DP6600 Operation Manual Advanced Ver 1.2

© 2005-2006 Shenzhen Mindray Bio-medical Electronics Co., Ltd. All rights Reserved.

Product Information: Product Name: Digital Ultrasonic Diagnostic Imaging System Model: DP-6600 Issued Date of this manual: 2006-05 Manual Version: 1.2

Intellectual Property Statement SHENZHEN MINDRAY BIO-MEDICAL ELECTRONICS CO., LTD. (hereinafter called Mindray) owns the intellectual property rights to this Mindray product and this manual. This manual may refer to information protected by copyrights or patents and does not convey any license under the patent rights of Mindray, nor the rights of others. Mindray does not assume any liability arising out of any infringements of patents or other rights of third parties. Mindray intends to maintain the contents of this manual as confidential information. Disclosure of the information in this manual in any manner without the written permission of Mindray is strictly forbidden. Release, amendment, reproduction, distribution, rent, adaptation and translation of this manual in any manner whatsoever without the written permission of Mindray is strictly forbidden.

IMPORTANT! 1. 2.

No part of this manual may be copied or reprinted, in whole or in part, without written permission. The contents of this manual are subject to change without prior notice and without our legal obligation.

I-1

Introduction This operation manual describes operating procedures for DP-6600 Digital Ultrasonic Diagnostic Imaging system. To ensure safe and correct operation of the system, carefully read and understand the manual before operating the system. NOTE:

For certain applications, the following manual is available:

• Basic Volume

Depending on the software version, the actual interface may appear different from those shown in this manual.

I-2

Safety Precautions 1. Meaning of Signal Words

In this operation manual, the signal words

DANGER,

WARNING,

CAUTION and NOTE are used regarding safety and other important instructions. The signal words and their meanings are defined as follows. Please understand their meanings clearly before reading this manual. Signal word

Meaning

DANGER

Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION

Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

NOTE

Indicates a potentially hazardous situation which, if not avoided, may result in property damage.

2. Meaning of Safety Symbols Symbol

Description Type-BF applied part NOTE :All ultrasound transducers can be connected to this system are Type-BF applied part. "Attention" indicates the points requiring attention. Be sure to read the operation manual concerning these points before using the equipment.

S-1

3. Safety Precautions Please observe the following precautions to ensure patient and operator safety when using this system.

CAUTION: 1. Display the most suitable image and select the most suitable measurement mode for the intended measurement. The results must be determined by a specialist. 2. The basic measurement results are not displayed in the exam report. 3. Be sure to perform measurement within images. If the area is outside the image, incorrect diagnosis may result. 4. The detailed precautions for each measurement are described in the

corresponding

section.

Read

and

understand

these

precautions before performing the measurement. 5. Data in temporary storage areas, such as the CINE memory, is deleted when the power supply is turned OFF or when the Patient switch is pressed. Such data may also occasionally be deleted due to accidents. To minimize the possibility of reexamination being required as a result of unintended data deletion, back up the required images on external storage media. 6. Refer to the Operation Manual (Basic Volume) for precautions regarding the use of this system.

