NE1xx series Unstirred Baths User Manual Issue 15 Nov 2006

Contents About this Manual General Notes Amendments Symbols

3 3 3 3

Location Unpacking Safety Assembly Power Supply Lead and Connection to Electrical Supply Liquid Level Suitable Liquids

4 4 4 4 4 4 4

NE1B Series Product Overview

5

NE1 Series Product Overview

6

Operating Instructions NE1B Series Operating Instructions NE1 Series

7 7

Explanation of Temperature Control Terms

8

General Cleaning Cleaning external painted surfaces with Anti-bacterial finish Cleaning the stainless steel tank

9 9 9

Descaling the stainless steel tank Decontamination of equipment Virucidal Disinfectant Disinfectant/Sterilant

10 10 10 10

3 Year Warranty Out of Warranty End of Life Portable Appliance Testing

11 11 11 11

Accessories

12

Fitting Accessories

13

Service and Parts List

14

Specification NE1B Series

15

Specification NE1 Series

16

Specification NE1 Shallow Form

17

Declaration of Conformity

18

Final Inspection and Electrical Safety Test Report

Enclosed Rear

The Clifton Range - 3 Year Warranty

2

High Quality Products at Affordable Prices

PDF created with pdfFactory Pro trial version www.software-partners.co.uk

About this Manual This user Manual contains instructions which must be followed in order that the product is operated correctly. General Notes Please observe the following safety precautions: 1. Fill the tank prior to connection to power supply. 2. Connect only to a power supply with the corresponding voltage to that specified on the rating label positioned on the rear of the unit. 3. Ensure the power supply has a safety earth (ground) terminal. 4. Ensure the mains switch and power supply connector are accessible during use. 5. The mains supply cord fitted to these products is a heat resistant type and should be replaced by an equivalent type. 6. Do not block ventilation slots during use and follow installation instructions. 7. Always follow good laboratory practice by ensuring substances being heated present no risk of a hazard (explosion, implosion or release of toxic or flammable gases) or that these have been addressed. When heating substances where liberation of gases occurs suitable extraction should be used. 8. Use only liquids specified in this Instruction Manual within their specified temperature range. 9. Use caution when topping up or draining the tank as the liquid in the tank may be very hot or cold. Allow the liquid to cool to 40°C before draining. 10. Drain before moving the bath. 11. Recommend using a Lid above 60°C. Take care when lifting the lid - steam and hot vapours can cause scalding. 12. Use a thermometer to check the temperature - do not touch liquid. 13. If this product is not used in accordance with these instructions, then basic safety protection afforded by the water bath may be affected. 14. Before using any cleaning or decontamination method except those recommended, check with your distributor that the proposed method will not damage the equipment. Amendments Issue 1 July 1991 Initial issue instruction book. Issue 2 February 1993 Revised added NE1-28 version. Issue 3 June 1993 NE1B range introduced. Issue 4 August 1994 Instruction book revised layout. Issue 5 May 1995 CE version. Issue 6 September 1995 Multi-lingual version. Issue 7 May 1996 Update address details. Issue 8 November 1997 NE1-22/28, NE1B-14 fuse revision. Issue 9 September 1999 F to T. Issue 10 July 2000 Complete update. Issue 11 July 2001 Product updates for 2002. Issue 12 September 2004 Revised instruction book. Issue 13 July 2005 New NE1-9, NE1B range updated constant level and MCB’s. Issue 14 July 2006 NE1B-14 1000W to 1200W and Note front cover filling bath. Issue 15 November 2006 Improved disinfection/sterilisation notes, explanation of accuracy, sensitivity etc, Anti-bacterial paint finish. Symbols HOT SURFACES Paragraphs marked by this symbol indicate that a potential hazard to your personal safety exists from heated surfaces or other appendages on the outside or inside of the equipment. CAUTION This icon accompanies text and/or other international symbols dealing with potential damage to equipment. When present, it indicates that there is a potential danger of equipment damage may occur if information stated within the "CAUTION" paragraph is not adhered to or procedures are executed incorrectly. PROTECTIVE EARTH OR GROUND TERMINAL Protective earth conductor terminal. The Clifton Range - 3 Year Warranty

