VisionPro 26” 4K LED Display REF 0240-031-020 and 240-031-000 Instructions for Use June 2020 PDF download

VisionPro 26" LED Display VisionPro 26" LED Display: 0240-031-020 VisionPro SYNK 26" Wireless LED Display: 0240-031-000

Table of Contents Warnings and Cautions...1 About Your Device...3 Intended Use and Indications for Use ��4 Contraindications��4 Package Contents ��5 Device Features ��6 Setup... 11 Connections �� 11 Basic Video Setup �� 13 Operation... 14 On-Screen Display (OSD) �� 14 OSD Menus �� 16 Troubleshooting �� 18 Cleaning and Maintenance... 19 Technical Specifications... 20 Electromagnetic Compatibility... 22 Symbols and Definitions... 25

Warnings and Cautions Please read this manual and follow its instructions carefully. The words warning, caution, and note carry special meanings and should be carefully reviewed: Warning: Indicates measures to avoid potential serious injury to the user and the patient. Caution: Indicates risks to the equipment. Failure to follow cautions may result in product damage. Note: Provides special information to clarify instructions or present additional useful information.

Warnings To avoid potential serious injury to the user and the patient, please note the following warnings: 1. Read this manual thoroughly and be familiar with its contents prior to using this device. 2. Federal law (United States of America) restricts this device to sale by, or on the order of, a physician. 3. Carefully unpack the device and check if any damage occurred during shipment. 4. This device is non-sterile and therefore should not be placed in the sterile field. 5. Do not place the device or any other heavy object on the power cord. Damage to the cable can cause fire or electric shock. 6. To avoid electric shock, avoid removing the bezel. 7. This device should not be used adjacent to or stacked with other devices. If adjacent or stacked use is necessary, the device should be observed to verify normal operation in the configuration in which it will be used. 8. Test this device prior to a surgical procedure. This device was fully tested at the factory before shipment. 9. Do not attempt internal repairs or adjustments not specifically detailed in this manual. Ensure that readjustments, modifications, and/or repairs are carried out by persons authorized by Stryker Endoscopy. 10. Do not put any object into the panel. If this occurs, unplug the device and have it checked by qualified personnel before operating it any further. 11. Use appropriate caution to prevent contact with fluids if the device is being used with a power supply in patient environments. 12. The use of cables and/or other accessories with this device, other than those specified, may result in increased emissions or decreased immunity of this device.

Cautions 1. 2. 3. 4.

Connect the device to an AC adapter connected to a hospital grade power cord ensuring the power cord is plugged into a grounded power outlet to achieve grounding reliability. Do not sterilize the device, as the delicate electronics cannot withstand this procedure. Use only the proprietary surgical display power supply for the display. Completely secure the connection between the DC power cord and the extension cord. Never operate the device immediately after transportation from a cold location to a warm location. 1

5.

To connect to an international power supply, use an attachment plug appropriate for the power outlet, as outlined in the "Technical Specifications" section of this manual. 6. Unplug the device if it is not to be used for an extended period of time. To disconnect the cord, unscrew the plug first, then pull the cord out by the plug. Never pull the cord itself. 7. Do not expose the device to moisture or apply liquid cleaners directly to the screen. Spray the cleaning solution onto a soft cloth and clean gently. For further detail, refer to the "Cleaning and Maintenance" section of this manual. 8. Allow adequate air circulation to prevent internal heat buildup. Do not place the device on surfaces (rugs, blankets, etc.) or near materials (curtains, draperies) that may block the ventilation slots. The device is cooled by natural convection and has no fan. 9. Do not touch the patient with signal input or output connectors. Equipment with SIP/ SOP connectors should either comply with IEC 60601-1 and/or IEC 60601-1-1 harmonized national standards or the combination should be evaluated for safety. 10. To ensure electromagnetic compatibility, refer to the “Electromagnetic Compatibility” section of this manual. The VisionPro 26” LED Display (0240-031-020) and the VisionPro SYNK 26” Wireless LED Display (0240-031-000) must be installed and operated according to the EMC information provided in this manual. 11. Pay close attention to the cleaning instructions in this manual. A deviation may cause damage. 12. Do not install the device near sunlight, excessive dust, mechanical vibration, or shock. 13. Do not position the device so that it is difficult to disconnect the power cord from the supply mains. 14. Do not operate with the glass device screen facing downward. 15. Handle the device with care. Do not strike or scratch the screen. 16. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the device. 17. Note: This device has been tested and found to comply with the limit for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. There is no guarantee that interference will not occur in a particular installation, which can be determined by turning the device off and on. The user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving device. • Increase the separation distance between the device. • Connect the device to an outlet on a circuit different from that to which the other device(s) are connected. • Consult the manufacturer or field service technician for help. The warranty is void if any of these warnings or cautions are disregarded. This product contains electrical waste or electronic equipment. It must not be disposed of as unsorted municipal waste and must be collected separately.