S-2

Contents

1

Preset ...1-1 1.1

Access/Exit Preset Mode ... 1-1

1.2

Display/Modify Preset Information ... 1-2

1.3

General preset ... 1-3

1.4

Preset Parameters of Exam Mode... 1-4

1.5

Preset Formula ... 1-9

1.6

Preset Post Process Curve and Parameter ... 1-12

1.6.1 Gray Transformation Curve... 1-13 1.6.2 Gray rejection curve... 1-13 1.6.3 γ correction ... 1-14 1.7

Preset comment... 1-15

1.7.1 Adding Comment ... 1-15 1.7.2 Deleting Comment ... 1-16 1.8

Save/Load Preset Data... 1-16

1.8.1 Save Preset Data... 1-16 1.8.2 Load DTA file ... 1-18 1.8.3 Factory Data ... 1-18 1.9

Maintenance ... 1-19

1.10 Preset DICOM (Optional accessory)... 1-19

2

3

Basic Operation of Measurements & Calculations ...2-1 2.1

Select the Exam Mode... 2-1

2.2

Accessing Measurement Status... 2-1

2.3

Measurement Menu ... 2-1

2.4

Measured Result and Help Information... 2-3

2.5

Keys Used during Measurement... 2-4

2.6

Classification of Measurements and Calculations... 2-5

2.7

Attention... 2-6

B mode General Measurements & Calculations...3-1 3.1

Distance... 3-2

3.2

Circumference and Area ... 3-2

3.3

Volume... 3-4 C-1

3.4

Ratio ... 3-5

3.5

Stenosis Ratio... 3-6

3.6

Angle... 3-7

3.7

Histogram ... 3-7

3.8

Profile... 3-9

3.9

Other Measurements ... 3-10

3.10 Print General Report ... 3-10

4

5

M Mode General Measurements & Calculations...4-1 4.1

Distance... 4-1

4.2

Time... 4-2

4.3

Slope... 4-2

4.4

Heart Rate ... 4-3

Obstetric Measurements & Calculations ...5-1 5.1

Abbreviations used ... 5-2

5.2

Measurement items ... 5-2

5.3

Fetal Growth Measurements... 5-3

5.3.1 GS ... 5-3 5.3.2 CRL ... 5-4 5.3.3 BPD ... 5-4 5.3.4 HC ... 5-5 5.3.5 AC ... 5-5 5.3.6 FL ... 5-5 5.3.7 AFI ... 5-6 5.3.8 TAD... 5-6 5.3.9 APAD ... 5-7 5.3.10 CER ... 5-7 5.3.11 FTA ... 5-7 5.3.12 HUM... 5-8 5.3.13 OFD ... 5-8 5.3.14 THD ... 5-8 5.4

EDD ... 5-9

5.4.1 Calculating the EDD according to LMP... 5-9 5.4.2 Calculating the EDD according to BBT ... 5-9 5.5

EFW... 5-10

5.5.1 Formulae... 5-10

C-2

5.5.2 Measurement items ... 5-11 5.5.3 Sample... 5-11 5.6

Results... 5-12

5.6.1 Growth Curves Comparison... 5-12 5.6.2 Fetal Biophysical Profile... 5-13 5.6.3 FBP Report ... 5-16 5.6.4 Obstetric Exam Report... 5-17 5.6.5 Printing Obstetric Report... 5-18

6

5.7

Others ... 5-19

5.8

References ... 5-20

Cardiac Measurements & Calculations ...6-1 6.1

Key in items ... 6-1

6.1.1 Entering HR ... 6-1 6.1.2 Entering LVET... 6-1 6.1.3 Entering H & W ... 6-2 6.2

M Mode Measurements ... 6-3

6.2.1 LV... 6-8 6.2.2 SV, EF, FS... 6-8 6.2.3 CO ... 6-9 6.2.4 MVCF... 6-9 6.2.5 CI, SI... 6-10 6.2.6 Measuring all parameters of LV simultaneous ... 6-10 6.2.7 LVMW and LVMWI... 6-11 6.2.8 Mitral measurement ... 6-11 6.2.9 Aorta measurement... 6-12 6.3

B Mode Measurements... 6-13

6.3.1 LV measurement using Single Plane Ellipse method... 6-18 6.3.2 Others measurement method for LV ... 6-18 6.3.3 CO ... 6-18 6.3.4 CI, SI... 6-19 6.3.5 RV... 6-19 6.3.6 Other Parameters ... 6-19 6.4

