Operating Manual
32 Pages

Preview
Page 1
Shaking Water Bath LSB Aqua Pro Operating Manual
www.grantinstruments.com [email protected] LSB Aqua Pro Tel: +44 (0)1763 260811 Detailed operating manual www.grantinstruments.com
32138 V1 Page 1
Original instructions If you have any feedback on Grant’s products or services we would like to hear from you. Please send all feedback to: Grant Instruments (Cambridge) Ltd Shepreth Cambridgeshire SG8 6GB UK Tel: +44 (0) 1763 260 811 Fax: +44 (0) 1763 262 410 E-mail: [email protected] Contents 1 2 3 4
Use of products How to use this operating manual Product registration and warranty Safety information 4.1 Safety symbols 4.2 Safety warnings 5 Operating instructions 5.1 Unpacking instructions 5.2 Installation 5.3 Electrical supply 5.4 Selecting and configuring trays and racks 5.5 Fitting the shaking trolley and a tray 6 Operating procedures 6.1 Bath liquids 6.2 Liquid level 6.3 Run-dry protection 6.4 Operation above 60°C 6.5 Achieving high temperature accuracy when shaking is used 6.6 Use as a thermostatic bath without shaking 6.7 Emptying the baths 7 Using the shaking water bath 7.1 Bath controls 7.2 Indicators 7.3 Setting the control temperature () 7.4 Setting the shaking speed 7.5 Stopping and starting the shaking 7.6 Enabling the keypad lock 7.7 Setting the over temperature protection () 7.8 Configuring and running temperature and shaking speed presets (, ) 7.9 Running temperature presets (, ) 7.10 Setting the countdown timer () 8 Calibration 8.1 Calibration options 8.2 Single point calibration () 8.3 Dual point calibration (, ) 9 Technical specification 10 Technical tips 10.1 Which water should you use in your bath? 10.2 Troubleshooting guide 11 Warranty information LSB Aqua Pro Detailed operating manual
4 4 4 5 5 5 7 7 7 7 7 9 10 10 10 11 12 12 12 12 13 13 13 14 14 16 16 17 18 19 19 21 21 21 23 26 27 27 28 28
32138 V1 Page 2 www.grantinstruments.com
12 Maintenance and service 12.1 Cleaning 12.2 Fuses 12.3 Replacing the mains cord 12.4 Routine safety tests 12.5 Service 13 Compliance
LSB Aqua Pro Detailed operating manual
29 29 29 29 29 30 30
32138 V1 Page 3 www.grantinstruments.com
1 Use of products The following products are covered by this operating manual: LSB Aqua Pro range: LSB12, LSB12 AUS, LSB12 US, LSB18, LSB18 AUS, LSB18 US, The products listed above are a general purpose series of thermostatically controlled linear and orbital shaking water baths designed for indoor laboratory use by a professional user.
2 How to use this operating manual This operating manual will allow you to unpack, set up and operate this water bath correctly and safely. Important safety information, symbols and warnings are listed below and should be read carefully. If there is a technical matter that this operating manual does not address, or any other questions concerning this product, please contact Grant Instruments or your local distributor who will be able to provide any additional information. English is the original language of this manual
3 Product registration and warranty The warranty for this water bath is detailed in section 8 but to register you should complete the on-line registration form at www.grantinstruments.com. Not registering your product may affect your warranty.
LSB Aqua Pro Detailed operating manual
32138 V1 Page 4 www.grantinstruments.com
4 Safety information 4.1
Safety symbols
The symbols below are marked on the equipment to indicate:
Caution: Surfaces and water can be hot during and after use Read this manual before using the bath Important safety warning Recommended operation Failure to follow may affect the performance of the equipment
4.2
Safety warnings
Read the whole of the instructions. Safety may be impaired if they are not followed.
