO) gas. Use of this equipment in a manner not specified by 3M has not been evaluated and may lead to an unsafe condition. The GSX Series sterilizer, with the 3M™ Cycle Programmer, provides the user with options to develop optimized and unique EO processes specialized and tailored to the user’s specific product requirements (e.g. drug-device combination products). The 3M Cycle Programmer allows programming of 28 different parameters in eight of the nine active stages of the EO sterilization process and operates on a personal computer (PC) supplied by the user. Custom cycles are created with the 3M Cycle Programmer and imported to the GSX Series sterilizer using a USB drive. Alternatively, the user can choose to operate the GSX Series sterilizer by using the two 3M validated preprogrammed sterilizer cycles, GSX 38C and GSX 55C. The user can also choose to develop a combination cycle containing preprogrammed and customized cycle parameters to meet the configuration of their product design. The GSX Series sterilizer can automatically aerate the processed load in the sterilization chamber after sterilization. If preferred, the load can be transferred to the 3M™ Steri-Vac™ XL Aerator, aeration cabinet, or aeration room for aeration thereby releasing the sterilizer for the next load. The 3M Cycle Programmer operates on an independent PC computer supplied by the user. Custom cycles are created within the 3M Cycle Programmer and are imported to the GSX Series sterilizer from a USB drive. The 3M Cycle Programmer will not function directly on the GSX Series sterilizer. The GSX Series sterilizer contains two preprogrammed cycles, GSX 38C and GSX 55C, that can be selected and used without modification by the end user. The critical sterilization process set points (e.g. temperature, humidity level, sterilant concentration, exposure time) for these preprogrammed cycles are identical to the critical process set points in the 3M™ Steri-Vac™ Sterilizer/Aerator GS Series, Models GS5 and GS8, and have been validated per US FDA Guidance on Premarket Notification [510(k)] Submissions for Sterilizers Intended for Use in Health Care Facilities reference 510(k) number K142034. These critical sterilization process parameters and set points for the preprogrammed cycles are documented in Table 1. The end user is responsible for determining if these preprogrammed cycles are suitable for their specific application, with regards to safety and efficacy, and for any verification or validation documentation required for their application. Preprogrammed Cycle
Process Temperature (°C)
Process Relative Humidity %RH
EO Gas Concentration* (mg/L)
EO Exposure Time (hour + min)
Aeration Temp (°C)
4.5 hr ± 5.4 min
38 ± 3
Aeration Time (hours)
GS5X w/ 4-100 = 735 GS5X w/ 4-134 = 934 GSX 38C
38 ± 3
40 - 80
GS8X w/ 4-100 = 446 GS8X w/ 4-134 = 567 GS8X w/ 8-170 = 759
Programmable by the Operator
GS5X w/ 4-100 = 735 GS5X w/ 4-134 = 934 GSX 55C
55 ± 3
40 - 80
GS8X w/ 4-100 = 446
1.0 hr ± 1.2 min
55 ± 3
GS8X w/ 4-134 = 567 GS8X w/ 8-170 = 759 * EO Gas Concentration is calculated by dividing the 3M™ Steri-Gas™ EO Gas Cartridge nominal fill weight by the 3M™ Steri-Vac™ Sterilizer/Aerator GSX Series chamber volume. Data supplied above is based on an empty chamber.
Table 1. Preprogrammed Critical Cycle Parameters for GSX Series Sterilizers
4
The 3M™ Steri-Vac™ Sterilizer/Aerator GSX Series’ ethylene oxide (EO) sterilization cycles consist of ten stages. After the sterilization cycle is complete, an aeration cycle is required to remove any residual EO from the medical devices per manufacturers’ instructions for use (IFUs). An EO sterilization cycle is defined as a treatment in a sealed, temperature-controlled chamber comprised of air removal, conditioning, and injecting of EO, exposure to EO, removal of EO and flushing, aerating, and air admission allowing the opening of the chamber door. Figure 1 is a graph of a Pressure Profile of the cycle stages of a GSX Series sterilizer EO sterilization cycle. 10. Air Admission
Atmospheric Pressure
1. Chamber Preheating
Pressure
9. Aeration
6. EO Exposure 2. Air Removal
8. Flushing 5. EO Injection
3. Chamber Test
7. EO Removal
4. Conditioning
Time
Figure 1. Pressure Profile GSX Series Sterilizer EO Sterilization Cycle
2. Intended Use The 3M™ Steri-Vac™ Sterilizer/Aerator GSX Series is intended for the development and validation of ethylene oxide (EO) sterilization process parameters used in product development and manufacturing and for routine sterilization of products that require 100% ethylene oxide sterilization in the manufacturing process. The GSX Series sterilizer is not intended for use in health care facilities. Always obtain, understand, and follow national and local regulations before installing a GSX Series sterilizer.
CAUTION: To reduce the risk of injury, always follow the procedures described in this manual.