3

High Quality Products at Affordable Prices

PDF created with pdfFactory Pro trial version www.software-partners.co.uk

Location The surface on which the product is to be located should be smooth, level and sturdy. Use in a ventilated room. Product is designed for laboratory use. Unpacking Remove the product from its packaging. Any damage to the product notify your distributor immediately. Retain packaging over warranty period. Contents consist of a bath, stainless steel false base, power lead and instruction manual. Safety Do not touch any electrical contacts or open any closure panels RISK OF ELECTRICAL SHOCK! Assembly Place the false base inside the bath. Fit the power lead into the socket at rear. Power Supply Before attempting to connect the product to an electrical supply check the information on the rating label is compatible. IF IN DOUBT CONSULT AN ELECTRICIAN. THE PRODUCT MUST BE EARTHED!. Where the mains supply or plug differs refer to local regulations or qualified electrician. Liquid Level - NE1 range Minimum liquid level - must cover the top of the false base by 40mm Maximum liquid level - must not exceed the ridge in the tank. Always ensure the product is disconnected from the electrical supply when emptying and filling. Suitable Liquids - NE1 range Operating temperatures from ambient +5°C to 99°C, for general use we recommend either: - Distilled water. - Heat transfer liquid [The LB range is formulated for temperatures from -45°C to 90°C and provides complete protection from freezing and algae growth and safeguards against corrosion. See accessories for the full range available]. - VIRKON dissolved in distilled water has proven efficacy against bacteria (including mycobacteria), viruses, spores and fungi in a variety of independent tests using different protocols. Liquid Level - NE1B range Minimum and maximum water level is governed by the constant level which maintains water level during boiling. Using standard laboratory tubing, connect to the bottom outlet of the constant level to a regulated water supply/tap, adjust the water supply to provide a slow feed of water and maintaining boiling and this automatically maintains safe water level. The side outlet acts as an overflow to a sink or drain. Suitable Liquids - NE1B range Normal tap water is suitable since a maintained water supply is required. The Clifton Range - 3 Year Warranty

4

High Quality Products at Affordable Prices

PDF created with pdfFactory Pro trial version www.software-partners.co.uk

NE1B Series Product Over View

Clifton “Low” height shelf needs less water for same work saving energy and costs. Also allows tall samples to be immersed to either a greater working depth.

Front View

Dial: adjusts level of boiling. Indicator: heating.

Splash proof controls.

Mains power switch “I” ON, “O” OFF. Drain outlet for accessory tap: 28 litre model. Rear Views Serial number and electrical supply details. Power supply lead and plug.

MCB fuses Normal use requires no action. Fault situation, buttons will pop out disconnecting electrical supply. SEEK GUIDANCE before resetting push to reset .

Constant level device, maintains liquid level during boiling. Outlet, connect with laboratory tubing to a drain or waste outlet. Inlet, connect with laboratory tubing to fill the Boiling bath then adjust the flow water supply, to maintain liquid level

The Clifton Range - 3 Year Warranty

5

High Quality Products at Affordable Prices

PDF created with pdfFactory Pro trial version www.software-partners.co.uk

NE1 Series Product Over View

Clifton “Low” height shelf needs less water for same work saving energy and costs. Also allows tall samples to be immersed to either a greater working depth.

Front View

Dial, thermostatic control, set to desired temperature. Indicator: heating.

Splash proof controls. Mains power switch “I” ON, “O” OFF. Drain outlet for accessory tap: 22, 28 and 56 litre models. Rear View Serial number and electrical supply details. IEC connector, for power supply lead and plug. Fuse draw fitted underneath.

The Clifton Range - 3 Year Warranty

6

High Quality Products at Affordable Prices

PDF created with pdfFactory Pro trial version www.software-partners.co.uk

NE1B Series: Operating Instructions 1. Fill the bath with water following instructions on Page 4 Liquid Level - NE1B range and diagram on Page 5. 2. Connect the mains plug to an electrical supply. 3. Turn unit on using mains switch located on the front of the unit.