Surfaces and water can be hot during and after use. Allow the liquid temperature to fall to a safe level before emptying. Empty the bath before moving it. This bath is only intended for use with water. Use of other fluids or heat transfer media may invalidate the warranty and present a risk of fire or explosion. Place on a stable flat surface to reduce the risk of accidental spillage. No user serviceable parts. Risk of electric shock after disassembly or operation with covers removed. Not for use in environments with a risk of flammable or explosive gases. To be operated within the limits listed in this guide Do not use the bath to heat any material that could cause a fire or any other kind of hazard. Take care when operating after a power interruption as shaking will restart at the previous speed. There are accessible moving parts in the bath. Observe safe working practises when operating a shaking bath. Users should not interfere with moving parts when in use and prevent accidental contact from items such as fingers, hair or clothing. Only use the mains cord provided or one with an identical rating. Ensure that the mains plug and the switch are easily accessible.
LSB Aqua Pro Detailed operating manual
32138 V1 Page 5 www.grantinstruments.com
A clearance of >10cm around the bath is required to ensure adequate air flow. If a potentially hazardous liquid is spilt onto the equipment, disconnect it from the power supply and have it checked by a competent person. It is the user’s responsibility to carry out appropriate decontamination if hazardous material is spilt on the equipment. Clean the outside of the equipment with a damp cloth, using water and domestic cleaning products only. The use of other chemical cleaning agents may damage the equipment. Always follow the manufacturer’s instructions and any applicable legislation about the use of potentially hazardous substances.
Before first switching on the bath please remember to fill the bath with water. Switching the bath on dry can damage the heater and could invalidate the product warranty. If the equipment has been transported or stored in cold or humid conditions, condensation may form inside it. If that could have happened, allow time (at least 2 hours at room temperature) for the condensation to evaporate before using the equipment. Restricting or interfering with the tray motion in the bath may reduce performance and reduce reliability
To preserve your water bath in peak condition consult the extra guidance listed in this manual. Failure to do so may affect your warranty. Consult online resources for additional important information.
LSB Aqua Pro Detailed operating manual
32138 V1 Page 6 www.grantinstruments.com
5 Operating instructions 5.1
Unpacking instructions
Standard equipment includes: Shaking water bath Shaking trolley Drive magnet Mains cord with plug Gabled polycarbonate lid Short user guide Remove packing materials carefully, and retain for future shipment or storage of the equipment. 5.2
Installation
Place the water bath on a level, non-combustible surface. Ensure that the mains plug and the switch are easily accessible. A clearance of >10cm around the bath is required to ensure adequate air flow. 5.3
Electrical supply
Check that the supply voltage marked on the serial number label, and the type of mains plug, are correct for your mains supply outlet, which must have an Earth (Ground) connection. To disconnect the equipment from the mains supply, remove the mains plug from the mains supply outlet. 5.4
Selecting and configuring trays and racks
Different types of shaking trays are available to hold different vessel types. These need to be purchased separately. See www.grantinstruments.com for a full list of accessories.