5
3M™ Steri-Vac™ Sterilizer / Aerator GSX Series – Operator’s Manual
3. Safety The 3M™ Steri-Vac™ Sterilizer/Aerator GSX Series was developed with the safety of operators and patients in mind. The GSX Series sterilizers are designed with state-of-the-art safety features that include: • Hardware and mechanical components of the GSX Series sterilizers meet or exceed the compliance requirements of current, recognized national and international safety standards including applicable sections of IEC 61010-1 (2010), IEC 61010-2-010 (2014), IEC 61010-2-040 (2015), ANSI/AAMI ST24, and EN1422. • The sterilization process is performed completely under a vacuum. If the system integrity is compromised during ethylene oxide (EO) gas exposure, room air will enter the chamber. In this situation, the system will detect a rise in pressure and will safely cancel the cycle when the system cannot maintain a vacuum. Sterilization and aeration can be conducted within the same chamber. Aeration in the sterilization chamber eliminates the need to transfer product loads outside the sterilization chamber when longer aeration times are required. • EO sterilant is delivered in single-dose cartridges placed inside the sterilization chamber. The use of single-dose cartridges reduces the risk of leaking ethylene oxide delivery lines and EO tank changes and provides increased control of sterilant quality. • GSX Series sterilizers are designed with an internal processor that automatically controls and independently monitors the physical process parameters to ensure sterilization conditions are maintained throughout the sterilization cycle. The GSX Series sterilizers’ embedded software regulates, independently monitors, and records critical sterilization process parameters including pressure, temperature, and percent relative humidity (%RH) during conditioning. • Automatic fault notification and safe state recovery processes provide additional protection for the Operator. If the GSX Series sterilizer detects a cycle fault, an error message will alert the Operator. Additionally, an optional audible notification will accompany the error code message. Immediately after detecting a fault, the GSX Series sterilizer will automatically complete an error recovery process to bring the sterilizer to a safe-state prior to further action. • GSX Series sterilizers are designed with a state-of-the-art proprietary humidification process. In the Conditioning stage of the sterilization cycle, GSX Series sterilizers contain a custom 3M designed humidification process that adds, measures, adapts, and controls %RH to accommodate different loads and packaging materials to achieve proper humidification prior to EO gas injection. • Control and monitor sensors detect critical sterilization process parameters. GSX Series sterilizers have control sensors for temperature, %RH, and pressure that provide information to the control embedded software. The sterilizer has a duplicate set of monitoring sensors that provide independent data and performance monitoring to an independent monitoring processor during critical sterilization stages for temperature, %RH, and pressure. • Over-the-door vent hood (i.e. exhaust hood) supplements the room’s directional air flow, and draws air away from Operators removing a load from the chamber. • The GSX Series sterilizers are designed with a specialized disposal cycle for full damaged, expired, or excess 3M™ Steri-Gas™ EO Gas Cartridges. The Cartridge Dispose Cycle is a custom, abbreviated cycle that safely empties and aerates the Steri-Gas EO Gas Cartridges at a rate of one per cycle. Disposal cycles have restricted access to a Supervisor PIN only. The GSX Series sterilizers and their related devices and accessories are designed to provide safe and reliable service when used according to the provided instructions for use. Please read, understand, and follow all safety information contained in the instructions for use prior to using a sterilizer. Use this equipment only for the purpose described in this Operator Manual. Retain these instructions for future reference. If this equipment is used in a manner not specified, the protection provided by the equipment may be impaired. It is the user’s facility management’s responsibility to ensure that all personnel who operate or maintain the equipment are trained in its operation and safe use. There are no formal safety inspections required by the Operator. It is the user’s facility management’s responsibility to assure safety inspections are complete. Contact your local 3M Health Care service personnel or authorized 3M service personnel for required safety inspections. The user‘s facility management has the responsibility to provide Operators and staff with the appropriate mitigations for safety regarding the configuration of the process parameters and the operation of the 3M™ Steri-Vac™ Sterilizer/Aerator GSX Series. These mitigations include end user validation of custom cycles and the identification, training, and use of appropriate protective measures (e.g. engineering controls, work practices, or personal protective equipment (PPE)); instruction for use of the equipment, with custom process parameters as defined by the end user, and comprehensive instruction regarding ethylene oxide (EO), including information on relevant health hazards, national regulations, methods for safe use, and methods to detect escape of the agent.
DANGER: To reduce the risks associated with exposure to ethylene oxide: Short term exposure limits (STEL) or long term exposure limits (LTEL) or immediately dangerous to life or health (IDLH) levels could be exceeded during NORMAL use. The user’s facility management is responsible for providing Operators, staff, and personnel working with 3M™ Steri-Vac™ Sterilizer/Aerator GSX Series equipment comprehensive instructions in the process. This instruction includes information on relevant health hazards. It is the user’s facility management’s responsibility to ensure that all personnel working with toxic chemicals, gases, and vapors are given comprehensive instruction in their use. This instruction includes information on relevant health hazards, national regulations, methods for safe use, and methods to detect the escape of the agent. It is the user’s facility management’s responsibility to ensure regular training of all personnel involved with the operation and maintenance of the equipment, including emergency procedures for any toxic, flammable, or explosive material released into the environment and to maintain records of attendance and evidence of demonstrated understanding from training sessions. National regulation regarding limitations on airborne EO concentration in the workplace exist in the United States. Many countries outside of the US have regulations regarding limitations of EO concentration the workplace as well. User’s facility management shall identify and validate appropriate engineering controls, work practices, personal protective equipment (PPE) and training requirements for Operators and staff prior to running a custom cycle. Prior to the user’s facility management exposure assessment, EO levels may be at or above IDLH (Immediately Dangerous to Life or Health) limits. User’s facility management shall provide protective measures in accordance with United States 29 CFR 1910.134 and 29 CFR 1910.1047 until validation of facility procedures that meet national, state, and local requirements for short term exposure limits (STELs) and long term exposure limits (LTELs). Good practice should include a risk analysis of the EO gas sterilization processes, a written Emergency Response Plan, and an Employee Notification plan for EO leaks. The following warnings and precautions should be observed to avoid unsafe actions that could result in personal injury or damage to the instrument.
