multi_patient_use_mask_disinfection_and_sterilizati.pdf
Page 1
Disinfection and Sterilization Guide
This guide is intended for multi-patient use of a Fisher & Paykel Healthcare mask in the hospital, or other clinical settings, where proper
disinfection/sterilization of the device must occur between patients. If you use the mask as a single-patient user in the home,
please refer to your mask user instructions under “Cleaning your mask at home”.
Note: Only masks listed in the table below have been validated according to these instructions for reprocessing between patients
High level thermal disinfection
High level chemical
disinfection
In line with EN ISO 15883, the uncertainty range
for disinfection temperature is -0°C and +5°C
Mask
Replace these parts
with new parts
between patients
1min at 90 °C (194 °F)
10mins at 80 °C (176 °F)
30mins at 75 °C (167 °F)
CIDEX® OPA1, MetriCide™
OPA Plus2 or Rapicide®
OPA/283.
Sterilization
Sterrad®4.
Validated
number of
cycles
REF 185048234 REV D 2017-10 © 2017 Fisher & Paykel Healthcare Limited
Nasal masks
F&P Eson™ 2
Diffuser;
Seal - see note under
Cidex OPA
(Replace seal)
100S, 100NX, NX
20
F&P Eson™
Diffuser mats;
Seal - see note under
Cidex OPA
(Replace seal if
discolours)
100S, 100NX, NX
20
(Replace seal if
discolours)
100S, 100NX, NX
20
100S, 100NX, NX
20
Full Face masks
F&P Simplus™
Seal - see note under
Cidex OPA
Nasal Pillow masks
F&P Brevida™
Diffuser
F&P Pilairo™ Q
Diffuser mats
1.
2.
3.
4.
Product of Advanced Sterilization Products, division of Ethicon Inc., a Johnson & Johnson company.
Product of Metrex™ Research, LLC.
Product of Medivators Inc.
Product of Advanced Sterilization Products, division of Ethicon Inc., a Johnson & Johnson company.
www.fphcare.com
20
0123
Page 2
Validated disinfection and sterilization procedures
Point of Use
Remove any gross soiling on the mask by wiping or rinsing in potable water.
Disassembly
Disassemble the mask according to the instructions shown in the relevant mask’s Instructions For Use.
Masks should always be properly cleaned before further reprocessing is undertaken, failure to do this may result in ineffective disinfection/sterilization.
Cleaning
Drying
Soak all reprocessable parts of the mask in a solution of mildly alkali, anionic detergent e.g. Alconox5 according to the manufacturer’s instructions (at 1% concentration and 50°C for 10mins),
ensuring that no air bubbles are present on the device surface. Using a soft non-metallic brush (e.g. medium-hard toothbrush)*, vigorously brush the mask parts until visibly clean but not for
less than 10 seconds. Pay close attention to crevices and cannulations, such as the join between the silicone seal and plastic housing and the socket between the elbow and frame, and elbow
and tube. Rinse by submerging in 5 litres of demineralised water and agitating for at least 10 seconds. Repeat rinse.
*An additional thin bottle brush is required to access the inside of the Brevida Nasal Pillows Mask tube.
Make sure mask components are thoroughly dry before continuing, to ensure effective disinfection/sterilization. This can be done with a lint-free cloth, or by leaving to air dry out of direct sunlight.
High Level Thermal Disinfection
High Level Chemical Disinfection
Sterilization
For all reprocessable components:
Disinfection or Sterilization
Soak in a water bath or run a disinfection cycle in an automatic
washer-disinfector using one of the time/temperature
combinations shown on the front page of this guide. These time/
temperature combinations are consistent with EN ISO 15883 and
are equivalent in terms of known thermal inactivation kinetics of
vegetative micro-organisms, meeting an A0 of 600.
1. Immerse completely in an undiluted bath of CIDEX® OPA,
MetriCide™ OPA Plus or Rapicide® OPA/28 at 20°C for 12
minutes, ensuring that no air bubbles are present on the
device surface.
Utilize a STERRAD NX, 100S or 100NX Sterilization System
according to the manufacturer’s instructions, using the pouch
method.
2. Rinse thoroughly following the manufacturer’s rinsing
instructions.
Drying
Allow all components to air dry out of direct sunlight.