Part number TU12 TU18 TF12 TF18 TS12 TS18
Description Universal tray with adjustable springs, for LSB12. Highly versatile for a variety of vessel types Universal tray with adjustable springs, for LSB18. Highly versatile for a variety of vessel types Flask tray with threaded holes to hold 25 - 1000ml flask clamps, racks and deep well plate holder (see options below) for LSB12 Flask tray with threaded holes to hold 25 - 1000ml flask clamps, racks and deep well plate holder (see options below) for LSB18 Test tube tray compatible with SR test tube and microtube racks (see options below) for LSB12. Holds up to 3 SR racks Test tube tray compatible with SR test tube and microtube racks (see options below) for LSB18. Holds up to 5 SR racks
LSB Aqua Pro Detailed operating manual
32138 V1 Page 7 www.grantinstruments.com
Flask clamps and plate holder Part number Description SC-25 For 25ml flask SC-50 For 50ml flask SC-100 For 100ml flask SC-250 For 250ml flask SC-500 For 500ml flask SC-1000 For 1000ml flask SH-DWP For 1 x deep well plate (≥2ml) Test tube rack /microtube rack Part number SR-10 SR-13 SR-16 SR-19 SR-25 SR-30 Part number SR-SE SR-LE
TF12 capacity 18 14 9 5 4 2 2
Tube diameter (mm) 10 13 16 19 25 30 Micrstube size (ml) 0.5 1.5
TF18 capacity 33 26 17 14 6 4 4
Rack capacity 48 44 24 21 12 10 Rack capacity 119 48
Configure the tray to hold in place the type of vessel being used. The number flasks and vessels that can be fitted to each tray along with the suggested position of holding springs and flask clamps is available online at www.grantinstruments.com
LSB Aqua Pro Detailed operating manual
32138 V1 Page 8 www.grantinstruments.com
5.5
Fitting the shaking trolley and a tray
Tray
Trolley
Drive magnet
Locate the trolley arm pin into the hole on the drive magnet The tray can now be lowered directly on to the trolley and will be held in place
LSB Aqua Pro Detailed operating manual
32138 V1 Page 9 www.grantinstruments.com
6 Operating procedures 6.1
Bath liquids
Water is the only liquid permitted for use in the LSB Aqua Pro. See section 7.1 for more information 6.2
Liquid level
The best liquid level for your bath depends on the application and several factors must be considered:
When the shaking function is not in use the bath will provide optimum performance when filled to the swage line which is typically 25mm below the top of the tank. The water level used in the tank will influence the temperature accuracy and stability. Using liquid levels below the swage line needs consideration, especially when operating at higher water temperatures (>50ºC) and without a lid. When the shaking function is used the optimum liquid level depends on: o The tray type and vessel type in use. o The shaking mode and shaking speed o The minimum level which keeps the samples covered all the time and therefore allows their temperature to be properly controlled For a given shaking setting (speed/stroke length/orbital or linear) there will be a practical maximum level above which fluid from the bath will pushed over the sides of the bath by the motion of the vessels.
Do not fill above the swage line. Grant recommends the following minimum fill levels Bath LSB12 LSB18
Recommended minimum fill 5 litre 7.5 litre
Approximate water depth 60mm 60mm
Table 1 - Recommended minimum fill levels
Do not attempt to use your bath without water in the tank. The bath has an inbuilt protection mechanism known as dry start protection which will detect if the bath is started without any water, in most circumstances, and prevent the bath from continuing to heat. In this instance the bath will display and sound an alarm. Switch the bath off before filling it with water and switching on again. The bath will not resume operation without being turned off and on again..
LSB Aqua Pro Detailed operating manual
32138 V1 Page 10 www.grantinstruments.com
The tank internal surface can become very hot if an accidental dry start has occurred, even if the dry start cut out has operated. Avoid touching the tank until it has been left to cool for several minutes. Refill carefully, a hot heater can cause a spattering of very hot water droplets and scalding steam
Repeated dry starting of the bath stresses key components in the bath which can affect service life and the equipment’s warranty.
Allowing the bath to run dry Always take care to avoid allowing the water to evaporate to the point that the bath runs dry. This can lead to the bath’s internal safety cut-out operating requiring a suitable qualified technician to reset it.
6.3
Run-dry protection
The bath has a built-in advanced detection mechanism to greatly reduce the chances of the safety cut out occurring in most circumstances where the bath is left to accidentally run dry. This feature is only enabled automatically when the following criteria are met:
The set temperature is >50°C
The bath has been operating for a least one hour
The water is not set to boiling point (>=99ºC)
If the bath detects signs that the bath water level may be becoming low, it will alert the user by displaying and sounding an alarm Once you have checked the water level and topped up the water level as necessary you will need to switch the bath off and on in order to resume operation. For users with specialist applications where this feature may be unnecessarily triggered it can be disabled. Press the set key to enter the bath menu and use the arrow keys to select (Dry Protection Alarm). Press the set key and use the arrow keys to select off. Use the set key to confirm that the dry start and run dry protection are switched off. The bath also includes an independent safety temperature cut-out which will protect the bath in the unlikely event of a fault or if the dry protection alarm is switched off. If the cutout is activated then the bath will stop heating, show on the display and sound an alarm. The bath should be switched off, unplugged and allowed to cool for at least 30 minutes. The cut-out can only be reset by a suitably qualified technician who must verify that the bath has not been damaged.