6
4. Dangers and First Aid DANGER: Potential health effects of ethylene oxide Users in the United States must follow the requirements of the United States Occupational Exposure Standard for Ethylene Oxide OSHA (29 CFR 1910.1047). 100% ethylene oxide (EO) CAS number 75-21-8 is a colorless gas at ambient conditions. Do not rely on sense of smell for the detection of ethylene oxide. EO has a high odor threshold and can only be detected by sense of smell when it exceeds 500 - 750 parts per million (PPM). EO has a characteristic ether-like odor (i.e. a sweet and irritating solvent smell).
4.1. Dangers
DANGER: To reduce the risks associated with exposure to ethylene oxide: Short term exposure limits (STEL) or long term exposure limits (LTEL) or immediately dangerous to life or health (IDLH) levels could be exceeded during NORMAL use. The user’s facility management is responsible for providing Operators, staff, and personnel working with 3M™ Steri-Vac™ Sterilizer/Aerator GSX Series equipment comprehensive instructions in the process. This instruction includes information on relevant health hazards. Short term exposure limits (STEL) or long term exposure limits (LTEL,) or immediately dangerous to life or health (IDLH) limit could be exceeded during NORMAL use. Operators and staff must use protective measures (e.g. engineering controls, work practices, or personal protective equipment (PPE)) in accordance with United States 29 CFR 1910.134 and 29 CFR 1910.1047 under NORMAL use conditions until the user’s facility management completes an exposure assessment on each custom cycle validating facility protective measures meet national, state, and local requirements for short term exposure limits (STELs) and long term exposure limits (LTELs). Ensure Operator selects the correct cycle for the intended application. Ensure a minimum of ten (10) air exchanges per hour (ACH’s) for the room in which the 3M™ Steri-Vac™ Sterilizer/Aerator GSX Series is installed. Inspect display screen and cycle reports for error codes and listen for audible notifications (if enabled). Always take action for error codes as indicated in this manual. For reusable device sterilization, always follow device manufacturer’s instructions for use (IFU), including device cleaning, drying, packaging, sterilizing, and aerating. Do not overload the sterilization chamber. Use good practices for loading the sterilizer chamber. Never use force to access the inside of the sterilization chamber. Always review the elapsed aeration time on the 3M™ Steri-Vac™ Sterilizer/Aerator GSX Series display prior to opening the sterilizer door. Always inspect cycle reports (printout or electronic) to ensure the total aeration time matches the device manufacturer’s instructions for use (IFU) or as programmed by the Operator. Do not operate the 3M™ Steri-Vac™ Sterilizer/Aerator GSX Series outside specified environmental conditions as stated in this manual. Only use 3M™ Steri-Gas™ EO Gas Cartridges as listed in this manual. Do not use other brands or types of sterilant cartridges. Do not force the 3M™ Steri-Gas™ EO Gas Cartridges into the cartridge holder as excessive force could damage the cartridge and result in a cartridge leak. Do not use damaged 3M™ Steri-Gas™ EO Gas Cartridges. If an individual 3M™ Steri-Gas™ EO Gas Cartridge is ever dropped, the cartridge should be used immediately or disposed of as described in the cartridge disposal section of this manual. Sterilize only medical devices manufactured with materials compatible with ethylene oxide (EO) sterilization processes. Do not sterilize leather, liquids, or materials reactive to EO. Ensure that the compressed air supply is clean, with a maximum allowable dirt particle size of 0.5 microns, and that the air supply is free of oil. Ensure that the air filters on the compressed air supply contain a water trap and are cleaned daily (if applicable) and are properly maintained. Call 3M Health Care service personnel or authorized 3M service personnel immediately if there is a failure of the display or backlight and the sterilizer continues to operate. It is the user’s facility management’s responsibility to ensure that all personnel working with toxic chemicals, gases, and vapors are given comprehensive instruction in their use. This manual includes information on relevant health hazards, national regulations, methods for safe use, and methods to detect escape of the agent. It is the user’s facility management’s responsibility to ensure regular training of all personnel involved with the operation and maintenance of the equipment, including emergency procedures for any toxic, flammable, or explosive material released into the environment and to maintain records of attendance and document evidence of demonstrated understanding from training sessions.
7
3M™ Steri-Vac™ Sterilizer / Aerator GSX Series – Operator’s Manual 4.2. First Aid Inhalation: Move person to fresh air and seek medical attention.