7

Cardiac Exam Report ... 6-20

Gynecology Measurements & Calculations...7-1 7.1

UT (Uterine body) ... 7-3

C-3

7.2

Endo (Endometrium)... 7-3

7.3

OV-V (Ovary Volume) ... 7-3

7.3.1 L.OV-V ... 7-3 7.3.2 R.OV-V... 7-4 7.4

FO-D (Dominant Follicle) ... 7-4

7.4.1 L.FO... 7-4 7.4.2 R.FO ... 7-5

8

7.5

CX-L (Uterine Cervix Length)... 7-5

7.6

UT-L/CX-L (Uterine body / cervix) ... 7-5

7.7

Others ... 7-5

7.8

Gynecology Exam Report ... 7-6

Small parts Measurements & Calculations ...8-1 8.1

THY (Thyroid) ... 8-2

8.1.1 L.THY-V ... 8-2 8.1.2 R.THY-V... 8-3

9

8.2

THY RPT ... 8-3

8.3

Others ... 8-4

Urology Measurements & Calculations...9-1 9.1

RUV ... 9-2

9.2

Prostate Volume ... 9-2

9.3

Urology Exam Report ... 9-3

9.4

Others ... 9-3

10 Orthopedics Measurements & Calculations ...10-1 10.1 HIP... 10-1 10.2 HIP RPT... 10-2 10.3 Others ... 10-3

C-4

1

Preset

Preset function is used to set the system operating environment, status and the configuration parameters for each exam mode. The preset values are saved in the memory inside the system, which will not be lost if power-off occurs so as to ensure that the system operates in the user-desired status automatically after each start-up. This chapter gives detailed description about how to make system configuration through using the preset menu in Preset mode.

1.1 Access/Exit Preset Mode Access the preset mode: Press the 『File』 key on the control panel. The 『File』 lamp lights up. The FILE MENU appears on the right part of the screen. See figure below. Then select the preset item and press 『Set』 key. The system accesses the preset mode. Select the item in the PRESET menu to preset the corresponding parameters.

1-1

Preset

Exit Preset mode: In Preset mode, move the cursor to the [Return] item of the menu and press the 『Set』 key to close the PRESET menu. The system exits the preset mode and begins running according the modified parameters.

1.2 Display/Modify Preset Information To set up all the preset parameters and curves, the user should select the item in the PRESET menu to call up the preset dialog box. The general outline of the preset dialog box is as shown in figure as following. Dialog Title Item Page 1

Page 2

Page 3

page button

Content of dialog

Record Current

Cancel

Ok

command button

Help

Procedures to modify the preset parameters or curves: 1.

Move the cursor to select the corresponding item in the PRESET menu and press the 『Set』 key to call up the corresponding preset dialog box.

2.

If a dialog box having more than one page, first move the cursor to select the button of the desired page so as to open the corresponding preset page.

3.

Move the cursor to the bar of the parameter to be adjusted and use the 『Set』 or the 『Back』 key to adjust the parameter. At this time, the operating information is displayed in the Help bar.

4.

After setting the information in the current page, select the button of another page to set other parameters. After all the parameters have been set up, press the 『Set』 key on the 「Ok」 button to make these settings come into effect and be saved in the system, and at the same time to close the dialog box.

5.

To cancel the modifications, just press the 『Set』 key on the 「Cancel」 button. This action at the same time closes the dialog box.

6.

Move the cursor to the [Return] item of the PRESET menu and press the 『Set』 key to close the PRESET menu. 1-2

Preset

There are also some special buttons in the preset dialog box, whose functions are: z

「Record Current」

Besides setting the parameters in the current page one by one, the user can also use the “record the current value” method to preset parameters. Press the『Set』 key on the「Record Current」 to set each parameter (curve) as the value (parameter or curve) used by the system before accessing the preset mode. That is to say to set up the current operating parameters of the system as the preset parameters.

NOTE: 「Record Current」 buttons are only valid in the current page.

1.3 General preset Move the cursor to select the [General] item in the menu to call up the [General Preset] dialog box. See figure below.

The table below is the description of the preset items in the dialog box.

