Service Manual
129 Pages
Preview
Page 1
1.0 Table of contents Golvo 7000, 7000 S/ES, 7007, 7007 S/ES Position
Ref.no.
Table of contents ... 1.0 Care and maintenance ... 2.0 Technical Specifications ... 3.0 Positions ... 4.0 Spareparts with pos.ition. ... 5.0 Base ... 1... 4.1 Mast... 2... 4.2 Middle Beam... 3... 4.3 Motorbase... 4... 4.4 Leg Protector ... 6... 4.6 Leg Protector ... 7... 4.7 Armrest... 10... 4.10 Actuator ... 11... 4.11 Emergency lowering device... 12... 4.12 Body/Handle ... 13... 4.13 Lift strap ... 14... 4.14 Lift strap ... 15... 4.15 Roll frame attachment ... 16... 4.16 Controlbox ... 18... 4.18 Attachment incl. screw ... 19... 4.19 Handcontrol ... 20... 4.20 Battery ... 21... 4.21 Cable for charging EU ... 22... 4.22 Cable for charging UK ... 23... 4.23 Cable for charging US ... 24... 4.24 Frontwheel 75 mm ... 29... 4.29 Rearwheel 100 mm ... 30... 4.30 Front wheel cover ... 31... 4.31 Rear wheel cover... 32... 4.32 Gear rack set ... 33... 4.33 End cover handle/armsupport ... 34... 4.34 End cover armrest ... 35... 4.35 Spring magazine ... 36... 4.36 Frontwheel 50 mm ... 37... 4.37 Frontwheel 100 mm ... 38... 4.38 Rearwheel 75 mm ... 39... 4.39 Rearwheel 125 mm ... 40... 4.40 Plastic housing ... 79... 4.79 Slingbar Universal 450 ... 86... 4.86 Safety latch... 87... 4.87 Electronic card tyristor ... 116... 4.116 Handcontrol 4-button ... 117... 4.117 Battery charger, EU ... 118... 4.118 Battery charger, UK ... 119... 4.119 Battery charger, US ... 120... 4.120 Battery 6,5Ah/12V ... 121... 4.121 Motor for base width adj. ... 124... 4.124 Batterybox ... 139... 4.139 Actuator G7-77 ... 140... 4.140 Electronic card processor ... 150... 4.150 Extension cable ... 160... 4.160 Troubleshooting ... 6.0 Drawings... 7.0 Checklist ... 8.0
www.liko.com
2.0 Care and Maintenance For safe and troublefree operation, there are a few routine measures which should be performed every day the lift is used. • Visually inspect the patient lift and check for external damage or wear. • Check that all screws are tight. • Check that the safety latches on the sling bar work properly. • Check the hand control and the lift and width movements. • Check the emergency lowering function. • Charge the battery every night after use, or with the frequency needed. If needed, clean the patient lift with warm water or ethanol. Warning! Do not use chemicals containing phenol or chlorine, since the aluminium parts may be damaged. Golvo should be thoroughly serviced at least once per year. Pay particular attention to parts that show wear, for example, joints, bolts, etc. Service must be carried out according to Liko service manual and by authorised staff. WARNING! Use only authorised Liko service personnel and Liko spare parts. Transportation and storage During transportation, or when the patient lift is not to be used for some time, the emergency button should be pushed in. When storing, keep the patient lift at a temperature exceeding freezing point and at a relative humidity no more than 60%. We always try to improve our products. Naturally, this means changes from time to time. Please contact our local representative or visit www.liko.com to receive the latest updates.
www.liko.com
3.0 Technical Specifications Golvo 7000/7007 Lifting speed: Motor (mast):
Motor (base): Material: Batteries: Battery charger:
2,7 cm/s 24 V = 10A/12 A. Electrical linear actuator with planetary gearing (Crown gear) and safety nut. Type GMN 3175-001. 24 V = 5 A. Geared motor. Aluminium and stainless steel Two rechargeable, valve regulated lead-acid batteries,6,5Ah - 12V Fully automatic shutdown/restart. Type HPL 40L, 230V~, 50Hz. N.A: Net voltage 120V~, 60Hz. Japan: Net voltage 100V~, 50/60Hz.
Fuses:
Battery charger T400mA Electronic card F1 T12.5A/F2 T2A Type B according to the degree of protection against electric shock. Class ll equipment.