2

About Your Device VisionPro 26” LED Display REF: 0240-031-020

The VisionPro 26” LED Display is a wide screen LED surgical display that can support a maximum resolution of WUXGA (1920x1200). The display supports the following video inputs: digital RGB, analog RGB, serial digital interface (SDI), component video (YPbPr/RGBS), S-video, and C-video/ SOG. It also supports serial communication via the RS232 port.

VisionPro SYNK 26” Wireless LED Display REF: 0240-031-000

The VisionPro SYNK 26” Wireless LED Display can be used with the optional SYNK Transmitter (0240-031-010), which allows it to receive a high-definition video signal over a radio-frequency link. The display supports the following video inputs: DVI, S-Video, and C-Video/SOG. Once the wireless functionality is enabled, the display supports a wireless digital RGB video input. The display also supports a USB port and serial communication via the RS232 port. Note: The wireless functionality of the VisionPro SYNK 26” Wireless LED Display can only be enabled via the SYNK Transmitter. For details and instructions on using the SYNK Wireless Transmitter and the wireless functionality of the VisionPro SYNK 26” Wireless LED Display, refer to the SYNK Wireless System manual (P21693).

3

Intended Use and Indications for Use The VisionPro SYNK 26” Wireless LED Display and the VisionPro 26” LED Display are intended for video display during surgical procedures including arthroscopy (orthopedic surgery), laparoscopy (general and gynecological surgery), thoracoscopy, endoscopy (general, gastroenterological, and ENT surgery) and general surgery. The display is a non-sterile reusable device not intended for use in the sterile field. The display is intended for use by qualified physicians having complete knowledge of these surgical procedures.

Contraindications There are no known contraindications for this device.

4

Package Contents

1

2 4 3

5

Reference

Part Number

Package Contents

1

0240-031-020 0240-031-000

VisionPro 26” LED Display or VisionPro SYNK 26” Wireless LED Display

2

–

(4) M4 × 16 mm VESA screws

3

–

Hospital-grade AC power cord

4

0240-031-004

Medical Power Supply

5

–

Cable Cover

Part Number

Optional Accessories

0240-031-002

VisionPro 26” Display Cover

0240-031-004

Medical Power Supply

0240-031-010

SYNK Wireless Transmitter

0240-030-951

15-ft. (5 pin) DC extension cable

0240-030-952

75-ft. (5 pin) DC extension cable

5

Device Features Front panel Operate the display using the rotary control located on the front panel. A list of the display controls and their functions is provided below.

1

2

3

4

5

1. 2. 3.

Display Screen Power switch (soft) Power LED

4.

Token slot (VisionPro SYNK 26” Wireless LED Display only) Token LED (VisionPro SYNK 26” Wireless LED Display only) Auxillary Connection

5.

6.

6

7

8

9 10

11

Shows video image. Powers the display ON and OFF. Indicates current status: Green - Display is powered on or is in screen saver mode Blinking Red - Display is in sleep mode Blinking Amber - Over or under voltage Token insertion site used to establish a wireless connection with the transmitter. Green - Link is established Amber - Initializing Blinking Amber - Error, contact service representative Supports auxilliary device connections.

7.

Audio/PIP

8. Bright 9. Specialty 10. Input 11. Rotary control

VisionPro 26” LED Display: Accesses the Picture in Picture adjustment menu. VisionPro SYNK 26” Wireless LED Display: Press twice for Picture in Picture adjustment menu. Note: Audio functionality is not enabled at this time. Accesses the Brightness adjustment menu Accesses the Specialty adjustment menu Accesses the Input Selection menu Accesses the on-screen display and navigates through its functions.

7

Rear panel 1

12

11

2

10 3

1

4

1 9

5

6

1.

Accessory mounts (3)

2. 3. 4. 5.

VESA mounting holes Power switch (hard) Power connector Handles

6. 7. 8.

