AKRON
ARJOHUNTLEIGH Patient Hoists and Transport Systems
ARJOHUNTLEIGH Lifeguard Model LG50 Assembly Spares Manual Oct 2011
746-168-5Assembly Spares Manual
33 Pages
Preview
Page 1
APPENDIX A – ASSEMBLY SPARES MANUAL A.1
General
The Assembly Spares Manual is for the identification and requisition of replaceable parts. It contains assembly drawings of the equipment and sub-assemblies. Each drawing sheet is accompanied by its related parts list. Sometimes a number of identical parts may appear in different locations but only one will be identified with a balloon. The number in the “Qty” column of the parts list indicates the total number of times that the part appears in the drawing. A.2
How to Use the Assembly Spares Manual
Find the equipment serial number on the product specification label. Cross-reference the serial number with the modification list on the next page to ensure the assembly drawings correspond to the build level of the equipment.
A-1
746-168-5 10/2011
Form 130/2
Service Manual Amendments Sheet Document Ref. 746-168 Product – Lifeguard® LG50 & NLG50 Trolleys Build Level
Mod Note
Date
Serial No.
31
4307
10.06.05
756153
32
4350
11.08.05
756153
33
4804
06.08.07
756153
34 35 36 37
4889 4895 4972 5026
19.12.07 03.01.08 14.04.08 20.06.08
38
5114
05.11.08
39
WE05182
03.02.09
40 41 42 43 44 45 46 47 48 49 50
WE05210 WE05200 WE10030 WE10045 WE05199 WE10062 WE10079 WE10095 WE10165 WE10280 WE10261
26.02.09 05.03.09 18.03.09 20.03.09 24.03.09 17.04.09 12.05.09 15.05.09 28.07.09 15.12.09 11.03.11
P037229 P046913 P______ P098118
51
WE10592
26.07.11
P0102092
Form 130-2 Service Manual Amendments Sheet_LG50.doc
Sheet No.
Drawing No.
Issue
6 7 100 6 7 13 2 2 5 2 3 5 8 10 11 13 2 5 13 11 2 2 2 2 8 5 3 2 1 1 2 5 6 7 8 13
799.00 799.01 805.484 799.00 799.01 799.360 799.110 799.110 799.97 799.110 761.230 799.97 799.103 799.429 801.06 799.360 799.110 799.97 799.360 801.06 799.110 799.110 799.110 799.110 799.103 799.97 761.230 799.110 799.503 799.503 799.110 799.97 799.00 799.01 799.103 799.360
6 6 2 7 7 5 10 11 12 12 4 13 9 6 4 6 13 14 7 5 14 15 16 17 10 15 5 18 4 5 19 16 8 8 11 8
26/07/2011
i r P n e h W t n e m u c o D d e l l o r t n o c n U
d e t n
PDF processed with CutePDF evaluation edition www.CutePDF.com
U
c n
t n o
d e l l ro
d e t ir n P n e h W t n e m u c o D
e l l o r t n o c n U
D d
c o
i r P n e h W t n e m u
d e t n
D d e l l o r t n o c n U
u c o
n e m
W t
i r P n e h
d e t n
PDF processed with CutePDF evaluation edition www.CutePDF.com
U
o c n
o r nt
d e ll
o D
n e m cu
d e t ir n P n e h W t
i r P n e h W t n e m u c o D d e l l o r t n o
d e t n
i r P n e h W t n e m u c o D d e l l o r t n o c n U
d e t n
PDF processed with CutePDF evaluation edition www.CutePDF.com
U
N
O C
N
TR
O
L
D E L
D
O
C
U
M
T N E
EN H W
D E T N I R P
14
11 / 7 /0
N C O N TR O LL ED
U
D O C U M EN T W H EN
PR IN TE D
14 /0 7/ 11
APPENDIX B – DISPOSAL OF GAS SPRINGS The gas spring contains air and oil at high pressure and must be vented in accordance with the following instructions before being discarded. Under no circumstances should any attempt be made to open the device.
WARNING Danger of explosion. Do not heat or incinerate. High pressure gas. The sudden release of gas at high pressure could cause serious injury or death. Put on suitable protective clothing, eye protection and / or a face shield. 1. Operate the valve at the end of the piston rod and allow the piston rod to extend fully. 2. Clamp the gas spring in a vice and drill a hole approximately 3 mm diameter at position 1 as shown in Fig. B-1. Screen off the drilling point because metal chips and oil may be ejected due to the high internal pressure. Then drill a second hole at position 2 as shown. the holes should be drilled to a depth of approximately 10 mm
Disposal of gas spring 3. Operate the valve at the end of the piston rod and push in the piston rod. 4. Drain oil from the gas spring by pumping the piston rod in and out several times. 5. Dispose of the gas spring and oil through raw materials trade or special refuse points. Do not dispose of gas springs or oil in household refuse. If correct disposal in accordance with these instructions is not possible, the unit should be returned to the supplier.
B-1
746-168-5 10/2011