G
D C
Capacity
L Max
Max
GOLVO 7000
150
176
202
GOLVO 7007
200
186
212
Model
A
B
C
D
E
F
G
H*
Weight
137
110
67-95
52 - 80
100
90
60
11,5
45
147
116
75-103
60-88
110
100
60
11,5
48
Min
Capacity and weight in kg. Measurement in cm. Lifting range 130 cm. Adjustable in height * Other sizes of wheels (wheels) are available on request.
Capacity
L Max
Max
GOLVO 7000
330
70
79
GOLVO 7007
440
74
83
Model
A
B
C
D
E
F
G
H*
Weight
54
43
27-38
21-32
39
35
24
4,5
99
58
46
30-41
24-35
43
39
24
4,5
106
Min
Capacity and weight in Ibs. Measurement in inches. Lifting range 130 cm (4’ 4”). Adjustable in height * Other sizes of wheels (wheels) are available on request.
Maximum Load:
Golvo 7000 150 kg (330 Ibs) Golvo 7007 200 kg (440 Ibs)
Standards:
DIN 32979 EN 60601-1 IEC 601-1 1988 SS2430
www.liko.com
3.0 Technical Specifications Golvo 7000 S/7007 S Lifting speed: Motor (mast):
Motor (base): Material: Batteries:
4,8 cm/sek, 2,7 cm/sek at max. load 24 V = 6.5A. Electrical linear actuator with planetary gearing (Crown gear) and safety nut. Manufacture by Liko. 24 V = 3.5 A. Geared motor Aluminium and stainless steel. Two rechargeable, valve regulated lead-acid batteries, 3,2 Ah - 12V
Battery charger:
Fully automatic shutdown/restart. Noratel type HPL 40L. Output 27,6V= 1.25ADC. Fuse F1: T400mA/230V T800mA/115V Specialfuses F2:pfuse F2A, F3:pfuse F2A N.A: Type HPL 40L/115, 115 V~,60 Hz Japan: Type HPL 40L/100, 100 V~,50/60 Hz Other: Type HPL 40L/230, 230 V~,50 Hz Type B according to the degree of protection against electric shock. Class ll equipment.
G
D C
Capacity
L Max
Max
GOLVO 7000S
200
176
202
GOLVO 7007S
200
186
212
Model
A
B
C
D
E
F
G
H*
Weight
137
112
67-95
52 - 80
100
90
60
11,5
43
147
116
75-103
60-88
110
100
60
11,5
48
Min
Capacity and weight in kg. Measurement in cm. Lifting range 130 cm. Adjustable in height * Other sizes of wheels (wheels) are available on request.
Capacity
L Max
Max
GOLVO 7000S
440
70
79
GOLVO 7007S
440
74
83
Model
A
B
C
D
E
F
G
H*
Weight
54
44
27-38
21-32
39
35
24
4,5
96
58
46
30-41
24-35
43
39
24
4,5
106
Min
Capacity and weight in Ibs. Measurement in inches. Lifting range 130 cm (4’ 4”). Adjustable in height * Other sizes of wheels (wheels) are available on request.
Maximum Load:
Golvo 7000S 200 kg (440 Ibs) Golvo 7007S 200 kg (440 Ibs)
Standards:
DIN 32979 EN 60601-1 IEC 601-1 1988 SS2430
www.liko.com
3.0 Technical Specifications 7000 ES/7007 ES Lifting speed: Batteries:
Battery charger: Motor (mast):
Motor (base): Charging: Wheels:
Two speeds 4.8 cm/s (with load) and 3.2 cm/s (no load) Two 2,9Ah - 12V valve regulated rechargable leadacid batteries. New batteries are supplied by the manufacturer. Built-in charger for 100-230V, 50-60 Hz, max 400 mA 24 V = 6.5 A. Manufactured by Liko with planetary gearing and safety nut (prevents damage caused due to wear) 24 V = 3.5 A. Geared motor Every night after use Standard front: 75 mm twin wheels Standard rear: 100 mm lockable single wheels. Standard wheels have a base clearance of 4 cm (1.6 inch.) Smaller and larger wheels
Material: Em. lowering: Intermittent operation:
are available as accessories. Anodized aluminium Mechanical and electrical. Int. Op 15/85, active operation max 6 min. Out of a time of 100, active must be less than 15, however not more than 6 min.