Cable cover hinges Velcro straps Cable cover thumbscrews

9. Cable cover 10. Cable cover clips 11. Cable wrap 12. Locking feature

8

7

8

Provide an access point for mounting optional accessories. Provide access points for mounting the display. Powers the input DC power ON and OFF. Connects to the 24V DC power supply. Aid in display positioning. Caution: The handles are not intended to bear the entire weight of the display Attach the bottom of the cable cover to the display. Straps aid in cable management. Attach the cable cover to the display, and are tightened or loosened using fingers. Covers and conceals cables. Attach the top of the cable cover to the display. Provides a location for wrapping cables. A locking mechanism or cable may be routed here for security purposes.

Cable Cover

Installing the Cable Cover 1. Align the left and right hinges of the cable cover onto the bottom rear of the display. 2. Snap on the top section of the cable cover to the aligning clips. 3. With your fingers, turn the thumbscrews clockwise to tighten and lock the cable cover onto the display. Removing the Cable Cover 1. With your fingers, turn the thumbscrews counterclockwise to loosen. 2. Once the thumbscrews are completely loosened, pinch the left and right clips and pull the cable cover towards you. 3. Remove the cable cover from the left and right hinges.

9

Display Handles

Caution: The handles are intended to aid in positioning the display, not for transporting the display. The handles should not bear the full weight of the display. Removing the Display Handles 1. Using a 3mm hex key, loosen the two M4 x 30mm screws and gently pull the handle away from the display. Installing the Display Handles 1. Align the handle with the screw holes on the rear of the display. 2. Using a 3mm hex key, install the two M4 x 30mm screws to attach the handle.

10

Setup Stryker Endoscopy considers instructional training, or inservice, an integral part of this device. Your local Stryker Endoscopy sales representative will perform at least one inservice at your convenience to help set up your device and instruct you and your staff on its operation and maintenance. To schedule an inservice, contact your local Stryker Endoscopy representative after your device has arrived.

Connections VisionPro 26” LED Display Connection Ports Video input and output signals are connected to the rear of the display, as illustrated below:

1

1. 2. 3. 4. 5. 6.

2

DVI 3G/HD/SD SDI-in 3G/HD/SD SDI-out VGA S-Video C-Video/SOG

3

4

5

6

7

8 6

9 6

10 6

11 6

12 6

7. R/Pr 8. G/Y 9. B/Pb 10. H-sync 11. V-sync 12. RS232

11

VisionPro SYNK 26” Wireless LED Display Connection Ports

1

1. 2. 3.

DVI S-Video C-Video/SOG

2

3

4

4. 5. 6.

5 6

6

Auxillary Connector USB RS232

Connecting the Power Supply

1. 2. 3. 4. 5.

Connect the power supply to the 24V input on the display. Connect the AC power cord to the power supply*. Connect the AC power, using the supplied hospital-grade power cord. (Optional, not shown) Connect an extension cord between the power supply and display. Install cable cover.

* Power supply information: Model Number: BPM150S24F11, Manufacturer: Bridgepower Corp.

12

Basic Video Setup

2

1

1. 2.

Route the video output 1 from the camera to the SDC DVI input. Route the video output 1 from the SDC DVI output to the DVI input on the display.

Note: Stryker recommends a backup connection to the camera.

13

Operation Operate the display using the rotary control and the four buttons located on the front panel. A list of the display controls and their functions is provided below.

On-Screen Display (OSD) Accessing the On-Screen Display

1

2

3

4

To use the four front-panel buttons: 1. Audio/PIP (VisionPro SYNK 26” Wireless LED Display): • Press twice to activate Picture Mode (Picture in Picture, Picture by Picture, Picture on Picture) 2. PIP (VisionPro 26” LED Display): • Press to activate Picture Mode (Picture in Picture, Picture by Picture, Picture on Picture) 3. Bright: Activates the Brightness adjustment menu. 4. Specialty: Activates the Specialty adjustment menu. 5. Input: Activates the Input selection menu. Use the Rotary Control to navigate the on-screen menus once they are activated: • Push - Accesses/selects on-screen display menu. • Turn Right/Left - With the on-screen display menu activated, turning increases/decreases the value of the selected parameter. • Push and Hold - Exits on-screen display menu.