LSB Aqua Pro Detailed operating manual
32138 V1 Page 11 www.grantinstruments.com
6.4
Operation above 60°C
The lid must be used above 60°C to maintain proper temperature control and to ensure that the water temperature reaches the set point. The lid will also prevent excessive evaporation that requires the bath to be filled more often and will save energy. The lid should only be lifted by the handle, as other parts can become hot during use. It also has a vent/thermometer hole – this hole should not be sealed as pressure could build up inside the bath. 6.5
Achieving high temperature accuracy when shaking is used
To achieve higher accuracy and temperature stability, Grant recommends the bath is calibrated with the bath running at the shaking speed typically used. Single and dual point calibration options can be set. See Section 8. When operating above 70°C, Grant recommends a minimum shaking speed of 50 rpm.
Restricting or interfering with the tray motion in the bath may reduce performance and reduce reliability
6.6
Use as a thermostatic bath without shaking
If the shaking trolley and drive magnet are lifted out, a shaking bath can be used as a simple thermostatic bath. When used in this way, if flat bottomed vessels or objects are to be placed in the bath, always use a steel base tray (optional accessory) to avoid damage to the under-tank heater.
6.7
Emptying the baths
Allow the liquid temperature to fall to a safe level before emptying. Take reasonable precautions to prevent accidental spillage. If the bath is drained at temperatures above 50°C then the drain mechanism will be damaged and will need to be replaced.
Baths have drain taps to make emptying easier. To empty the bath using the drain tap, push the supplied drain insert into the drain tap. Note that the water will begin to empty as soon as the drain insert is fully engaged. A length of hose can be added to the barbed end of the drain insert if required.
LSB Aqua Pro Detailed operating manual
32138 V1 Page 12 www.grantinstruments.com
7 Using the shaking water bath 7.1
Bath controls
Temperature and Display
Shaking speed rpm button
Shaking ON/OFF button
Up, down and set keys
Alarm indicator
Preset button
Heater indicator
Over temperature protection OTP button
Figure 1 – LSB Aqua Pro front panel controls
The mains on/off switch is at the rear of the unit 7.2
Indicators
There are three indicators: Main display – used to show temperature, shaking speed and short messages Heater – Illuminated when the bath is heating Alarm - flashes red when activated. A buzzer also sounds.
LSB Aqua Pro Detailed operating manual
32138 V1 Page 13 www.grantinstruments.com
7.3
Setting the control temperature ()
The water temperature of the bath can be set using the main display. The following example shows setting the water bath to 37.0°C.
. . . Figure 2 - Setting the control temperature
7.4
Setting the shaking speed
Press the rpm (revolutions per minute) button
Select speed between 20 and 200. The trolley will immediately start to move at the displayed speed
.
The speed value will automatically be saved. Press set or rpm button to quickly store the displayed speed
Figure 3 - Setting the shaking speed
The shaking speed can be checked at anytime by pressing the rpm button. The speed is displayed for 2 seconds. The bath shaking speed is dependent on how much the tray is loaded. If the shaking speed is set too high for a given tray load then the motion will judder and become erratic. If this happens, either reduce the shaking speed or the tray load until the motion becomes smooth and consistent.
LSB Aqua Pro Detailed operating manual
32138 V1 Page 14 www.grantinstruments.com
The following graphs show the shaking speed range achievable under certain tray loads and can be used for guidance. The graphs were created using Erlenmeyer flasks with a fill depth of 90mm. Factors such as fill level and vessel type will influence the maximum speed achievable. Best performance will be achieved where vessels are held securely.