IP class 43 This device is built for indoor operation. Type B according to the degree of protection against electric shock. Class ll equipment.
G
D C
Model
Capacity
L Max
Max
A
Min
B1
B2
C
D
E
F
G
H*
Weight
Turningdiameter
GOLVO 7000 ES
200
170
199
136
53
122
67 - 95 53-81
100
90
60
11,5
43
129
GOLVO 7007 ES
200
187
209
146
56
128
75-102 62-90
110
100
60
11,5
48
138
Capacity and weight in kg. Measurement in cm. Lifting range 130 cm, adjustable. * Measure with standard wheels (75 mm front, 100 mm rear). Smaller and larger wheels are available as accessories. Capacity
L Max
Max
GOLVO 7000 ES
440
70
78
GOLVO 7007 ES
440
73.5 82
Model
A
B1
B2
53.5
21
48
57.5
22
50
Min
C
D
E
F
G
H*
Weight
Turning-
25 - 37 21-32
39
35.5
23.5
4.5
94.5
51
30 - 40 24-35
43
39
23.5
4.5
105.5
54
diameter
Capacity and weight in lbs. Measurement in inches. Lifting range 51 inches, adjustable. * Measure with standard wheels (75 mm front, 100 mm rear). Smaller and larger wheels are available as accessories.
www.liko.com
5.0
Spareparts Golvo 7000/7007, 7000 S/7007 S PART. NO
POS. NO
PRODUCT
UNIT
20090003 20090004
3 4
Middle Beam G7 Middle Beam G77
pce pce
20090046
124
Motor base with adj. G7-77 (replacement 20090005)
pce
20090038
33
Gear rack set
set
20090042 20090034 20090043
37 29 38
Frontwheel 50 mm Frontwheel 75 mm Frontwheel 100 mm
pce pce pce
20090044 20090035 20090045
39 30 40
Rearwheel 75 mm Rearwheel 100 mm Rearwheel 125 mm
pce pce pce
20090009 20090010
6 7
Leg Protector G7 Leg Protector G77
pair pair
20090013
10
Armrest complete
set
20090014 970000026
11 140
Actuator G7-77 Actuator G7-77 only
pce pce
20090015
12
Emergency lowering device
pce
20090016
13
Body/Handle set for emerg. low device
pce
www.liko.com
5.0
Spareparts Golvo 7000/7007, 7000 S/7007 S PART. NO
POS. NO
PRODUCT
UNIT
31190008
79
Plastic housing
pce
20090041
36
Spring magazine
pce
20090018 20090019
14 15
Lift strap G7 Lift strap G77
pce pce
20090020
16
Roll frame attachment G7/G77
pce
20090036
31
Front fork cover G7/G77
pair
20090037
32
Rear fork cover G7/G77
pair
X2
X2 20090039
34
End cover handle/armsupport
set
X4
20090040
35
End cover armrest
pair
X2
950000129
150
Electronic card processor
pce
950000130
116
Electronic card tyristor
pce
3692112
117
Handcontrol 4-button
pce
www.liko.com
5.0
Spareparts Golvo 7000/7007, 7000 S/7007 S PART. NO
POS. NO
PRODUCT
UNIT
3126101 3126102 3126103
118 119 120
Battery charger, EU Battery charger, UK Battery charger, US
pce pce pce
950000146
149
Battery 3,0Ah/12V G7-S
pce
950000134
121
Battery 6,5Ah/12V G7-S/G7
pce
3156001
86
Sling bar Universal 450, stainless
pce
31190018
87
Safety latch
pair
X2
www.liko.com
5.0
Spareparts Golvo 7000 ES/7007 ES PART. NO
POS. NO
PRODUCT
UNIT
20090003 20090004
3 4
Middle Beam G7 Middle Beam G77
pce pce
20090046
124
Motor for base width adj. G7-77 (replacement 20090005)
pce
20090038
33
Gear rack set
pair
20090042 20090034 20090043
37 29 38
Frontwheel 50 mm Frontwheel 75 mm Frontwheel 100 mm
pce pce pce
20090044 20090035 20090045
39 30 40
Rearwheel 75 mm Rearwheel 100 mm Rearwheel 125 mm
pce pce pce
20090009 20090010
6 7
