Instructions
46 Pages
Preview
Page 1
INSTRUCTIONS
HALOGEN LIGHT SOURCE
CLH-SC
Contents
Contents
HALOGEN LIGHT SOURCE CLH-SC
i
Contents
Labels and Symbols ...
1
Important Information - Please Read Before Use...
3
Intended Use ...
3
Instruction Manual ...
3
User Qualifications ...
4
Instrument Compatibility ...
4
Repair and Modification ...
4
Signal Words ...
4
Dangers, Warnings and Cautions ...
5
Chapter 1
Checking the Package Contents ...
8
Checking the Package Contents...
8
Nomenclature and Functions ...
9
2.1
Symbols and Descriptions...
9
2.2
Front Panel ...
10
2.3
Rear and Side Panels ...
10
Installation and Connection...
11
3.1
Installation ...
11
3.2
Connection to an AC Mains Power Supply ...
12
3.3
Connection to an Endoscope ...
13
3.4
Connection to an Olympus Video System...
14
Inspection...
15
4.1
Turn the Power ON ...
15
4.2
Illumination Inspection ...
18
Operation...
19
5.1
Power Supply and Illuminating the Lamp...
19
5.2
Adjusting Brightness ...
20
5.3
Video System ...
21
5.4
After Use ...
21
Lamp Replacement...
22
Lamp Replacement ...
22
Care, Storage and Disposal ...
24
7.1
Care ...
24
7.2
Storage ...
25
7.3
Disposal ...
25
1.1
Chapter 2
Chapter 3
Chapter 4
Chapter 5
Chapter 6 6.1
Chapter 7
ii
HALOGEN LIGHT SOURCE CLH-SC
Contents
Chapter 8
Troubleshooting ...
26
8.1
Troubleshooting Guide...
26
8.2
Returning the Light Source for Repair ...
27
Appendix ...
28
System Chart ...
28
Operating Environment ...
29
Transportation and Storage Environment ...
29
Specifications ...
30
EMC information ...
32
HALOGEN LIGHT SOURCE CLH-SC
iii
Contents
iv
HALOGEN LIGHT SOURCE CLH-SC
Labels and Symbols
Labels and Symbols Safety-related labels are attached to the instrument at the locations shown below. If labels are missing or illegible, contact Olympus.
Rear side
Electrical Rating Plate Lamp Rating Plate
Product name, rated-voltage, and serial number are described.
Product name and part number are described.
Symbol Mark (
)
Warns that the lamp is hot.
CE marking
Crossed-out wheeled bin’ symbol Rear Side
HALOGEN LIGHT SOURCE CLH-SC
1
Labels and Symbols
Lamp Rating Plate
Electrical Rating Plate
Back cover of this instruction manual Manufacturer
Authorized representative in the European Community
2
HALOGEN LIGHT SOURCE CLH-SC
Important Information - Please Read Before Use
Important Information - Please Read Before Use Intended Use This instrument has been designed to be used with an Olympus endoscope, Video System, accessories and other ancillary equipment for observation, diagnosis and endoscopic treatment. Do not use this instrument for any purpose other than its intended use.
Instruction Manual This instruction manual contains essential information on using this instrument safely and effectively. Before use, thoroughly review this manual and the manuals of all equipment which will be used during the procedure and use the instruments as instructed. Keep this and all related instruction manuals in a safe, accessible location. If you have any questions or comments about any information in this manual, please contact Olympus.
Terms Used in This Manual Olympus Video System Device that converts endoscopic images from a rigid endoscope or fiberscope (with rigid-scope type eyepiece) into video images on a monitor. Wall Mains Outlet An electrical outlet that has a terminal used exclusively for grounding. Isolation Transformer A safety device used to isolate non-insulated, high leakage equipment to decrease the possibility of electrical shock.
HALOGEN LIGHT SOURCE CLH-SC
3
Important Information - Please Read Before Use
User Qualifications The operator of this instrument must be a physician or medical personnel under the supervision of a physician and must have received sufficient training in clinical endoscopic technique. This manual, therefore, does not explain or discuss clinical procedures.
Instrument Compatibility Refer to the “System Chart” in the Appendix to confirm that this instrument is compatible with the ancillary equipment being used. Using incompatible equipment can result in patient injury and/or equipment damage.
Repair and Modification This instrument does not contain any user-serviceable parts. Do not disassemble, modify or attempt to repair it; patient or user injury and/or equipment damage can result. Some problems that appear to be malfunctions may be correctable by referring to Chapter 8, “Troubleshooting”. If the problem cannot be resolved using the information in Chapter 8, contact Olympus.
Signal Words The following signal words are used throughout this manual:
Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices or potential equipment damage.
4
HALOGEN LIGHT SOURCE CLH-SC
Important Information - Please Read Before Use
Indicates additional helpful information.
Dangers, Warnings and Cautions Follow the dangers, warnings and cautions given below when handling this instrument. This information is to be supplemented by the dangers, warnings and cautions given in each chapter.