LSB12
LSB18
If the shaking speed is changed by more 40rpm during operation, allow half an hour for the bath liquid temperature to stabilise. When above 70°C the recommended minimum shaking speed is 50 rpm to maintain temperature accuracy and stability.
LSB Aqua Pro Detailed operating manual
32138 V1 Page 15 www.grantinstruments.com
7.5
Stopping and starting the shaking
To stop the shaking, press button once
To start the shaking press button once
Figure 4 – Stopping and starting the shaking
The shaking will start at the speed previously set using the rpm button. If no speed has been set then the display will show when start is pressed. 7.6
Enabling the keypad lock
The keypad lock is intended to help users avoid accidental changes to the set point temperature of the bath. To enable and disable the lock, press and hold the set and up or down keys for three seconds as shown below
Locked
Unlocked
Figure 5 - Locking and unlocking the keypad
LSB Aqua Pro Detailed operating manual
32138 V1 Page 16 www.grantinstruments.com
7.7
Setting the over temperature protection ()
The over temperature protection can be used to protect samples by setting a maximum temperature limit the bath is allowed to heat to. If the bath exceeds this temperature, it will stop heating, display (over temperature alarm) and sound an alarm. The alarm can be silenced by pressing the set key. Allow the bath to cool below the over temperature value to resume normal operation. Note that if the cause of overheating is an incorrect set point, this will need to be corrected otherwise the alarm will operate again. You should set the over temperature value, allowing for a safety margin to the sample maximum temperature limit if possible. Additionally the limit should be greater than the bath set point to avoid nuisance alarms. Grant recommends this is at least 1°C. To set the over temperature alarm:
. .
If an over temp value has already been set the display will show the value and not off.
Set the value you wish to use – in this case 40ºC
The OTP is now set and the bath will display the current water temperature
Figure 6 - Setting the over temperature alarm
To disable the alarm, set the over temperature alarm limit to 10.0°C and then press the down button one further time so the display shows . Save this by pressing the over temperature alarm key.
LSB Aqua Pro Detailed operating manual
32138 V1 Page 17 www.grantinstruments.com
7.8
Configuring and running temperature and shaking speed presets (, )
Temperature and shaking speed presets allow you to conveniently store bath temperature and speed settings you routinely use. The bath has 2 presets, numbered , .
Before you can use presets you need to store the values you wish to use in at least one of the presets using the following sequence:
. 1
Press P. Preset 1 temperature can now be configured Set the value you wish to use – in this case 37ºC
Press P to store the value. Shaking speed preset 1 can now be configured Set the value you wish to use – in this case 120 rpm
Press the P to store the value. Preset 2 temperature can now be configured
.
Set the value you wish to use – in this case 75ºC
Press the P to store the value. Shaking speed preset 2 can now be configured
Set the value you wish to use – in this case 150rpm
Press the P to store the value. The display and shaking speed will return to the value before preset configuration was started
Figure 7 - Configuring a preset value
LSB Aqua Pro Detailed operating manual
32138 V1 Page 18 www.grantinstruments.com
7.9
Running temperature presets (, )
Running Preset 1
.
The Preset temperature is displayed momentarily before returning to the current bath temperature
Running Preset 2
X3
The Preset temperature is displayed momentarily before returning to the current bath temperature
Figure 8 – Running a preset
7.10 Setting the countdown timer () A countdown timer can be set in the range of 1 to 999 minutes. The countdown timer will sound an alarm at the end of a countdown period. It can be used to time experiments or remind you to take a further action. Note the countdown timer does not take into account if the bath has not reached the set temperature. If the bath has not reached the set temperature, this will need to be taken into account when starting the countdown timer.
LSB Aqua Pro Detailed operating manual
32138 V1 Page 19 www.grantinstruments.com
When the countdown timer expires the bath will sound an alarm and display . Press set to silence the alarm.
To set the countdown timer:
Select the menu option
. .