14

Operating On-Screen Display The device OSD helps navigate through various device menus. 1. Press the Rotary Control to activate the OSD menu. 2. Rotate the Rotary Control to move up or down through the menu. The parameter is highlighted when selected. 3. Press the Rotary Control to enter the next level OSD. 4. Rotate the Rotary Control to increase or decrease the value of the selected parameter, or to make a selection on different options. 5. To exit the OSD menu screen from the second or third level OSD menu, select the Exit option. To completely exit the OSD, press and hold the Rotary Control. If no keys are pressed, the OSD will automatically exit after the factory-set predetermined time (the time is customizable).

15

OSD Menus Speciality Menu Item

Description

Range

Color Temperature*

Chooses between color temperatures for Lap A, Lap B, Arthro A, Arthro B, Standard, PACS, NORM, ENT, GYN.

-

Red

Red balance

-128 – 127

Green

Green balance

-128 – 127

Blue

Blue balance

-128 – 127

Gamma

Gamma value

0.1 – 2.5, S0, S1, S2

*

Color Temperature RGB adjustment is available only for Standard, Arth, and Lap settings. PACS and Norm adjustments are only avaliable under SOG input.

Audio (Menu not active at this time) Brightness Settings Menu Item

Description

Range

Brightness

Increases or decreases the brightness

0 – 100

Contrast

Increases or decreases the contrast

0 – 100

Phase**

Increases or decreases the Phase level

0 – 100

Chroma**

Increases or decreases the Chroma level

0 – 100

Image Sharpness

Sets image sharpness

1 – 10

Video Sharpness**

Increases or decreases the video sharpness

0 – 100

**

Only available under SDI-, S-, or C-video input.

Image Effect Menu Item

Description

Scale Mode

Chooses scale mode between Fill All, V-Fill, H-Fill, One-To-One, or Fill-Aspect

Freeze Frame

Enables or disables freeze frame

PIP

Enables PIP (picture in picture) function

POP

Enables POP (picture on picture) function

PBP

Enables PBP (picture by picture) function

16

Advanced Settings Menu Item

Description

Key Lock

Key lock on: Disables all key functions Press and hold the rotary knob to turn off key lock.

Auto Source Select

Scans inputs until an active video source is detected. Auto Source Select is disabled during PIP/POP/PBP mode.

Sleep Timer

On: The display enters sleep mode if no active video source is detected. Off: The display will not enter sleep mode. Timer: Set the time until the display enters sleep mode if no active video source is detected.

OSD Control

Controls OSD (On Screen Display) Menu Position, Background, and Timeout

Restore Factory Settings

Sets to factory default

Screen Control

VGA

• • • •

Horizontal Vertical Phase Frequency

S-Video, C-Video, SOG, RGBs, Component

• •

Horizontal Vertical

SYNK (for the VisionPro SYNK 26” Wireless LED Display) Status

Description

RX APP: XX.XX.XX RX MAC: XX.XX.XX.XX

Receiver

TX APP: XX.XX.XX TX MAC: XX.XX.XX.XX

Transmitter

WiFi SW: XXX-X.XX SIGNAL = Excellent, Good, Poor Default Region: XX FREQ: XXXX MHz

Transmitter

Information Menu Item

Description

User Name Entry

Enters custom user name display for boot-up display

Serial Number

Displays device serial number

Runtime

Displays current device total run time

Input Format

Displays current input format

Note: Actual on-screen display values may vary with updated versions of the firmware and user settings. 17

Troubleshooting Before returning your display for service, consult the troubleshooting list below: Problem

Current Status

Remedy

No picture

Power LED on

Using the OSD Menu, adjust the brightness and contrast to maximum, or reset them to their default settings.

Power LED off

Ensure the power switch at the front and rear of the display are set to ON. Check if the AC power cord is properly connected to the AC adapter and outlet. Check that the power supply is fully connected and functioning properly.

Power LED blinking

Abnormal picture

Oversized, undersized, or missing video; or center shift.

Red

Display is in sleep mode. Press any key to wake the display.

Amber

The power supply may be over or under voltage.

Using the Screen Control Menu, adjust the Phase, Frequency, Horizontal, and Vertical settings in order to correct the display image. Adjust settings in Scale Mode For VGA input only: push and hold the rotary control for 1-2 seconds to re-sync the video feed. Wait a few seconds after initial sync of video signals, or power cycle the display.

OSD error message

“Out of Range”

Ensure that an acceptable video source is connected.

Token LED blinking amber

Error

Contact service representative.

18

GAYMAR

Monitors

VisionPro 26” 4K LED Display REF 0240-031-020 and 240-031-000 Instructions for Use June 2020