•
Any applied part except “TYPE CF APPLIED PART” must never be applied directly to the heart and must not be used in procedures involving cardiac observation or surgery. Leakage current from any applied parts except “TYPE CF APPLIED PART” may be dangerous and cause ventricular fibrillation or otherwise seriously affect the cardiac function of the patient. Accordingly, always adhere to the following: Never apply the endoscope connected to any applied part except “TYPE CF APPLIED PART” to the heart or any area near the heart. Never allow an accessory or another endoscope, which is in contact with the heart (or an area near the heart) to contact the endoscope connected to any applied part except “TYPE CF APPLIED PART”. For cardiac applications, use only the instrument bearing the “TYPE CF APPLIED PART”. Only CF symbol mark “ ” bear on the applied part. Refer to the instruction manual of the camera head or light guide cable for system configuration requirements.
•
Strictly observe the following precautions. Failure to do so may place the patient and medical personnel in danger of electrical shock. When using this equipment, make sure that the metal parts of the endoscope, accessories do not come in contact with metal in the facility or with other system components. Metal-to-metal contact can create an electrical connection and cause current to flow unintentionally to the patient (leakage current, for example). Keep liquids away from all electrical equipment. If spilled fluids enter the unit, stop operation of the equipment at once and contact Olympus.
HALOGEN LIGHT SOURCE CLH-SC
5
Important Information - Please Read Before Use
Do not prepare, inspect or use this instrument with wet hands. •
The CLH-SC Light Source is not explosion-proof. Never use the Light Source in an environment containing flammable gases and liquids, or high concentrations of oxygen, and keep it away from flammable gases/liquids or sources of oxygen during use. Otherwise, explosion or fire may occur.
•
Do not touch the endoscope’s Light Guide Connector immediately after disconnecting the endoscope from this instrument. This component is extremely hot and can cause burns.
•
Do not look directly into the Distal End of the endoscope or the Output Connector of this instrument while the Light Source is illuminated. The intense light may cause eye injury.
•
It is highly desirable that a back up Light Source be available to continue clinical procedure in case of malfunction.
•
Halogen Light Sources produce significant heat due to the high intensity light required for endoscopic procedures. If the disconnected end of the Light Guide Cable and/or the Distal End of an endoscope touches operating room drapes or other flammable materials, fire may result. Never place the unattached end of an illuminated Light Guide Cable on an operating room drape or other flammable material. Never allow the Distal End of an illuminated endoscope to come in contact with operating room drapes or other flammable material. Turn the Light Source OFF whenever it is not being used.
6
•
Do not remove the cover of the Light Source. Electric shock can occur.
•
To avoid breaking electric contacts and causing a malfunction, do not apply excessive force to any connector.
HALOGEN LIGHT SOURCE CLH-SC
Important Information - Please Read Before Use
As defined by the international safety standard (IEC 60601-1: 1988), medical electrical equipment is classified into the following types: Type CF applied part (the instrument can safely be applied to any part of the body, including the heart), and Type B/BF applied part (the instrument can safely be applied to any organ except the heart). Which part of the body a videoscope or electrosurgical accessory can safely be applied to depends on the classification of the equipment to which the instruments are connected. Before beginning the procedure, review the current leakage classification type of each instrument that you will use for the procedure. Classification types are clearly specified on the instruments and in the instruments’ instruction manuals. Symbol
Classification Type CF applied part
Type BF applied part
Type B applied part
HALOGEN LIGHT SOURCE CLH-SC
7
Chapter 1 Checking the Package Contents
Chapter 1 Checking the Package Contents 1.1
Checking the Package Contents Match all items in the package with the components shown below. Inspect each item for damage. If the instrument is damaged, a component is missing or you have any questions, do not use the instrument; immediately contact Olympus.
Light Source (CLH-SC)
Power Cord
8
Instruction Manual
HALOGEN LIGHT SOURCE CLH-SC
Halogen lamp (MD-151) (Two lamps are inside the Light Source)
Chapter 2 Nomenclature and Functions
Chapter 2 Nomenclature and Functions 2.1
Symbols and Descriptions Output Connector Connector for Endoscope
Power Switch Power on Power off
Brightness Control Brightness
Decrease
Increase
Others Alternating current Fuse
HALOGEN LIGHT SOURCE CLH-SC
9
Chapter 2 Nomenclature and Functions
2.2
Front Panel Output Connector Transmits light through the endoscope or Light Guide Cable.
Power Switch Press the switch to turn the Light Source ON or OFF. The lamp inside the switch will light when the power is ON.
2.3
Brightness Control Knob Turn the Knob clockwise to increase, and counterclockwise to decrease the brightness level.
Rear and Side Panels
Fuse Box Fuses will operate in case of electrical faults.
Air Vents
Air Vents AC Inlet Side Bumpers
10
HALOGEN LIGHT SOURCE CLH-SC
Lamp Access Cover Open the cover to replace the Halogen Lamp.
Chapter 3 Installation and Connection
Chapter 3 Installation and Connection •
Turn the Light Source’s and other equipment OFF before connecting them. Otherwise, equipment damage can result.
•
To ensure proper operation of the unit, only use cables recommended by Olympus. Otherwise, equipment malfunction and/or damage may result.