Select the countdown timer menu option
If a countdown timer value has already been set the display will show the value and not off. Set the value you require – in this case 10 minutes
Press the set key to start the timer. The remaining time will be displayed in minutes and seconds m.ss
>10 mins
..
Or if the countdown period is greater than 10 minutes the bath with automatically return to displaying the water temperature. An extra dot at the end of the temperature will flash to show the timer is operating
Figure 9 - Setting the countdown timer
To find out the water temperature whilst the display is showing the remaining time, press the set button. To enter the configuration menus whilst the display is showing the remaining time, press the set button twice. The timer can be turned off at any time by selecting the menu option and pressing the down arrow button until the display shows .
LSB Aqua Pro Detailed operating manual
32138 V1 Page 20 www.grantinstruments.com
8 Calibration 8.1
Calibration options
Two calibration options exist:
Single point calibration Dual point calibration
The quality of the calibration is highly dependent on: Use of a suitable reference thermometer, ideally 10 times the accuracy you are trying to achieve. Performing a calibration in a stable ambient environment (+/-1ºC) free from draughts or cooling air currents.
8.2
Single point calibration ()
A single point calibration applies a single offset over the bath temperature curve. For this reason the calibration temperature is usually the same as the intended working temperature for the bath or particular experiment:
LSB Aqua Pro Detailed operating manual
32138 V1 Page 21 www.grantinstruments.com
To configure a single point calibration: Firstly, set the bath to the working temperature and shaking speed and leave to stabilise for at least an hour. Place the reference thermometer either in the centre of the bath, or if using a lid, through the thermometer hole. Note the temperature shown by the reference thermometer and enter it into the calibration menu by following the steps below. Select the menu option
Select low point calibration LPC
Press set to enter the calibration value
.
Enter the reference thermometer value
.
Press set to store the calibration value
Leave the bath to stabilise and check the calibration
Figure 10 - Setting a single point calibration
LSB Aqua Pro Detailed operating manual
32138 V1 Page 22 www.grantinstruments.com
8.3
Dual point calibration (, )
Dual point calibration is typically used on baths which are operated over a range of temperatures. Two calibration points are entered into the calibration menu: the low calibration point () and high calibration point (). These points are typically selected as just below and above the normal working temperature range for the bath.
Note that if only one calibration point is entered then the bath will behave as described in Single point calibration above. To configure a dual point calibration, follow the steps below.
LSB Aqua Pro Detailed operating manual
32138 V1 Page 23 www.grantinstruments.com
Firstly set the bath to the lower working temperature and shaking speed and allow to stabilise for at least an hour. Place the reference thermometer either in the centre of the bath, or if using a lid, through the thermometer hole. Note the value of the reference thermometer and enter it into the calibration menu by following the steps below.
Select the menu option
Select single point calibration
Press set to enter the calibration value
F
.
.
Enter the reference thermometer value
Press set to store the calibration value
Leave the bath to stabilise and check the calibration
Figure 11 - Setting the low point calibration
LSB Aqua Pro Detailed operating manual
32138 V1 Page 24 www.grantinstruments.com
Secondly set the bath to the upper working temperature and shaking speed and allow to stabilise for at least an hour. Place the reference thermometer either in the centre of the bath, or if using a lid, through the thermometer hole. Note the value of the reference thermometer and enter it into the calibration menu by following the steps below. . Select the menu option
Select high point calibration HPC
Press set to enter the calibration value
F
.
.
