Dual Incu i Quick Guide Model 100

Preparation Before Use

Radiant Warmer Mode

■ Switching on the Power . . . . . . . . . . . . . . . . . P .3

■ Heater Control . . . . . . . . . . . . . . . . . . . . . . . . P .7

■ Raising and Lowering the Hi-Low Stand . . . . P .3

■ Using the Timer . . . . . . . . . . . . . . . . . . . . . . . P .8

■ Switching Modes . . . . . . . . . . . . . . . . . . . . . . P .3

Incubator Mode

Other Operations ■ Setting the Pulse Oximeter Alarm . . . . . . . . . P .9

■ Setting Incubator Air Temperature/

■ Weighing the Infant . . . . . . . . . . . . . . . . . . . . P .10

Skin Temperature . . . . . . . . . . . . . . . . . . . . . P .4 ■ Adjusting the Humidity . . . . . . . . . . . . . . . . . . P .5 ■ Using the Oxygen Functions . . . . . . . . . . . . . P .6

[Control panel] ●Normal state

●When switched to message area

Message area

Message area

Screen display switch area

Mode switch

[Rear]

Sensor module

Humidity chamber cover

Foot switch

2

■ Switching on the Power Preparation Before Use

At the rear of the main body of the incubator: ① Insert the power cord in the AC inlet. ② Check that the breaker is on. ③ Turn the power switch on. ① Breaker

③

Power switch

AC inlet Power cord

② Breaker Normal position (ON)

Tripped position (OFF)

■ Raising and Lowering the Hi-Low Stand ● Step on the pedal of the foot switch to raise the Hi-Low stand.

When raising (

pedal)

● Step on the pedal of the foot switch to lower the Hi-Low stand.

When lowering (

pedal)

■ Switching Modes On the side of the main body of the incubator: ● Press and hold the

side of the mode switch to change to incubator mode.

● Press and hold the

for approximately two seconds to automatically switch to the radiant warmer mode.

Incubator mode

Radiant warmer mode

3

■ Setting Incubator Air Temperature/Skin Temperature ● Touch the temperature area to switch the message area.

● Select the control mode in the message area.

Incubator Mode

Servo Control

The incubator air temperature is automatically controlled to maintain the infant’s skin temperature.

Manual Control

The incubator air temperature is set manually.

Servo Control ● 37 .5°C or lower Set the skin temperature by touching the switches.

● 37 .6°C or higher (override mode) , then set the skin temperature Touch by touching the switches.

Memo If you set the temperature to 37.5°C or less, the override mode is automatically canceled.

● Touch

4

to close the message area.

Manual Control ● 37 .0°C or lower Set the incubator air temperature by touching the

switches.

● 37 .1°C or higher (override mode) , then set the incubator air temTouch perature by touching the switches.

Memo If you set the temperature to 37.0°C or less, the override mode is automatically canceled.

■ Adjusting the Humidity ● Make the necessary preparations.

① Open the humidity chamber cover and remove the cartridge tank. Humidity chamber

② Fill up the cartridge tank and replace it to its former position. Cartridge tank

Humidity chamber cover

Sterile distilled water Cartridge tank

Incubator Mode

● Touch the relative humidity area to switch the message area.

● Touch

in the message area for humidity control.

✽ To stop humidification, touch

.

● Adjust the humidity by touching the

● Touch

switches.

to close the message area.

5

■ Using the Oxygen Function ● Touch the oxygen area to switch the message area.

<Calibrating the oxygen sensor>

<Setting the Oxygen Concentration>

Incubator Mode

Calibrate the oxygen sensor before using the incubator . The oxygen sensor cannot be correctly calibrated while using the oxygen function .

● Touch in the message area to start the oxygen function.

Display the message area while the oxygen concentration is displayed in the oxygen area. ● Touch

in the message area.

● Set an oxygen concentration value by touching the

switches.

● The following message is displayed. ● Touch ● Pull the sensor module at the rear of the main body of the incubator slightly toward you. ① Release the sensor module lock. ② While pressing the lever, pull out the sensor module fully without removing it from the hood.

Lever

①

Sensor module

②

③ A message is displayed on the control panel and calibration is started.

● The message disappears when calibration is completed. Confirm that the message has disappeared, and return the sensor module to its original position.

6

to close the message area.

Stopping the Oxygen Function ● Touch

.

● Touch

.

■ Heater Control ● Touch the heat area to switch the message area.

● Select the control mode in the message area. Servo Control

The incubator air temperature is automatically controlled to maintain the infant’s skin temperature.

Manual Control

The heater output is set manually.

Servo Control ● 37 .5°C or lower Set the skin temperature by touching the

Manual Control ● Preheating Touch

.

switches.

● 37 .6°C or higher (override mode) , then set the skin temperature Touch by touching the switches.

mattress, and touch

Radiant Warmer Mode

Confirm that the infant is not placed on the .

● Set the heater output . Set the heater output by touching the switches.

Memo If you set the temperature to 37.5°C or less, the override mode is automatically canceled.

● Touch

to close the message area.

7

■ Using the Timer Apgar Timer

CPR Timer

● Starting the Apgar timer

● Starting the CPR timer

Touch the timer area, and the Apgar timer will start.

● Stopping the Apgar timer Touch the timer ar ea again while the timer is r unning, and a message to confirm whether to stop the timer will appear. Touch , and the timer will be stopped and reset.

● Touch

Radiant Warmer Mode 8

to close the message area.

Touch the timer area, and the CPR timer will start.

● Stopping the CPR timer Touch the timer ar ea again while the timer is r unning, and a message to confirm whether to stop the timer will appear. Touch , and the timer will be stopped and reset.

■ Setting the Pulse Oximeter Alarm ● Touch the SpO2 area or pulse rate area to switch the message area.

Pulse rate area SpO2 area

<Setting the SpO2 Upper Limit/Lower Alarm Limits>

<Setting the Pulse Rate Upper Limit/Lower Alarm Limits>

● Select the lower limit or upper limit for the alarm.

● Select the lower limit or upper limit for the alarm.

Touch limit.

for the lower limit, and

for the upper

● Set the upper or lower limit values by touching the

● Touch

switches.

to close the message area.

Touch limit.

for the lower limit, and

for the upper

● Set the upper or lower limit values by touching the

● Touch

switches.

to close the message area.

Setting the alarm to OFF

Touch the switch with the upper limit at 99%, or the switch with the lower limit at 45%. The numerical value is displayed as “- -” and the alarm is turned off.

Touch the switch with the upper limit at 240bpm, or the switch with the lower limit at 35bpm. The numerical value is displayed as “- - -” and the alarm is turned off.

Other Operations

Setting the alarm to OFF

9

■ Weighing the Infant Weights under 300g cannot be measured .

● Touch

in the screen display switch area to display the weight screen.

● Touch

, and measure the infant’s weight following the displayed instructions.

● Measurement is completed when the weight is displayed.

to record the weight, and touch ● Touch more to weigh the infant again.

once

If Measurement Was Not Correctly Completed

Other Operations 10

Someone may be leaning on the mattress platform, or the infant may be touching the mattress platform while tare weight measurement is in progress. Perform the tare weighing process again while taking care that nothing comes into contact with the mattress platform.

Repeat weighing by touching

If the infant is actively moving, he/she cannot be weighed. Weigh the infant again when he/she has settled down.

Repeat weighing by touching