4. Heater indicator will illuminate to show heater activity.

5. Adjust the blue knob to control the degree of boil from gentle simmer to vigorous boil. 6. Allow the water temperature to stabilise in the bath, and take an actual temperature reading. NE1 Series: Operating Instructions 1. Fill the bath with water observing recommended levels on Page 4 Liquid Level - NE1 range

2. Connect the mains plug to an electrical supply.

3. Turn unit on using mains switch located on the front of the unit.

4. Adjust the temperature control to the desired setting using the blue knob.

5. Heater indicator will illuminate to show heater activity.

6. Allow the water temperature to stabilise in the bath, and take an actual temperature reading. Adjust the temperature controller accordingly.

The Clifton Range - 3 Year Warranty

7

High Quality Products at Affordable Prices

PDF created with pdfFactory Pro trial version www.software-partners.co.uk

Explanation of Temperature Control Terms Accuracy We do not provide, claim or assure any form of accuracy. Accuracy is defined as "the ability of a measurement to match the actual value of the quantity being measured". For accuracy we recommend using a calibrated reference probe at the actual set point temperature and where necessary, adjust the set point accordingly. Sensitivity For an explanation of sensitivity consider a unstirred digital water bath, the PID temperature control system measures and displays the actual temperature of the water and then compares it with the ‘set point’ temperature. It automatically calculates and adjusts the required quantity of heat into the bath to make the measured temperature equal to the set temperature. As with any process there is a time delay between measuring the temperature and the heat entering the water, which causes minor fluctuations in the temperature of the bath. Heat is also distributed in an unstirred bath by convection and conduction and there are heat losses from the surface of the liquid which can cause temperature losses. These losses and heat distribution produce small fluctuations in temperature across the water in the bath. These small temperature fluctuations at any one point are defined as “sensitivity” and vary between an upper and lower limit, however occasionally a larger variation can be observed. Sensitivity as stated in DIN 58966 is the temperature difference between the upper and lower temperature level over 100 cycles after removing the largest 25% of readings. We determine sensitivity by recording the actual upper and lower temperatures of the bath using temperature loggers and is stated as plus or minus one half of the measured value. Uniformity Uniformity is calculated by measuring the temperature in opposing ends of the water bath and is the difference between the mean temperatures at these two points and stated as plus or minus half this value.

The Clifton Range - 3 Year Warranty

8

High Quality Products at Affordable Prices

PDF created with pdfFactory Pro trial version www.software-partners.co.uk

Cleaning General Important - please follow these instructions to avoid possible damage to the unit, otherwise affecting its performance and warranty. Always disconnect the product from the electrical supply before cleaning. Cleaning External Painted Surfaces featuring “Anti-bacterial Paint Finish” The water bath should be cleaned at regular intervals wiping external surfaces with a cloth or sponge soaked in warm soapy water with a mild detergent. All surfaces should be cleaned using a soft cloth or sponge. Do not under any circumstances use strong solvents or solutions containi ng Chlorinated Hydocarbons, Esters, Ketones or abrasive cleaners or polish on the paint finish otherwise it damages the built in anti-bacterial properties. All painted surfaces on Clifton range products features an “Anti-bacterial paint finish” identified with this authenticating logo on the unit. This “Anti-bacterial paint finish” inhibits the growth of bacteria. It has been tested by independent specialist test houses such as the Law Laboratories (in the UK) using internationally recognized test methods and proven to be effective versus a wide range of bacteria species including Escherichia coli and Staphylococcus aureus (MRSA). We recognise hygienic coatings are part of a controlled approach to a cleaner working environment. Within its formulation an active ingredient with proven anti-bacterial properties is bound into the paint finish. The efficacy of the paint finish applied to the Clifton range is maintained over its lifetime, as the anti-bacterial agent is integral within the paint. In a laboratory environment it makes this one less source of contamination, contributing to essential clean working practices. A benefit of such a paint finish can lead to a reduction in cleaning schedules because surfaces are more protected and improves protection between cleaning. Unlike detergents “Anti-bacterial paint finish” does not offer an instantaneous action, but is intended for long-term general protection against bacterial growth. Moisture on the painted surface is necessary for the bacterium to absorb the agent and be affected by it. The coating is therefore less active in very dry conditions, but dependent upon relative humidity, moisture in the atmosphere maintains activity. Areas where moisture is trapped are also areas that normally are difficult to clean and where bacteria proliferate but these areas are most active for the anti-bacterial coating improving the defence against bacterial growth. Cleaning the Stainless Steel Tank The stainless steel crevice free tank with smooth corners should provide years of valuable service and is resistant to chloride containing solutions it is however important to avoid high concentrations of halogens - especially chloride. With such a high quality and resistant tank it may show symptoms of these halogens as rust, which are deposits from external sources in the water supply. We recommend always empty the bath of liquid after use and wipe out the internal faces of the tank with a non-abrasive cloth and allow to dry. Any deposits can be removed with nitric acid (10%) on a cloth. WEAR PROTECTIVE EQUIPMENT! It is also recommended to use an accessory lid to prevent contaminates landing in bath liquids. The Clifton Range - 3 Year Warranty