•
Do not store the Light Source in a location exposed to direct sunlight, X-rays, radioactivity or strong electromagnetic radiation (near microwave medical treatment equipment, short-wave medical treatment equipment, MRI or radio equipment).
Prepare this instrument and other compatible equipment to be used with this instrument (as shown in the “System Chart” in the Appendix) before each use. Refer to the instruction manual for each piece of equipment. Install and connect all equipment described as follows:
3.1
Installation •
Do not place any equipment other than the Olympus Video System on the top of the Light Source. Otherwise, equipment damage can result.
•
Keep the Light Source’s Air Vents clear of ancillary equipment. Obstruction of the vents can cause overheating and/or equipment damage.
•
If installing on a cart, the cart must be of adequate size and strength.
Place the Light Source horizontally on stable, level surface.
HALOGEN LIGHT SOURCE CLH-SC
11
Chapter 3 Installation and Connection
3.2
Connection to an AC Mains Power Supply Connect the Power Cord directly to a Wall Mains Outlet. If the Light Source is not properly grounded, electric shock and/or fire may result.
•
Do not allow the Power Cord to become wet. A wet Power Cord may cause electric shock.
•
Make sure that the Wall Mains Outlet which is you connected to the Light Source has more capacity than the total power consumption of all connected equipment (including the Light Source). If the capacity is inadequate, fire can result or the Circuit Breaker of AC Mains Power Supply may operate and turn the Light Source and all other instrument off.
•
Do not bend, pull or twist the Power Cord. Electrical shock, equipment damage or fire can result.
The plug of the power cord that follows the equipment may vary from this drawing, as in each country the commercialized cable is in accordance to the local applicable norm.
1. Turn the Light Source OFF. 2. Connect the Power Cord to the AC Inlet on the rear panel of the Light Source and the Power Plug to a Wall Mains Outlet (see Figure 3.1). Wall Mains Outlet
Power Plug
Figure 3.1
12
HALOGEN LIGHT SOURCE CLH-SC
Inlet
Chapter 3 Installation and Connection
3.3
Connection to an Endoscope Connection to a Rigid Endoscope Connect equipment in the order described below. If connections are made in the wrong order, the light emitted from the Distal End of the Light Guide Cable may pose the following risks: It may burn you or your patient. It may ignite flammable material such as an operating room drape, which can cause a fire.
•
If the surface of the Light Guide Cable or rigid endoscope is dirty, clean it according to the directions given in the endoscope’s instruction manual before connecting it to the Light Source. If the Light Guide or endoscope is dirty, it may cause equipment damage or improper illumination.
•
Confirm that the endoscope’s Light Guide Cable Connector is dry before connecting. If the equipment is wet (after disinfection, for example), dry according to the directions given in the endoscope’s instruction manual before connecting the Light Guide Cable to the Light Source. Otherwise, equipment damage and/or improper illumination can result.
1. Connect the Light Guide Cable to the rigid endoscope. 2. Insert the Light Guide Cable Connector into the Output Connector on the front panel of the Light Source until it stops (see Figure 3.2).
Connection of a Rigid Endoscope
Figure 3.2 HALOGEN LIGHT SOURCE CLH-SC
13
Chapter 3 Installation and Connection
Connection to a Fiberscope •
If the surface of the Light Guide Cable or fiberscope is dirty, clean it according to the directions given in the endoscope’s instruction manual before connecting it to the Light Source. If the Light Guide or endoscope is dirty, it may cause equipment damage or improper illumination.
•
Confirm that the fiberscope’s Light Guide Cable Connector is dry before connecting. If the equipment is wet (after disinfection, for example), dry according to the directions given in the fiberscope’s instruction manual before connecting it to the Light Source. Otherwise, equipment damage and/or improper illumination can result.
Insert the Light Guide into the Output Connector on the front panel of the Light Source until it stops (see Figure 3.3).
Connection of Fiberscope
Figure 3.3
3.4
Connection to an Olympus Video System Refer to the instruction manuals of the rigid endoscope or fiberscope (with rigid scope type eyepiece) and the Olympus Video System (OTV-SC). Follow the instructions for video observation as described in the Olympus Video System (OTV-SC) instruction manual.
14
HALOGEN LIGHT SOURCE CLH-SC
Chapter 4 Inspection
Chapter 4 Inspection Before each case, inspect this instrument as instructed below. Inspect other equipment to be used with this instrument as instructed in their respective instruction manuals. Should the slightest irregularity be suspected, do not use the instrument and see Chapter 8, “Troubleshooting”. If the irregularity is still suspected after consulting Chapter 8, contact Olympus. Damage or irregularity may compromise the patient or user’s safety and may result in more-severe equipment damage. Prepare the instrument and other compatible equipment to be used with this instrument (shown in the “System Chart” in the Appendix) for the particular case. Refer to the respective instruction manual for each piece of equipment.
4.1
Turn the Power ON Press the upper portion of the power switch to turn the Light Source ON and confirm that power is being supplied to the equipment (see Figure 4.1). The green Power Switch will illuminate and the cooling fan will be heard.
Power Switch
Figure 4.1
HALOGEN LIGHT SOURCE CLH-SC
15