Leg Protector G7 Leg Protector G77
pair pair
20090013
10
Armrest complete
pair
20090014
11
Actuator
pce
20090015
12
Emergency lowering device
pce
20090016
13
Body/Handle set for emerg low device
pce
www.liko.com
5.0
Spareparts Golvo 7000 ES/7007 ES PART. NO
POS. NO
PRODUCT
UNIT
31190008
79
Plastic housing
pce
20090041
36
Spring magazine
pce
20090018 20090019 20090048
14 15 185
Lift strap G7 Lift strap G77 Lift strap G77 fr o m serial no:7723630
pce pce pce
20090020
16
Roll frame attachment G7-77
pce
2006106
139
Battery box, incl. batteries
pce
20090022
18
Control box G7-77
pce
20090023
19
Attachment for control box
pce
20090024
20
Handcontrol ES 6-button
pce
20090025
21
Battery 2.9 Ah 12V
pair
3156001
86
Slingbar Universal 450, stainless
pce
31190018
87
Safety latch
pair
X2
www.liko.com
5.0
Spareparts Golvo 7000 ES/7007 ES PART. NO
POS. NO
PRODUCT
UNIT
20090026 20090027 20090028
22 23 24
Cable for charging, EU Cable for charging, UK Cable for charging, US
pce pce pce
20090036
31
Front fork cover G7-77
pair
20090037
32
Rear fork cover G7-77
pair
20090039
34
End cover handle/armsupport
set
X2
X2
X4
20090040
35
End cover armrest
pair
21090001
160
Extension cable
pce
X2
www.liko.com
4.1 Spareparts Specification
Base - 7007 Serial no.<7722427...
Version...
Part. no. 20090002 Release ...
All details according to drawing no. R 4911138-d Details Detail pos. Detail no. Wheelset 75/100 mm Golvo 2004303 Rear wheel cover 45 900000061 Front wheel cover 46 900000062 Plastic cover IKPT 2825S 50 900000066 Decal ”Liko” 900000245 Cover strip 7007 53 900000701 Rear fork 38 901011281 Front fork 39 901011282 Locking Nut M10 Nyloc 43 930000010 Nut M12 Nyloc 42 930000056
Unit 1 2 2 4 2 2 2 2 2 2
Details Detail pos. Detail no. Unit P6SS M8*45 Ezloc 44 930000060 4 Screw M6S M12*35 48 930000064 2 Screw M6S M10*35 49 930000065 2 Screw M6S M10*90 Ezloc 51 930000067 4 Washer SRKB 11*28*2 52 930000068 4 Tape-cushion 930000500 8 Base leg Golvo 7007S R 37 901011212H 1 Base leg Golvo 7007S L 37 901011212V 1 Middle beam 7007 36 20090004 1
www.liko.com
4.1 Spareparts Specification
Base - 7007 ES Serial no.>7722428...
Version...
Part. no. 20090002
Release ...
All details according to drawing no. R 4911138-d Details Detail pos. Detail no. Wheelset 75/100 mm Golvo 2004303 Rear wheel cover 45 900000061 Front wheel cover 46 900000062 Plastic cover IKPT 2825S 50 900000066 Decal ”Liko” 900000245 Cover strip 7007 53 900000701 Rear fork 38 901011281 Front forkl 39 901011282 Locking Nut M10 Nyloc 43 930000010 Nut M12 Nyloc 42 930000056
Unit 1 2 2 4 2 2 2 2 2 2
Details Detail pos. Detail no. Unit P6SS M8*45 Ezloc 44 930000060 4 Screw M6S M12*35 48 930000064 2 Screw M6S M10*35 49 930000065 2 Screw M6S M10*90 Ezloc 51 930000067 4 Washer SRKB 11*28*2 52 930000068 4 Tape-cushion 930000500 8 Base leg Golvo 7007S R 37 901011212H 1 Base leg Golvo 7007S L 37 901011212V 1 Middle beam 7007 36 20090004 1
www.liko.com
4.1.1 Assembly Instructions/Exchange
Base - 7007 ES
Note! Lock the wheels before you begin assembling the lift.
1.
1
2
Remove the mast: 1. Remove the both safety screws from the upper holes on the mast.