Skin or Clothing Contact: Immediately wash with soap and water. Remove contaminated clothing and wash clothing before reuse. If signs/symptoms develop, seek medical attention.
Eye Contact: Immediately flush with large amounts of water for at least 15 minutes. Remove contact lenses if easy to do so. Continue rinsing. Immediately seek medical attention.
If Swallowed: Rinse mouth. DO NOT INDUCE VOMITING. Immediately seek medical attention.
Hazard statements of ethylene oxide (EO): • Extremely flammable gas • Contains gas under pressure, may explode if heated • Toxic if inhaled • Causes serious eye irritation • May cause drowsiness or dizziness • Suspected of damaging fertility or an unborn child • May cause cancer • May cause genetic defects
Consult the 3M™ Steri-Gas™ EO Gas Cartridge Safety Data Sheet (SDS) for additional information (www.3M.com).
8
5. Warnings WARNING: To reduce the risks associated with fire and explosion: 3M™ Steri-Gas™ EO Gas Cartridges contain 100% ethylene oxide (EO) which is an extremely flammable gas and a liquid under pressure. Do not use near flame, electrical sparks, hot surfaces, or allow sources of ignition near the cartridges. Do not puncture cartridge outside the sterilization chamber. Do not incinerate cartridges. Exposure to temperatures above 150ºF (65.5ºC) may cause cartridge to burst. 3M™ Steri-Gas™ EO Gas Cartridge Catalog Number
3M™ Steri-Vac™ Sterilizer GSX Series Model
Nominal Net Weight of Ethylene Oxide (EO)
4-100
GS5X or GS8X
EO net wt. 100 g. (3.52 oz.)
8-170
GS8X
EO net wt. 170 g. (5.99 oz.)
4-134
GS5X or GS8X
EO net wt. 127 g. (4.47 oz.)
4-60
GS5X or GS8X
Custom EO net wt.
Do not sterilize devices with energy sources which could create a spark in the sterilization chamber during the sterilization cycle. For reusable device sterilization, always follow device manufacturer’s instructions for use (IFU), including device cleaning, drying, packaging, sterilization, and aeration. Inspect display screen and cycle reports for error codes and listen for audible notifications (if enabled). Always take action with error codes as indicated in this manual. Do not attempt to access any internal mechanisms of the 3M™ Steri-Vac™ Sterilizer/Aerator GSX Series. Operators should not service the GSX Series sterilizer as there are no user serviceable parts.
WARNING: To reduce the risk of shock due to hazardous voltage: Do not attempt to access any internal mechanisms of the 3M™ Steri-Vac™ Sterilizer/Aerator GSX Series. Operators should not service the GSX Series sterilizer as there are no user serviceable parts. Customer must provide a properly grounded outlet (an earth ground) for installation as described in the installation requirements section of this manual. Do not use a detachable cord rated less than 15A. Do not operate the 3M™ Steri-Vac™ Sterilizer/Aerator GSX Series outside the environmental conditions as stated in this manual. Use only 3M Health Care service personnel or authorized 3M service personnel for installation and maintenance. Do not modify any part of 3M™ Steri-Vac™ Sterilizer/Aerator GSX Series.
9
3M™ Steri-Vac™ Sterilizer / Aerator GSX Series – Operator’s Manual
6. Cautions CAUTION: To reduce the risk of injury: Always follow the procedures described in this manual. Follow good ergonomic practices. Loading baskets should not be overfilled requiring excessive force in pulling and pushing loaded baskets in and out of the sterilizer chamber. Reference facility policies and procedures for appropriate ergonomic practices.
CAUTION: To reduce patient risks associated with exposure to potentially non-sterile devices or inadequate sterilization procedures: The user must validate the sterile efficacy of each custom cycle intended to sterilize products that are labeled as ‘Sterile’. Ensure Operator selects the correct cycle for the intended application. Inspect display screen and cycle reports for error codes and listen for audible notifications (if enabled). Always take action for error codes as indicated in this manual. Always use chemical indicators and biological indicators for monitoring the performance of sterilization cycles as described in this manual. Always use chemical indicators and biological indicators per the device manufacturer’s instructions for use (IFU). Always inspect cycle reports (printout or electronic file) to ensure the Operator’s programmed parameters or the device manufacturer’s instructions for use (IFU) matches: • %RH at the End of Conditioning, • Temperature at the End of Conditioning, • Actual Gas Exposure Time. Complete maintenance at routine scheduled intervals of a maximum of every six (6) months. There are no user-serviceable parts. Only use 3M Health Care service personnel or authorized 3M service personnel for maintenance. For reusable device sterilization, always follow device manufacturer’s instructions for use (IFU), including device cleaning, drying, packaging, sterilization, and aeration. Do not overload the sterilization chamber. Use good practices for loading the sterilizer chamber. Sterilize only medical devices manufactured with materials compatible with ethylene oxide (EO) sterilization processes. Do not sterilize leather, liquids, or materials reactive to EO. Only use 3M™ Steri-Gas™ EO Gas Cartridges as listed in this manual. Do not use other brands or types of sterilant cartridges. Do not force the 3M™ Steri-Gas™ EO Gas Cartridges into the cartridge holder. Excessive force could damage the cartridge and result in a cartridge leak. Do not operate the 3M™ Steri-Vac™ Sterilizer/Aerator GSX Series outside the environmental conditions as stated in this manual. Immediately call 3M Health Care service personnel or authorized 3M service personnel if there is a failure of the display or backlight and the GSX Series sterilizer continues to operate. Do not modify any data or records from the sterilizer system which may lead to misinterpretation of physical monitor results. Do not place any device emitting strong electronic magnetic fields (EMFs) near the sterilizer.