Enter the reference thermometer value
Press set to store the calibration value
Leave the bath to stabilise and check the calibration
Figure 12 - Setting the high point calibration
LSB Aqua Pro Detailed operating manual
32138 V1 Page 25 www.grantinstruments.com
9 Technical specification Operating conditions Ambient Temperature Maximum relative humidity
5 to 40°C 80% R.H. in room temperatures up to 31°C decreasing linearly to 50 % R.H. at 40°C Up to 5,000 m (16,400 ft) Indoor use only
Altitude above sea level Operating Environment
Electrical details Mains supply: 220-240V @ 50/60 Hz or 110-120V @ 50/60 Hz Pollution degree: 2 Installation Category: II Note: Mains supply voltage fluctuations are not to exceed ±10% of the nominal supply voltage Models
Capacity (L)
Weight (kg)
LSB12 LSB18
12 18
9.2 11.2
Current rating (A) 120V 230V 6.5 3.6 9.0 6.2
LSB Aqua Pro bath performance Temperature range Display (also used for setting) Temperature stability
5°C above ambient to 99°C 10.0 to 99.0°C in 0.1°C steps ± 0.1°C
All performance data specified tested in accordance with DIN12876. Storage and transport Store and transport in original packaging. Temperature range -20°C to +60°C
LSB Aqua Pro Detailed operating manual
32138 V1 Page 26 www.grantinstruments.com
10 Technical tips 10.1 Which water should you use in your bath?
Use tap water with care. Water with a high lime content will cause scale build up and should be avoided.
Distilled water and some types of de-ionised water may be used. Avoid ultra high purity de-ionised waters.
Avoid using water with high levels of salts or iron. These will reduce the life of your bath
Regular water changing and frequent cleaning of your bath is needed to preserve the baths corrosion resistance
Ensure your bath is stored dry.
Use care in placing other metallic items in the bath. Some metals (e.g. ferrous materials such as iron filings and swarf) can cause an electro-chemical reaction leading to corrosion.
The product warranty may be affected by the use of inappropriate or corrosive liquids
Refer to www.grantinstruments.com for more additional information on corrosion prevention and cleaning guidance.
LSB Aqua Pro Detailed operating manual
32138 V1 Page 27 www.grantinstruments.com
10.2 Troubleshooting guide Sympton Unit does not operate
Possible cause Unit not switched on Unit not plugged into mains supply Mains power supply failure
Action Turn on at switch at rear of unit Plug in and switch on
Display shows
Overtemperature alarm has activated
Display shows
Bath is heating with insufficient liquid in the tank
Display shows and Alarm light on
Overtemperature cut-out has operated due to overheating
Check other appliances on the same circuit are working Check OTA temperature is set above the Control temperature and the current liquid temperature. See section 7.7 Switch off the bath, fill the bath with liquid. See section 6.2 for recommed fill level. Power the bath on to resume operation This cannot be reset by the user: have the unit checked by a competent person
Shaking speed has not been set Incorrectly fitted trolley
Check the DPA is set to ON. See section 6.3 Set shaking speed. See section 7.4 Refit trolley
Trolley not shaking when speed showes OFF Trolley not shaking when speed is not zero
Cannot set LPC or HPC
Speed is too high for load on trolley
Reduce shaking speed or reduce load in the tray and retry
Trolley is obstructed by limescale Other Cal point is already set within 5C°
Clean trolley wheels and bath Choose Cal point temperatures more than 5°C apart and recalibrate
11 Warranty information When used in laboratory conditions according to this manual, this product is guaranteed for THREE YEARS against faulty materials or workmanship. Extended warranty for years four and five can be purchased by contacting our sales department at [email protected]
LSB Aqua Pro Detailed operating manual
32138 V1 Page 28 www.grantinstruments.com