1-3

Preset

Item

Selections

Functional Description

Hospital

Entered by the user

To enter the hospital name displayed on the top left corner of the screen and in the diagnosis report.

Default Exam

Abd / Gyn / Car/Ob / Sml

To select the exam mode.

Language

English

To select the language used by the system, only English can be set..

Post-P Menu

√/ ×

To show/hide the Post-P submenu.

Video Mode

NTSC/PAL

Set the mode of image

Print Image

√/ ×

To select print image or not.

Date format

YYYY/MM/DD MM/DD/YYYY DD/MM/YYYY

Date

Adjusted by the user

or or

Set date format of the system To enter the system date; Format: year/month/day Year range: 2000-2099.

Time

Adjusted by the user

To enter the system time; Format: hour/minute/second

Screen Saver

√/ ×

Set the screen saver or not

Waiting Time

5~60 min

Set the screen saver waiting time

Glint speed

1~10

Set the screen saver mark move speed

Snapshot Type

JPG/BMP/DCM

To select the default snapshot type.

Driver

Local Disk

To select the default driver

Disk/Removable

1.4 Preset Parameters of Exam Mode The system has five exam modes, which are abdomen (general), gynecology, cardiac, obstetric and small parts. Each exam mode has preset the most suitable operating environment. The preset contents of different exam modes are similar. Now use the obstetric exam as an example to illustrate how to preset the operating environment. The preset dialog box of the obstetric exam has three pages, which are “Parameter”,” B IP” and “M IP”. Parameter preset 1.

Select the [Obstetric] item in the PRESET menu, the dialog box of “Ob Preset” pops up. 1-4

Preset

The default is that Parameter page is opened. The dialog box is as shown in the following figure. The preset items are shown in table 1-2. 2.

Move the cursor onto the adjustment button for the parameter item to be modified, and press the 『Set』or『Back』key to modify the parameters. At this time the prompt information is displayed in the help information bar.

1-5

Preset

Table 1-2 the preset items in the parameter page Item

Selections

Description

Mode

To select the image mode.

Power

B M B RT + B B + B RT M + B RT 0~15

Depth

2.16-24.8cm

Focuses Scan Den Angle Probe Frq H Rev V Rev B Gray Map M Map B IP

Gray

To set the acoustic power in 16 steps. To set the scanning depth which has 20 steps for low-frequency probe.

1/2/3/4 Hi Density / Hi Frm Rate 0/1/2/3 All probes that the system supports. F1, F2, F3 √/ √/ Map1/Map2/Map3/ Map4/Map5 Map1/Map2/Map3/ Map4/Map5 1~8

M IP

1~8

M Speed B Gain

1/2/3/4 0~98

M Gain

0~98

TSI

General/Muscle/Fatty/Fluid

1-6

Scanning depth for high-frequency probe has 10 steps. To set the number of focuses To select the scan density To set the scan angle of the probe To select the type of probe To set the probe frequency To set the attribute of the L/R flip To set the attribute of the U/D flip To set the post processing effect of the B image. To set the post processing effect of the M image. To set the combination of parameters for B image processing in 8 steps. To set the combination of parameters for M image processing in 8 steps. To set the M mode scanning speed. To set the B mode image gain in 49 steps. To set the M mode image gain in 49 steps. To set the characteristic of the tissue

Preset

B IP preset 1.

Select the [B IP] preset page. See the dialog box below. The preset items are shown in table 1-3.

2. Move the cursor onto the adjustment button for the parameter item to be modified, and press the『Set』or『Back』key to modify the parameters. At this time the prompt information is displayed in the help information bar.

„

Table 1-3 the preset items in the B IP preset page Item

Optional Item

Functional Description

Dyn Rng

30 ~ 90

To set dynamic range in 16 steps with the increment of 4.

Edge

0~3

To set edge enhancement in 4 steps.

Smooth

0~3

To set smooth processing in 4 steps.