Start by unscrewing the transport safety plate (metal plate) at the lower edge of the mast. Save the safety plate and screws for later use if needed. 1. Place the mast on the center beam of the base, between the two black plastic caps. 2. Push the mast forward, as shown in the illustration above, until it snaps onto the center beam.
2. 2 Screw the safety screws in the lower holes on the mast. This releases the mast from the base and it can now be taken down.
When the mast is free from the base it must be supported so it does not fall.
IMPORTANT!
Secure the mast with two M6 screws (enclosed) in the upper holes on the mast. Note! Do not place any screws in the lower holes!
www.liko.com
4.2 Mast - 7000 Serial no...
Version...
Spareparts Specification
Part. no. 20090011
Release ...
All details according to drawing no. R 4911140-c Details Detail pos. Batterybox Washer TBRB 6,4*12*3 124 Emergency lowering device 70 Arm attachment 75 Attachment controlbox Motorcable Linak g G7 79 Plastic Bushing Controlbox Golvo Cover mast attachment 71 Actuator mod. Liko 69 Distance Emerg. 78 EB-Cover (alu.) 68 Pressure spring 10*10 92 Slide D=10,4 L=10,4 93 Cap IPO 12*32*1,5S 115 Handcontrol ES / Golvo Lift strap Golvo 7000S Decal serialno. Golvo 7000S Frictionplate 3,0 mm 77 Connection contact OK300 Frictionplate 3,2 mm 77 Tube Motorcable Frictionplate 3,4 mm 77 Trash Decal can - Pb Mast Decal 7000 65 Mast attachment 1 L=204 mm 66 Lift arm plastic cover 55 Distance profile L=194 mm 80 Shaft 10*74 62 Mast attachment 2 67 Decal Golvo 7000S Brace L=65 mm 73 Decal sling size Distance profile L=30 mm 76
Detail no. Unit 20090021 1 930000154 20090015 1 931891114 900000001 1 950000020 1 900000088 1 20090022 1 900000110 1 20090014 1 900000112 1 951911125 1 900000121 1 960000122 1 900000150 2 950000047 1 901311904-1 1 900000513 1 901486126-1 2 900000515 0,17 901486126-2 2 900000516 0,25 901486126-3 2 900000553 1 90191104A 1 900191106 1 900000097 1 901011241 1 900000100 1 901901118 1 900000500 2 901901123 1 900000506 1 901901143 1
Details Detail pos. Detail no. Unit Roll D=32mm 61 901486132 1 Motor attachment plate 72 901911136 1 Nylon bearing 10*15*12 60 920000048 2 MC6S M5*8 low 930000001 4 Ball bearing 6000-2Z 59 920000098 2 Locking Nut M10 Nyloc 87 930000010 2 Screw MC6S M5*12 125 930000063 1 Screw K6S M5*8 Ezloc 91 930000081 1 Screw K6S M5*8 Ezloc 57 930000081 1 Locking Nut M8 Nyloc 85 930000091 10 Screw MFX M3*10 117 930000103 1 Screw MC6S M8*22 Low 86 930000093 6 M5 Nyloc 126 930000104 1 Slingbar bracket 74 930000111 1 Sliding strip PTEF 63 900000101-1 1 Screw M6S M8*30 121 930000113 2 Cover strip 64 900000102-1 1 M6S M10*220 82 930000114 2 Frictionplate 3,0 mm 56 901486126-1 2 MC6S M8*30 Ezloc 83 930000115 2 Frictionplate 3,2 mm 56 901486126-2 2 Screw M6S M6*110 84 930000116 3 Frictionplate 3,4 mm 56 901486126-3 1 Locking Nut M6 Nyloc 118 930000117 3 Inner mast 7000 54 901891102-1 1 MC6S M5*10 Low Ezloc 88 930000118 4 Roll frame attachment 58 90191301H 1 Plastic cage D=8 mm 89 930000119 2 Roll frame attachment 58 90191301V 1 Screw MC6S M8*10 Ezloc 90 930000120 2 Decal ETL Golvo 900000336 1 MC6S M8*18 Low 120 930000153 2 Top cover IKPT 15 12 G 900000292 1 Holder for charging cable 900000324 1 www.liko.com
4.2 Spareparts Specification
Mast - 7007 Serial no...