10
7. Specifications 7.1. 3M™ Steri-Vac™ Sterilizer/Aerator GSX Series Structural Specifications GS5X
GS8X
Operational Weight
127 kg (281 lbs.) single door 132 kg (290 lbs.) double door
261 kg (576 lbs.) single door 269 kg (593 lbs.) double door
Exterior Dimensions
H 70.9 cm x W 76.2 cm x D 95.0 cm H 27.9 in. x W 30.0 in. x D 37.4 in.
H 179.8 cm x W 94.0 cm x D 109.0 cm H 70.8 in. x W 37.0 in. x D 42.9 in.
Chamber Internal Volume
136 L (4.8 cubic feet)
224 L (7.9 cubic feet)
Chamber Internal Dimensions
H 38.0 cm x W 43.0 cm x D 83.0 cm H 15.0 in. x W 17.0 in. x D 32.5 in.
H 46.0 cm x W 51.0 cm x D 97.0 cm H 18.0 in. x W 20.0 in. x D 38.0 in.
7.2. Sound Power Levels Specifications The average decibel level of an active GS5 or GS8 sterilizer is <60 dBA. For more information on sound levels, in the US contact 3M Health Care Helpline at 1-800-228-3957. Outside the US contact your local 3M office or to locate your local office go to www.3M.com
7.3. Power Specifications
WARNING: To reduce the risk of shock due to hazardous voltage, the customer must provide a properly grounded outlet (an earth ground) for installation as described in the installation requirements section of this manual. Do not use a detachable cord rated less than 15A.
CAUTION: To reduce patient risks associated with exposure to potentially non-sterile devices or inadequate sterilization procedures, do not place any device emitting strong electronic magnetic fields (EMFs) near the sterilizer.
Electrical Power
Operating Condition
Units
Voltage Range
200 - 240
VAC
Frequency
50/60
Hertz
Phase
Single
Not Applicable
GS5X Current
10
Amps
GS8X Current
12
Amps
11
3M™ Steri-Vac™ Sterilizer / Aerator GSX Series – Operator’s Manual 7.4. Air Supply Specifications
DANGER: To reduce the risks associated with exposure to ethylene oxide, ensure that the compressed air supply is clean, with a maximum allowable dirt particle size of 0.5 microns, and that the air supply is free of oil. Ensure that the air filters on the compressed air supply contain a water trap and are cleaned daily (if applicable) and are properly maintained.
Air Supply Feature
Specification
Pressure
7.0 kg/cm2 (100 psig) minimum to 10.5 kg/cm2 (150 psig) maximum
Flow Rate
2.2 liters per second at 7.0 kg/cm2 (4.7 standard cubic feet per minute at 100 psig) per sterilizer based on 100% duty cycle compressor
Quality
Clean air supply with a maximum allowable dirt particle size of 0.5 microns and free of oil
Moisture Content
Less than 10°C (50°F) dew point
8. Compliance and Reference Standards 8.1. Device Safety Compliance Ethylene oxide (EO) sterilizers, for use in industrial applications, (i.e. outside a health care facility) are not regulated as medical devices by the United States FDA; therefore, they are not eligible for 510(k) review and clearance. The 3M™ Steri-Vac™ Sterilizer/Aerator GSX Series complies with the following standards as demonstrated by the CB Scheme Certificate and test report issued by the Underwriters Laboratories (UL): • IEC / EN 61010-1 (2001, 2010, CSA 2nd Ed:2008, 2nd Ed:2013, 3rd Ed:2012) Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 1: General requirements. • IEC / EN 61010-2-010 (2003, 3rd Ed:2014) Safety requirements for electrical equipment for measurement, control and laboratory use - Part 2-010: Particular requirements for laboratory equipment for the heating of materials. • IEC / EN 61010-2-040 (2005, 2015) Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-040: Particular requirements for sterilizers and washer-disinfectors used to treat medical devices. The following clauses were not evaluated as part of the IEC 61010-2-040: Clause 13.1, 13.1.101.2, 13.1.101.4, 13.1.102, 13.1.103.2, 13.1.103.3, 13.101. The 3M™ Steri-Vac™ Sterilizer/Aerator GSX Series is listed as Laboratory Electrical Equipment for Use in Health Care Applications (Certified for Canada) and carries the UL mark with adjacent indicators “C” and “US” based on compliance to the standards UL 61010-1 and CAN/CSA 22.2 No. 61010-1. The 3M™ Steri-Vac™ Sterilizer/Aerator GSX Series complies with the CE mark related to the Low Voltage Directive (LVD) 2006/95/EC as confirmed in the Declaration of Conformity. The 3M™ Steri-Vac™ Sterilizer/Aerator GSX Series complies with the RoHS Directive, Directive 2011/65/EU of the European Parliament and of the Council on the restriction of the use of certain hazardous substances in electrical and electronic equipment. In the European Union, the 3M™ Steri-Vac™ Sterilizer/Aerator GSX Series are certified as exempt from the scope of the ATEX Directive.