9

High Quality Products at Affordable Prices

PDF created with pdfFactory Pro trial version www.software-partners.co.uk

Descaling the Stainless Steel Tank Descale the stainless steel tank regularly to maintain it in as new condition ensuring the corrosion resistance and normal operating conditions are maintained throughout its working life. Descale by adding 1 litre of vinegar to water and gently heating to 50°C for an hour, empty and brush the lime away. Rinse thoroughly afterwards. Decontamination of Equipment Clifton laboratory equipment can be decontaminated after spillage or contact with potentially HIV and Hepatitis infected blood samples during analysis using following recommended rapid disinfectants. Virucidal Disinfectant We recommend Virkon tablets for the safe and rapid disinfection of equipment in a wide variety of situations available from your distributor or contact Day-Impex Ltd. for more details. Telephone: 44+(0)1787 223232 or http://www.day-impex.co.uk The ultimate high level surface disinfectant, dissolve VIRKON in water, providing a safe working solution with a faint lemon odor. It has proven efficacy against bacteria (including mycobacteria), viruses, spores and fungi in a variety of independent tests using different protocols. Presents no serious long term health risks to staff – obviating the need for costly ventilation equipment and health monitoring. Also provides high level disinfection of laboratory equipment and instruments where autoclaving is neither practical nor necessary. For more detailed information relating to how Virkon should be used with access to test reports www.relyon.dupont.com Is Virkon solution corrosive? Virkon solution requires only 10 minutes contact time to be effective so long-term exposure is not necessary and therefore will not corrode most materials. Care should be taken with Stainless steel water bath tanks, these surfaces should not be affected however, it is important that generally you do not leave Virkon solution in contactwith metal surfaces “FOR LONGER THAN IS NECESSARY”. Virkon is Registered in accordance with the requirements of the Medical Devices Directive, (93/42/ EEC) as a Medical Device. Disinfectant/Sterilant We recommend PeraSafe a powder product for the safe and rapid chemical sterilant of equipment in a wide variety of situations available from your distributor or contact Day-Impex Ltd for more details. Telephone: 44+(0)1787 223232 or http://www.day-impex.co.uk PeraSafe has a proven safety profile for end-users with none of the undesirable properties of skin sensitisation, toxic fumes or unpleasant odours that are associated with aldehyde solutions. Leading UK and USA microbologists have proven PeraSafe to be active against viruses, mycobacteria and fungi. It is microbiologically superior to glutaraldehyde, destroying sporing bacteria in one minute. It has also been independently proven that PeraSafe sterilises in just 10 minutes. For more detailed information relating to how PeraSafe should be used with access to test reports www.relyon.dupont.com