Version...
Part. no. 20090012
Release ...
All details according to drawing no. R 4911140-c Details Detail pos. Detail no. Unit Batterybox 21 950000044 1 Screw MC6S M8*18 Low 120 930000153 2 Emergency lowering device 70 20090015 1 Washer TBRB 6,4*12*3 124 930000154 3 Attachment controlbox 900000001 1 Arm attachment 75 931891114 1 Plastic Bushing 900000088 1 Motorcable Linak g G7 79 950000020 1 Cover mast attachment 71 900000110 1 Controlbox Golvo 950000027 1 Distance Emerg. 78 900000112 1 Actuator mod. Liko 69 20090014 1 Pressure spring 10*10 92 900000121 1 EB-cover(alu.) 68 951911125 1 Cap IPO 12*32*1,5S 115 900000150 2 Glid D=10,4 L=10,4 93 960000122 1 Handcontrol ES/ Golvo 3694112ES 1 Connection contact OK300 900000515 0,2 Lift strap Golvo 7007S 901311904-2 1 Tube motorcableL=250mm 900000516 0,3 Frictionplate 3,0 mm 77 901486126-1 2 Decal serialno. Golvo 7007 ES 900000522 1 Frictionplate 3,2 mm 77 901486126-2 2 Trash Decal can - Pb 900000553 1 Frictionplate 3,4 mm 77 901486126-3 2 Mast attachment 1 L=204 mm 66 900191106 1 Mast Decal 7007 65 90191104B 1 Distance profilel L=194 mm 80 901011241 1 Lift arm plastic cover 55 900000097 1 Mast attachment 2 67 901901118 1 Shaft 10*74 62 900000100 1 Brace L=65 mm 73 901901123 1 Decal sling size 900000506 1 Distance profile L=30 mm 76 901901143 1
Details Detail pos. Detail no. Unit Decal Golvo 7007S 900000519 2 Motor attachment plate 72 901911136 1 Roll D=32mm 61 901486132 1 MC6S M5*8 low 930000001 4 Nylon bearing 10*15*12 60 920000048 2 Locking Nut M10 Nyloc 87 930000010 2 Ball bearing 6000-2Z 59 920000098 2 K6S M5*8 Ezloc 91 930000081 1 Screw MC6S M5*12 125 930000063 1 Locking Nut M8 Nyloc 85 930000091 10 Screw K6S M5*8 Ezloc 57 930000081 1 Screw MC6S M8*22 low 86 930000093 6 Screw MFX M3*10 117 930000103 1 Slingbar bracket 74 930000111 1 M5 Nyloc 126 930000104 1 Screw M6S M8*30 121 930000113 2 Sliding strip PTEF 63 900000101-2 1 M6S M10*220 82 930000114 2 Cover strip 64 900000102-2 1 MC6S M8*30 Ezloc 83 930000115 2 Frictionplate 3,0 mm 56 901486126-1 2 Screw M6S M6*110 84 930000116 3 Frictionplate 3,2 mm 56 901486126-2 2 Locking nut M6 Nyloc 118 930000117 3 Frictionplate 3,4 mm 56 901486126-3 1 MC6S M5*10 Low Ezloc 88 930000118 4 Inner mast 7007 54 901891102-2 1 Plastic cage D=8 mm 89 930000119 2 Roll frame attachment 58 90191301H 1 Screw MC6S M8*10 Ezloc 90 930000120 2 Roll frame attachment 58 90191301V 1 Decal ETL Golvo 900000336 1 Top cover IKPT 15 12 G 900000292 1 Holder for charging cable 900000324 1 www.liko.com
4.2.1 Assembly Instructions/Exchange
Mast
1.
2.
1
2
Start by unscrewing the transport safety plate (metal plate) at the lower edge of the mast. Save the safety plate and screws for later use if needed. 1) Place the mast on the center beam of the base, between the two black plastic caps. 2) Push the mast forward as shown in the illustration above, until it snaps onto the center beam.
Remove the mast: 1. Remove the both safety screws from the upper holes on the mast.
IMPORTANT!
Secure the mast with two M6 screws (enclosed) in the upper holes on the mast. Note! Do not place any screws in the lower holes!
2. Screw the safety screws in the lower holes on the mast. This releases the mast from the base and it can now be taken down.