8.2. Electromagnetic Compatibility (EMC) Compliance The 3M™ Steri-Vac™ Sterilizer/Aerator GSX Series complies with the following EMC standards as confirmed in the Certificate of Compliance generated by 3M: IEC 61326-1 Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 1: General requirements. The 3M™ Steri-Vac™ Sterilizer/Aerator GSX Series complies with the EMC requirements of the CE mark EMC Directive 2004/108/EC. The 3M™ Steri-Vac™ Sterilizer/Aerator GSX Series complies with the Australian EMC requirements as confirmed in the Supplier’s Declaration of Conformity that is linked to the RCM Mark. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide a reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates and can radiate radio frequency energy; and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his/her own expense. In addition, operation of this device must accept any interference received, including interference that may cause undesired operation. This Class A digital equipment meets all requirements of the Canadian Interference-Causing Equipment Regulations.
12
9. Installation and Set Up To ensure proper operation of this equipment and Operator safety, the 3M™ Steri-Vac™ Site Planning and Installation Guide must be followed and the equipment must be installed by authorized 3M service personnel. To arrange installation, contact your local 3M subsidiary (www.3m.com)
WARNING: To reduce the risk of shock due to hazardous voltage, only use 3M Health Care service personnel or authorized 3M service personnel for installation and maintenance.
9.1. Environmental Operating Conditions
DANGER: To reduce the risks associated with exposure to ethylene oxide, do not operate the 3M™ Steri-Vac™ Sterilizer/Aerator GSX Series outside the environmental conditions as stated in this manual.
WARNING: To reduce the risk of shock due to hazardous voltage, do not operate the 3M™ Steri-Vac™ Sterilizer/Aerator GSX Series outside the environmental conditions as stated in this manual.
CAUTION: To reduce patient risks associated with exposure to potentially non-sterile devices or inadequate sterilization procedures, do not operate the 3M™ Steri-Vac™ Sterilizer/Aerator GSX Series outside the environmental conditions as stated in this manual.
Environmental Condition
Operating Condition
Units
Altitude
2500 (max)
Meters
*Operating Temperature
15 - 35
ºC
Operating Relative Humidity
20 - 80 (non-condensing)
%RH
Installation/ Transient Over Voltage Pollution Degree
Category II 2
*Note: Operating the 3M™ Steri-Vac™ Sterilizer/Aerator GSX Series in a temperature environment that is close to the sterilization process temperature set point (e.g. 35ºC operating environment and a 38ºC sterilization process temperature set point) may result in a temperature fault during the sterilization process.
13
3M™ Steri-Vac™ Sterilizer / Aerator GSX Series – Operator’s Manual 9.2. Room and Installation Requirements
DANGER: To reduce the risks associated with exposure to ethylene oxide, ensure a minimum of ten (10) air exchanges per hour (ACHs) for the room in which the 3M™ Steri-Vac™ Sterilizer/Aerator GSX Series is installed.
Location
Do not place the sterilizer or ethylene oxide (EO) cartridges in an area of possible ignition sources. ONLY USE INDOORS.
Room Size
Greater than 30m3 (1,000 ft3)
Spacing
Allow 51cm (20 inches) of clearance space at the top, rear, and sides of the sterilizer for maintenance and service and a minimum of 10 cm (4 inches) from the rear wall for single door units. Ensure sufficient space
Ventilation
Negative pressure with a minimum of ten (10) air exchanges per hour. The ventilation system should be non-recirculating and dedicated.
Air Flow
Air flow washes the entire room. Air movement is away from the sterilizer Operator. See Figure 2.
ACCEPTABLE or
UNACCEPTABLE Exhaust
Exhaust
Intake
Exhaust Sterilizer
Sterilizer Intake
“Dead” Air Space
Air flow washes entire room. Air movement is away from operator.
Air movement is toward operator and “dead” air spaces can form.
Figure 2. Acceptable and Unacceptable Installation Air Flow
14
9.3. Set up and Connections Figures 3 - 7 illustrate the components and connections for the 3M™ Steri-Vac™ Sterilizer/Aerator Series, Models GS5X and GS8X. Table 3 contains additional details regarding specific components and connections for the GSX Series Models GS5X and GS8X.