The Clifton Range - 3 Year Warranty

10

High Quality Products at Affordable Prices

PDF created with pdfFactory Pro trial version www.software-partners.co.uk

3 Year Warranty Our service engineers are fully trained in the assembly, calibration and servicing of all Clifton instrumentation. Products can be returned to our comprehensively equipped service centre where a fast and efficient turnaround is guaranteed: Service Department, Nickel Electro Limited, Oldmixon Crescent, Weston-super-Mare, North Somerset BS24 9BL, UK. Tel +44 (0)1934 626691 Fax +44 (0)1934 630300. Out of Warranty Our Service Department has a comprehensive stock of charegeable spare parts maintaining working life of equipment or units can be returned for quotation before repairs are undertaken. End of Life This symbol indicates that this product should not be disposed of with your waste. Instead, dispose waste electrical equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling: UK please contact Service Department, rest Europe contact your Distributor. Health & Safety, unless in receipt of a Decontamination Notice or Report the unit cannot be returned or accepted for disposal. Clifton electrical and electronic equipment has been designed for recycling and takes into account the dismantling and recovery its components and materials. Clifton products are easily recycled with majority of the product constructed from stainless or mild steels, which can readily be re-used or recycled. In excess of 86% of this product range can be easily re-cycled economically. Portable Appliance Testing When conducting testing, ensure it is conducted by a qualified person. DO NOT PAT TEST THE BATH UNLESS IT CONTAINS WATER. THIS EQUIPMENT MUST NOT BE FLASH TESTED!

The Clifton Range - 3 Year Warranty

11

High Quality Products at Affordable Prices

PDF created with pdfFactory Pro trial version www.software-partners.co.uk

Accessories for NE1 and NE1B Series GRP Gable Lids GL1-4 GL1-14 GL1-22

GRP Gable Lid to suit 4 Litre Unstirred Baths GRP Gable Lid to suit 14 Litre Unstirred Baths GRP Gable Lid to suit 9, 22 and 28 Litre Unstirred Baths

Stainless Steel Gable Lids SL1-4 SL1-8 SL1-14 SL1-22 SL1-22H

Stainless Steel Gable Lid to suit 4 Litre Unstirred Baths Stainless Steel Gable Lid to suit 8 Litre Unstirred Baths Stainless Steel Gable Lid to suit 14 Litre Unstirred Baths Stainless Steel Gable Lid to suit 9, 22 and 28 Litre Unstirred Baths Stainless Steel Hinged Gable Lid to suit 22 + 28 Litre Unstirred Baths

Stainless Steel Flat Lids LD-4 LD-8 LD-14 LD-22 SA01368

Flat One Piece Stainless Steel Lid to suit 4 Litre Capacity Bath Flat One Piece Stainless Steel Lid to suit 8 Litre Capacity Bath Flat One Piece Stainless Steel Lid to suit 14 Litre Capacity Bath Flat One Piece Stainless Steel Lid to suit 9, 22 & 28 Litre Capacity Bath Flat One Piece Stainless Steel Lid to suit 56 litre bath (two required)

Stainless Steel Flat Lids with Concentric Rings SLR1-4 SLR1-8 SLR1-14 SLR2-14 SLR1-22

4 x 105mm Stainless Steel Ringed Lid to suit 4 Litre Unstirred Baths 4 x 83mm Stainless Steel Ringed Lid to suit 8 Litre Unstirred Baths 4 x 105mm Stainless Steel Ringed Lid to suit 14 Litre Unstirred Baths 6 x 83mm Stainless Steel Ringed Lid to suit 14 Litre Unstirred Baths 6 x 105mm Stainless Steel Ringed Lid to suit 9, 22 and 28 Litre Unstirred Baths

Stainless Steel Test Tube Racks - Dimensions 270 x 70 x 138mm (L x W x H) 6870 6871 6872 6873 6900

Stainless Steel Test Tube Rack 26 Hole x 17mm Diameter Stainless Steel Test Tube Rack 16 Holes x 26mm Diameter Stainless Steel Test Tube Rack 36 Holes x 13mm Diameter Stainless Steel Test Tube Rack 18 Holes x 19mm Diameter/suitable for 1.5ml microtubes Stainless Steel Test Tube Rack 12 Holes x 32mm Diameter Note: 4 Litre = 1 Rack, 8 Litre = 2 Racks, 14 Litre = 4 Racks, 22 and 28 Litre = 6 Racks