Inspection
Before each use, inspect the mask for deterioration. If any visible deterioration of a mask component is apparent, the mask component should be discarded and replaced. Some discolouration
may occur after reprocessing and is acceptable.
Reassembly
Reassemble the mask according to the instructions shown in the relevant mask’s Instructions For Use, or Use and Care Guide.
Storage
Ensure the mask is completely dry before storing. Store in clean conditions out of direct sunlight. Storage temperature: -20°C to 50°C (-4°F to 122°F)
Cleaning the Headgear
The headgear does not require disinfection or sterilization. Thoroughly washing the headgear between patients is acceptable.
1. Hand-wash the Headgear Assembly in soap dissolved in lukewarm water. Do not soak for more than 10 minutes.
2. Rinse thoroughly with fresh water, ensuring that all soap residue is removed.
3. Leave all parts to air dry out of direct sunlight before reassembling.
General Warnings and Cautions
The instructions provided above have been validated as being capable of preparing the masks for re-use. Fisher & Paykel Healthcare does not recommend any deviations from the
recommended method of reprocessing. The following actions may deteriorate or damage the mask and shorten its life:
• Do not iron the headgear
• Do not clean the mask with products containing alcohol, anti-bacterial agents, antiseptic, bleach, chlorine or moisturizer.
• Do not wash the mask in a dishwasher.
NB. If your Fisher & Paykel Healthcare mask weakens or cracks, discontinue use and seek replacement immediately.
5. Product of Alconox Inc.
Manufacturer
Fisher & Paykel Healthcare Ltd, 15 Maurice Paykel Place, East Tamaki, Auckland 2013, PO Box 14 348, Panmure, Auckland 1741, New Zealand Tel: +64 9 574 0100 Fax: +64 9 574 0158 Email: info@fphcare.co.nz Web: www.fphcare.com Australia (Sponsor) Fisher & Paykel Healthcare Pty Ltd,
19-31 King Street, Nunawading, Melbourne, Victoria 3131.Tel: +61 3 9871 4900 Fax: +61 3 9871 4998 Austria Tel: 0800 29 31 23 Fax: 0800 29 31 22 Benelux Tel: +31 40 216 3555 Fax: +31 40 216 3554 Brazil Fisher & Paykel do Brasil, Rua Sampaio Viana, 277 cj 21, Paraíso, 04004-000, São Paulo – SP, Brazil
Tel: +55 11 2548 8002 China 代理人/售后服务机构:费雪派克医疗保健(广州)有限公司, 广州高新技术产业开发区科学城科丰路31号G12栋301号 电话: +86 20 32053486 传真: +86 20 32052132 Finland Tel: +358 (0)405 406618 Fax: +46 (0)8 36 6310 France Tel: +33 1 6446 5201 Fax: +33 1 6446 5221
Germany Tel: +49 7181 98599 0 Fax: +49 7181 98599 66 India Tel: +91 80 4284 4000 Fax: +91 80 4123 6044 Irish Republic Tel: 1800 409 011 Italy Tel: +39 06 7839 2939 Fax: +39 06 7814 7709 Japan Tel: +81 3 5117 7110 Fax: +81 3 5117 7115 Korea Tel: +82 2 6205 6900 Fax: +82 2 6309 6901
Northern Ireland Tel: 0800 132 189 Russia Tel and Fax: +7 495 782 21 50 Spain Tel: +34 902 013 346 Fax: +34 902 013 379 Sweden Tel: +46 8 564 76 680 Fax: +46 8 36 63 10 Switzerland Tel: 0800 83 47 63 Fax: 0800 83 47 54 Taiwan Tel: +886 2 8751 1739 Fax: +886 2 8751 5625
Turkey Fisher Paykel Sağlık Ürünleri Ticaret Limited Şirketi, Alinteri Bulvari 1161/1 Sokak No. 12-14, P.O. Box 06371 Ostim, Ankara, Turkey Tel: +90 312 354 34 12 Fax: +90 312 354 31 01 UK
Fisher & Paykel Healthcare Ltd, Unit 16, Cordwallis Park, Clivemont Road, Maidenhead, Berkshire SL6 7BU, UK Tel:
+44 1628 626 136 Fax: +44 1628 626 146 USA/Canada Tel: 1800 446 3908 or +1 949 453 4000 Fax: +1 949 453 4001