Chamber Door Touch Screen & Display Water Reservoir, Printer & USB Ports Access Door Cartridge Scanner Bay Printer & USB Ports Access Door Water Reservoir Access Door
Figure 3. Front View 3M™ Steri-Vac™ Sterilizer/Aerator GSX Series, Models GS5X & GS8X
4. Abator (optional) 3. Ethernet (optional) 2. Power Switch
6. Chamber Exhaust (Ethylene Oxide Vent Line)
1. Power Cord 5. Air Inlet
Figure 4. Left Side Connections 3M™ Steri-Vac™ Sterilizer/ Aerator GSX Series
15
3M™ Steri-Vac™ Sterilizer / Aerator GSX Series – Operator’s Manual 7. Vent Hood Exhaust
Figure 5. Top Connection - 3M™ Steri-Vac™ Sterilizer/Aerator GSX Series
8. User Screen
9. USB Ports 10. EO Gas Cartridge Barcode Scanner
11. Printer w/ Paper
12. Distilled Water Reservoir
Figure 6. Front Panel, 3M™ Steri-Vac™ Sterilizer/Aerator GSX Series, Model GS8X
8. User Screen
16
11. Printer w/ Paper
9. USB Ports
12. Distilled Water Reservoir
10. EO Gas Cartridge Barcode Scanner
Figure 7. Front Panel, 3M™ Steri-Vac™ Sterilizer/Aerator GSX Series, Model GS5X
Connection or Component Number
Connection or Component Name
1
Power Cord
Use the supplied power cord for connection of the system to a properly grounded outlet as specified in the 3M™ Steri-Vac™ Site Planning and Installation Guide. Ensure there is adequate space at installation to disconnect the power cord when required. Do not use a detachable cord rated less than 15A
2
Power Switch
The power switch turns power to the GSX Series sterilizer OFF and ON. The switch is intended to remain ON at all times in order to simplify operation and to allow the sterilizer electronics to continually monitor sterilizer functions. It is recommended to keep the power ON at all times unless otherwise instructed by 3M Health Care service personnel or authorized 3M service personnel.
Ethernet
The Ethernet connection is not required for normal operation of the system. Connecting to Ethernet provides 3M Health Care Service with a means to access Service diagnostic information on the GSX Series sterilizer from a desktop computer located on-site within the clinic network. 3M Health Care Service can access cycle information, reports (e.g. calibration, site setup) and service diagnostic information directly on the sterilizer. Devices connected to the Ethernet port must be 60950-1 (General Requirements for Information Technology Safety) compliant. Do not connect devices that are not compliant to 60950-1. Reference Chapter 13 for additional information.
4
Abator
The Abator connection is only provided for connection to an emission control device (i.e. an EO Abator), only if such a device is required by local laws/codes. Do not connect any other device to this connector. Abator connection is for sterilizer communication to an emission control device. Abator installation may be optional and not required for the normal operation of the system but is required in some localities. The Abator connection is intended to only be made by 3M Health Care service personnel or authorized 3M service personnel during installation.
5
Air Inlet
Air inlet is for the connection of the compressed air supply per Chapter 9 and is intended to only be made by 3M Health Care service personnel or authorized 3M service personnel.
6
Chamber Exhaust (Ethylene Oxide Vent Line)
Connect the GSX Series sterilizer to a dedicated vent line in order to exhaust ethylene oxide (EO) to the outside atmosphere or to an emission control device, an EO Abator. The requirements for venting the sterilizer must be met as documented in the 3M™ Steri-Vac™ Sterilizer/Aerator GSX Series Site Planning and Installation Guide and is intended to be made only by 3M Health Care service personnel or authorized 3M service personnel.
7
Vent Hood Exhaust
The over-the-door vent hood (i.e. exhaust hood) supplements the room’s directional air flow and is designed to draw air away from Operators removing a load from the chamber. The hood is connected by 3M Health Care service personnel or authorized 3M service personnel to a customer supplied dedicated exhaust system during installation of the sterilizer. The vent hood (i.e. exhaust hood) is monitored for an adequate standard cubic feet per minute (SCFM) air flow rate. If the sterilizer detects the air flow is too low (< 125 SCFM) through the vent hood, the sterilizer door will remain locked until a minimum of three (3) hours of aeration is fulfilled. Monitoring of the vent hood air flow is optional and can be disabled by an authorized 3M service provider in the Site Setup<Setup Tab - Options Set (Figure 24. Chapter 10). If vent hood monitoring is disabled, there will be no caution message if the air flow SCFM is too low (< 125 SCFM) and the sterilizer door will remain locked until a minimum of three (3) hours of aeration is fulfilled.
8
User Screen
User and display screen for the Operator interface with the sterilizer control features. See Chapter 10 for more details.
9
USB Ports
The USB ports are available for Universal Serial Bus (USB) drives to export multiple types of cycle reports, sterilizer and cycle settings, and to load and remove custom cycles programmed on the 3M™ Cycle Programmer. See Chapter 11 for more details. Recommended USB drives include drives with FAT32 formatting. Drives with pre-loaded software (e.g. SanDisk’s Cruzer®) are not recommended. Only USB drives, for the sole purpose of exporting and importing data and cycles, are to be connected to the USB ports. Do not connect external USB devices that supply power. See Chapter 11 for more details.
10
3M™ Steri-Gas™ EO Gas Cartridge Barcode Scanner
Location of cartridge scanner bay. Scanning the 3M™ Steri-Gas™ EO Gas Cartridge bar code ensures that the cartridge is valid for use. See Chapter 13 for more details.
11
Printer w/ Paper
The built-in printer provides easy-to-read information for each sterilization cycle. The printer can also be used to print multiple types of cycle reports, in addition to sterilizer and cycle settings. The cycle report printout is essential in analyzing the GSX Series sterilizer performance and can be retained to meet cycle verification policies. See Chapter 13 for more details.