12 Maintenance and service No routine maintenance is required except for cleaning. There are no user serviceable parts inside the unit. 12.1 Cleaning Clean the outside of the equipment with a damp cloth. Domestic detergents may be used to remove stubborn dirt. To ensure free running of the trolley keep the liquid and the bath clean and free from scale. From time to time remove the tray and trolley and the drive magnet. Clean the trolley wheels and the tank where the wheels run, with warm soapy water to remove all scale and grit. Also clean the magnet and its housing. Be careful not to damage the magnet. Scale on immersed parts can also be removed using chemical de-scaling products designed for use on kitchen equipment that have metal parts. De-scaling products may be toxic and manufacturer’s instructions should always be followed. Before using any other cleaning or decontamination method, check with Grant Instruments or your local representative to make sure that the proposed method will not damage the equipment. 12.2 Fuses The fuses are internal and should not need to be replaced. 12.3 Replacing the mains cord Any replacement mains cord-set used with the water baths must meet the same specification as the one originally supplied with the unit to maintain safety of the unit and must be no more than 3m long. For Europe (including the UK), the cable must have the following markings; <HAR>, HO5VV-F 3Gx1mm2 and be rated to carry 10A. The mains plug and IEC connector must carry approvals from a European certification body (e.g. BSI, VDE or equivalent). For Australia the cable must have the following markings; HO5VV-F 3Gx1mm2 and be rated to carry 10A. The mains plug, lead and IEC connector must carry approvals from an Australian regional authority (e.g. N, NSW or equivalent). For North America 12 litre unit: the cable must have the following markings; SVT, 3x 18AWG, VW-1, 75°C, 300V,FT2 and be rated to carry 10A. The mains plug, lead and IEC connector must carry 3rd party approval marks for Canada and the US (e.g. CSA and UL marks/file numbers). 18 litre unit: the cable can only be replaced by Grant. Please contact Grant for our North American service agent’s contact details. 12.4 Routine safety tests If routine tests are to be made, we recommend a test of the integrity of the protective earth conductor and an insulation test at 500 V DC. Routine flash tests are not recommended for any electrical equipment, because repeated high voltage tests degrade insulation materials. LSB Aqua Pro Detailed operating manual
32138 V1 Page 29 www.grantinstruments.com
12.5 Service If service is required, switch off the unit and contact Grant Instruments or your local representative for repairs. Service Department Grant Instruments (Cambridge) Ltd Shepreth Cambridgeshire SG8 6GB UK Tel: +44 (0) 1763 260 811 Fax: +44 (0) 1763 262 410 E-mail: [email protected]
13 Compliance The equipment covered by this manual complies with the following EU Directives:
Machinery Directive 2006/42/EC EMC Directive 2004/108/EC RoHS Directive 2011/65/EU
Compliance has been verified by the application of the following standards:
BS EN 61326-1:2013 Electrical Equipment for measurement, control and laboratory use - EMC requirements- Part 1: General requirements
BS EN61010 Part 1:2010 Safety requirements for electrical equipment for measurement, control and laboratory use
BS EN61010 Part 2-010:2003 Safety requirements for electrical equipment for measurement, control and laboratory use. Particular requirements for laboratory equipment for the heating of material BS EN61010 Part 2-51:2003 Safety requirements for electrical equipment for measurement, control and laboratory use. Particular requirements for laboratory equipment for mixing and stirring
Additionally for 110-120V versions only:
The equipment is marked to show compliance with North American Safety Standards. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
LSB Aqua Pro Detailed operating manual
32138 V1 Page 30 www.grantinstruments.com
WEEE directive 2002/96/EC: Grant Instruments complies fully with the Waste Electrical & Electronic Equipment (WEEE) regulations 2006. We are a member of the B2B compliance scheme (Scheme Approval Number WEE/MP3338PT/SCH), which handle our WEEE obligations on our behalf. Grant Instruments have been issued with a unique registration number by the Environmental Agency, this reference number is WEE/GA0048TZ. For information regarding WEEE collections in the UK please contact our B2B Compliance Scheme directly on 01691 676 124. For other countries please contact your equipment supplier. For General WEEE information please visit: www.b2bcompliance.org.uk Battery Directive 2006/66/EC: This product does not contain any batteries.
LSB Aqua Pro Detailed operating manual
32138 V1 Page 31 www.grantinstruments.com
Grant Instruments (Cambridge) Ltd Cambridge Cambridgeshire SG8 6GB UK Tel: +44 (0) 1763 260811 Fax: +44 (0) 1763 262410 Email: [email protected] www.grantinstruments.com 32138 V1 /DMN H02 /Oct 2014