Miscellaneous LB-2.5 LB-5.0 TC-1 BX0616 BX0688 BP0368

2.5 Litres - Lab Bath 4590 - Heat transfer fluid - Temperature range -15° to +90°C 5 Litres - Lab Bath 4590 - Heat transfer fluid - Temperature range -15° to +90°C Thermometer Clip Complete With Bent Stem Spirit Filled Thermometer Draining Syphon Drain Tap Polypropylene Spheres

For more information on Accessories visit www.nickel-electro.co.uk

The Clifton Range - 3 Year Warranty

12

High Quality Products at Affordable Prices

PDF created with pdfFactory Pro trial version www.software-partners.co.uk

Fitting Accessories for NE1 and NE1 Series GRP Gable Lids Position the lid over the bath and lower into place. The lids are designed to fit snugly so that condensate runs into the bath. Stainless Steel Gable Lids Position the lid over the bath and lower into place. These lids have bo drip points, provide full working height across the bath when fitted and have a ventilation gap. For “H” suffix lids place the lid onto the bath with the hinges hanging over the rear of the water bath aliigning with threaded bushes. Insert two screws provided into each hinge and tighten screws. The lid can be raised and lowered using the handle on the side. Stainless Steel Flat Lids Position the lid over the bath and lower into place. Stainless Steel Flat Lids with Concentric Rings Position the lid over the bath and lower into place. Each set of rings can be used to vary the diameter of aperture to accommodate different sizes of vessels of evaporating dishes and glassware, including round-bottom flasks. Stainless Steel Test Tube Racks Place the loaded test tube rack into the bath on top of either the stainless steel perforated shelf or the raised shelf. Note: 4 Litre = 1 Rack, 8 Litre = 2 Racks, 14 Litre = 4 Racks, 22 and 28 Litre = 6 Racks Heat Transfer Fluid Use as a ‘neat’ liquid solution for best results. Thermometer Clip This can be positioned anywhere on the perimeter of the bath by cliping over the edge. The thermometer then lies flush with the top edge of the bath to prevent accidental damage. Draining Syphon Allows the easy and quick emptying of any water bath. Water temperature must be below 45°C before emptying can commence. Drain Tap A drain tap outlet is featured on the 22, 28 and 56 litre sizes. Make sure the bath is empty, hold the outer nut, then using a socket/allen key undo the threaded insert. Once removed and still holding the outer nut, screw in the accessory drain tap into position and pinch tight. Polypropylene Spheres Place on top of the water/oil to provide a floating lid reducing evaporation and insulating the bath reducing heat losses. The range of Unstirred water baths: 4 litre bath requires 1 pack; 8 litre bath requires 2 pack; 14 litre 2 packs and 9, 22 and 28 litre requires 4 packs.

The Clifton Range - 3 Year Warranty

13

High Quality Products at Affordable Prices

PDF created with pdfFactory Pro trial version www.software-partners.co.uk

Service Diagrams and Spare Parts - NE1

Service Diagrams and Spare Parts - NE1B

The Clifton Range - 3 Year Warranty

14

High Quality Products at Affordable Prices

PDF created with pdfFactory Pro trial version www.software-partners.co.uk

NE1B range Clifton Boiling Baths, water, unstirred Designed for applications that require continuous boiling. This range also has the flexibility to allow the temperature to be regulated from a gentle simmer to a vigorous boil. Comprising of a corrosion resistant stainless steel working environment, with heater and safety cut out concealed underneath providing a totally clear ‘clutter free’ working area, all housed in a durable, chemical resistant, powder coated paint finished outer case. Integral constant level device for connection to water supply to combat evaporation of water and maintain boiling. Featuring Clifton “Low” height removable stainless steel shelf increasing working volume. Drain outlet on 28 litre model for convenient bath emptying Heating element with safety cut-out concealed underneath the bath

Cat No.