12
Distilled Water Reservoir
Distilled water is used for humidification of the EO sterilization process. Ensure the distilled water reservoir is adequately filled. The GSX Series sterilizer will display an error message if the distilled water level is too low to run a sterilization cycle. Do not overfill water reservoirs.
Not Numbered
Location of the temperature sensor used for process control
The temperature sensor used for process control is located inside the sterilizer chamber, protruding from the right side chamber wall bottom section, towards the loading chamber door.
3
Connection or Component Description
Table 2. Sterilization Connection and Component Explanations
17
3M™ Steri-Vac™ Sterilizer / Aerator GSX Series – Operator’s Manual
10. Using the Touch Screen 10.1. Main Screen Figure 8 shows the Main Screen of the 3M™ Steri-Vac™ Sterilizer/Aerator GSX Series that appears after the power cycles ON. A double door sterilizer will have an additional button on the Main Screen for the option to open the Unload door. The Operator controls the 3M™ Steri-Vac™ Sterilizer/Aerator GS Series via a touch screen. A fingertip, stylus, ball tip pen or a computer mouse can be safely used to navigate the touch screens. To use a computer mouse, simply plug the mouse into one of the two USB ports (reference Figures 6 and 7) and the mouse arrow will appear on the touch screen. Sterilizer
22.2˚C
98.0 kPa
1
3
2
4
04/20/2015 05:19:51
5
6
7
Select cycle:
GSX 38C GSX 55C
Figure 8. GSX Series Sterilizer Main Screen Menu
Open door
10.2. Menu The Menu button in the bottom left hand corner is used to access the following options: Reports, Cycles, Setup, Status and Service. Figure 9 shows the Menu options screen. Sterilizer
22.2˚C
98.0 kPa
1
3
2
4
04/20/2015 05:19:52
5
6
7
Select cycle:
Reports
GSX 38C GSX 55C
Cycles Setup Status Service Menu
18
Open door
Figure 9. GSX Series Sterilizer Menu Options
10.3. Reports The 3M™ Steri-Vac™ Sterilizer/Aerator GSX Series has a variety of reporting options as shown in Figure 10. Sterilizer
22.2˚C
98.0 kPa
1
3
2
4
04/20/2015 05:19:53
5
6
7
Select cycle:
Cycles
GSX 38C Cycle reports GSXreport 55C EO usage
Setup
Site setup report
Status
Custom cycle set points
Service
Export cycle data
Reports
Figure 10. Reports Menu
Printer form feed Menu
Open door
10.3.1. Cycle Reports Figure 11 outlines the options for 3M™ Steri-Vac™ Sterilizer/Aerator GSX Series Cycle Reports. Sterilizer Print or export report
22.2˚C
04/20/2015 12:29:13
98.0 kPa
Cycle 33 - 4/20/2015 - Stent 126 Cycle 32 - 4/20/2015 - Stent 126 Cycle 31 - 4/19/2015 - Stent 126 Cycle 30 - 4/19/2015 - Stent 126 Cycle 29 - 4/18/2015 - Scope 395 Cycle 28 - 4/17/2015 - Scope 395 Cycle 27 - 4/17/2015 - Scope 395 Cycle 26 - 4/16/2015 - GSX 55C Cycle 25 - 4/16/2015 - GSX 55C
Print selected cycle Export selected cycle Export all cycles Report format Graph Control sensors
Monitor sensors
Temperature
Temperature
Pressure
Pressure
Relative humidity
Relative humidity
Figure 11. Cycle Report Setup Enter Pin
Return
OK
Reports from the last 100 cycles can be printed or exported electronically to a USB drive. When the 100 cycle limit is reached, the oldest cycles are replaced with the most recently run cycles. Select the desired cycle(s) from the list of the last 100 cycles (sorted with the most recently run cycles at the top) and select the desired function from the following options: print selected cycle, export selected cycles, or export all cycles. Only one cycle may be selected for printing. Multiple cycles can be selected for export to a USB drive. To export electronic reports, insert a USB drive (data storage device) into one of two USB ports on the GSX Series sterilizer. Recommended USB drives include those with FAT32 formatting. USB drives with pre-loaded software (e.g. SanDisk’s Cruzer®) are not recommended. Connect only USB drives for the export of data to the USB ports. Do not connect external USB devices that supply power to the USB ports. Select the cycle(s) for which you wish to export reports and press the OK button. The selected reports are stored in the USB directory selected by the user. The sterilizer will ask for confirmation of the Folder designation before export. The electronic reports are generated in color and are sized as 20.3 cm (8 in.) x 27.9 cm (11 in.) images and contain the same information as the strip chart reports. The GSX Series sterilizer has control sensors for temperature, %RH, and pressure that provide information to the control embedded software. In addition, the sterilizer has a duplicate set of monitoring sensors that provide independent data and performance monitoring during critical sterilization stages for temperature, %RH, and pressure. The sterilizer defaults to report only on the control sensors. Monitoring sensors can be selected for reporting in the Cycle Report options screen in Figure 11. 19