Frame Avg

0~7

To set frame average in 8 steps.

Soften

0~3

To set image soften in 4 steps.

B AGC

0~3

To set B AGC in 4 steps.

Noise Rst

0~3

To set Noise Rst in 4 steps.

1-7

Preset

M IP preset 1. Select the [M IP] preset page. See the dialog box below. The preset items are shown in table 1-4. 2.

Move the cursor onto the adjustment button for the parameter item to be modified, and press the『Set』or『Back』key to modify the parameters. At this time the prompt information is displayed in the help information bar.

Table 1-4 the preset items in the M IP preset page Item

Optional Item

Functional Description

Dyn Rng

30 ~ 90

To set dynamic range in 16 steps with the increment of 4.

Edge

0~3

To set edge enhancement in 4 steps.

Smooth

0~3

To set smooth processing in 4 steps.

M Soften

0~7

To set M image soften in 8 steps.

After all the parameters are set, press the 『OK』button, and all the settings become effective and be stored in the system. To cancel these settings, press the 『Cancel』button

1-8

Preset

1.5 Preset Formula Formula Presets define formulae including GS, CRL, BPD, HC, AC, FL, EFW, TAD, APAD, CER, FTA, HUM, OFD, THD, and BSA. Select “Formula” item in PRESET menu to open “Formula Preset” page, shown in figure below.

The following table gives us the description of the preset items in the dialog box.

Preset items GS

CRL

Options Rempen, Hansmann, China Tokyo, Hellman, Hadlock, Nelson, Robinson, Rempen, Hansmann, Osaka, China Tokyo, Jeanty,

GA calculating data FG+GA FG+GA GA FG+GA FG FG+GA GA FG+GA FG+GA FG+GA FG+GA GA FG+GA GA

1-9

Preset

Preset items BPD

HC

AC FL

EFW

TAD APAD CER FTA HUM OFD THD BSA

Options Hadlock, Jeanty, Kurtz, Sabbagha, Hansmann, Merz, Rempen, Osaka; China Tokyo, Hadlock, Jeanty, Merz, Hansmann, Hadlock, Jeanty, Merz, Hadlock, Jeanty, Hohler, Merz, Hansmann, O’Brien, Warda, Osaka, China Tokyo, Hadlock1, Hadlock2, Hadlock3, Hadlock4, Shepard, Campbell, Merz1, Merz2, Hansmann, Osaka; Tokyo, Merz; Merz; Hill, Goldstein; Osaka; Jeanty, Merz; Merz, Hansmann, Hansmann; Occidental Oriental,

GA calculating data FG+GA GA FG FG FG+GA FG+GA FG+GA FG+GA GA FG+GA FG+GA GA FG FG+GA FG+GA FG FG FG+GA GA GA FG+GA FG+GA FG FG+GA FG+GA GA FG+GA / / / / / / / / / / / FG FG FG+GA FG FG+GA GA FG FG FG+GA FG+GA / /

1-10

Preset

Before selecting formulae, please read the note as following. NOTE: FG and GA are used in these formulae. In formula preset, three situations are presented for each item. Some formulae are included in both FG and GA tables but others are exclusive for GA or FG table. Please select reasonable formula according to below information: 1.

In the process of obstetric measurement, if the user does not enter LMP or BBT, GA table

of formula will be required for calculating GA. If the formula have not GA table, the system will not display GA. 2.

If the user has entered LMP or BBT, FG table will then be required for calculating GA.

And the system will calculate GA based on FG table for all obstetric measured items. And at the same time the result window and report will be refreshed. If the formula have not FG table, the system will not display GA. 3.

Data of growth curve are all sourced from FG table. The user could select the formula in

the pull-down list. The system will accordingly display the growth curve corresponding to the formula. The initial curve being displayed is decided by the preset formula. If the formula does not have corresponding FG table, fetal growth curve will not be displayed.

1-11