NE1B-8

NE1B-14

NE1B-28

Capacity, litres

8

14

28

Heater power, W

800

1200

1500

Drain Outlet

No

No

Yes

Safety

Fixed cut out

Fixed cut out

Fixed cut out

Internal Dims, mm (wxdxh)

240x300x150

325x300x150

500x300x200

Overall Dims, mm (wxdxh)

332x270x290

361x332x290

538x332x290

Voltage

230V or 120V

The Clifton Range - 3 Year Warranty

15

High Quality Products at Affordable Prices

PDF created with pdfFactory Pro trial version www.software-partners.co.uk

NE1 range Clifton Baths, water, thermostatic, unstirred A broad range of unstirred analogue baths designed for general use and economically priced without comprising quality. Comprising of a corrosion resistant stainless steel working environment using a 304 spec (18/8) stainless steel tank with heater and safety cut out concealed underneath providing a totally clear ‘clutter free’ working area, all housed in a durable, chemical resistant, powder coated paint finished outer case. Easy to use thermostatic control, graduated in 5°C increments, with illuminated on/off switch and “heater on” indicator. Featuring removable unique Clifton “Low” height removable stainless steel shelf, water saving feature and reducing energy consumption or increasing working volume. Side lifting handles for ease of transportation. Drain outlet on larger volumes 22, 28 and 56 litre models for safe and convenient bath emptying. Temperature factory calibrated @ 45°C for consistency. Complementary range of accessories including racks and lids.

Cat No.

NE1-2.5

NE1-4

NE1-8

NE1-14

NE1-22

NE1-28

NE1-56

Capacity, L

2.5

4

8

14

22

28

56

Temperature

Ambient +5°C - 100°C

Sensitivity

±0.25°C

Uniformity

±0.1°C

Heater, W

250

400

800

1000

1500

1500

2500

Drain Outlet

No

No

No

No

Yes

Yes

Yes

Internal, mm

230x130x100

300x150x150

300x240x150

325x300x150

500x300x150

500x300x200

620x500x200

Overall, mm

270x190x240

332x185x290

332x270x290

361x332x290

538x332x290 538x332x290

660x540x290

Voltage

The Clifton Range - 3 Year Warranty

230V or 120V

16

High Quality Products at Affordable Prices

PDF created with pdfFactory Pro trial version www.software-partners.co.uk

NE1 range Clifton Baths, shallow form, water, thermostatic, unstirred A shallow height unstirred water bath designed for operating with low liquid levels suitable for small bottles, tubes and micro plates. Perfect for heating samples in Microcentrifuge tubes and molecular biology Low profile design allowing easy access and visibility of work in the bath Unlike traditional high sided baths, small containers and samples are not obscured

Cat No.

NE1-9

Capacity, litres

9

Temperature range

Ambient +5°C - 100°C

Sensitivity

±0.25°C

Uniformity

±0.1°C

Heater power, W

1000

Drain Outlet

No

Internal Dims, mm (wxdxh)

500x300x65

Overall Dims, mm (wxdxh)

535x332x135

Voltage

230V or 120V

The Clifton Range - 3 Year Warranty

17

High Quality Products at Affordable Prices

PDF created with pdfFactory Pro trial version www.software-partners.co.uk

EC Declaration of Conformity We herewith confirm the following product: NE1B and NE1 Series of Unstirred WaterBaths Conform with the requirements outlined by the following European Directives: Low Voltage Directive (73/23/EEC) EMC Directive (89/336/EEC) We confirm the declaration

NICKEL-ELECTRO Ltd. Manufacturers of laboratory, medical and clinical equipment. Oldmixon Crescent, Weston-super-Mare, North Somerset, BS24 9BL, United Kingdom. Tel: +44 (0)1934 626691 Fax: +44 (0)1934 630300

Email: [email protected] www.nickel-electro.co.uk Conforms with the requirements of following standards: BS EN 61010:1 BS EN 61010:2.010 Safety requirements for electrical equipment for measurement, control and laboratory use. BS EN 61326 Electrical equipment for measurement control and laboratory use - EMC requirements.

Nickel-Electro Ltd, Oldmixon Crescent, Weston-s-Mare, North Somerset, BS24 9BL, England t 01934 626691 f 01934 630300

The Clifton Range - 3 Year Warranty

18

High Quality Products at Affordable Prices

PDF created with pdfFactory Pro trial version www.software-partners.co.uk

Final Inspection and Electrical Safety Test Report

2BX0842

www.nickel-electro.co.uk

PDF created with pdfFactory Pro trial version www.software-partners.co.uk