When the mast is free from the base it must be supported so it does not fall.
www.liko.com
4.3 Spareparts Specification
Middle Beam- 7000 ES Serial no. < 7021493
Version...
Part. no. 20090003
Release ...
All details according to drawing no. R 4911135-2 Details Detail pos. Detail no. Unit Plastic Bushing 29 900000088 1 Sign decal 900000502 1 Measurement 900000504 1 Pedal slip joint 14 901901127 2 Flanged slide bearing 12*15*5 17 920000075 2 Flanged slide bearing 10*12*6 24 920000082 3 Nylon bearing15*18*5 122 921921150 1 Clamp ring SGA 12 16 930000074 2 Woodruff WK 3*13 18 930000076 2 Screw K6S M6*10 Ezloc 21 930000079 1 MRX M4*10 25 930000083 1 M4 Nyloc 128 930000084 1 Woodruff key 6*28*2 26 930000085 1 Washer PVC 10*16*2 27 930000086 1 Screw K6S M8*60 31 930000090 4 Locking Nut M8 Nyloc 32 930000091 9 Screw K6S M8*16 33 930000092 1 Screw MC6S M8*22 Low 34 930000093 4 Gearwheel 14 M2 9 961111352 1 Beam plastic cover R 15 900000730H 1 Beam plastic cover L 15 900000730V 1 Cover profil 4 901011242-1 2 Middle beam 7000 1 9011119DA 1 Gearwheel 7000 2 9011120BA 2 Frictionplate 3,0 mm 35 901486126-1 8 Frictionplate 3,2 mm 35 901486126-2 8 Frictionplate 3,4 mm 35 901486126-3 8
Details Gear rack Gear rack Slipper Base motor hood Baser motor hood, lower Screw K6S M5*8 Ezloc Plastic Bushing Woodruff key 6*28*2 Washer PVC 10*16*2 Motor attachment 2 Screw M6S M6*20 Franged slide bearing RXS B6*13 Plastic bearing BRB 5,3*10*1 Nylon bearing 15*18*5 Support ring Camp ring SGA 12 Shaft 12*177 Woodruff WK 3*13 Motor SWMF Screw MRX M4*12 Screw MRX M4*5 Motorcable Linak u-rede Damper 12*140 Gearwheel 60 M1 Gearwheel 20 M1
Detail pos. Detail no. Unit 11 90181701-1 1 130 90181701-2 1 10 90181701-3 1 13 900000072 1 127 900000094 1 23 930000081 2 29 900000088 1 26 930000085 1 27 930000086 2 3 90101130B 1 28 930000087 3 17 920000075 2 129 930000096 3 8 921911134 1 930000164 1 122 921921150 1 930000400 1 16 930000074 2 5 931911133 1 18 930000076 4 6 940000071 1 19 930000077 1 22 930000080 1 30 950000031 1 20 930000078 1 7 961111351 1 12 961111353 1 www.liko.com
4.3 Spareparts Specification
Middle Beam - 7000 ES Serial no. > 7021494
Version...
Part. no. 20090003
Release ...
All details according to drawing no. R 4991101-3/ R 4911135-2 Details Detail pos. Detail no. Unit Plastic Bushing 20 900000088 1 Sign decal 900000502 1 Measurement 900000504 1 Pedal slip joint 14 901901127 2 Flanged slide bearing 12*15*5 3 920000075 2 Flanged slide bearing 10*12*6 4 920000082 3 Nylon bearing 15*18*5 5 921921150 1 Clamp ring SGA 12 17 930000074 2 Woodruff WK 3*13 9 930000076 2 Screw K6S M6*10 Ezloc 21 930000079 1 MRX M4*10 25 930000083 1 M4 Nyloc 128 930000084 1 Woodruff key 6*28*2 21 930000085 1 Washer PVC 10*16*2 7 930000086 1 Screw K6S M8*60 31 930000090 4 Locking Nut M8 Nyloc 32 930000091 9 Screw K6S M8*16 33 930000092 1 Screw MC6S M8*22 Low 34 930000093 4 BRB 5,3*10*1 930000164 2 Gearwheel 14 M2 9 961111352 1 Beam plastic cover Right 15 900000730H 1 Beam plastic cover Left 15 900000730V 1 Cover profil 4 901011242-1 2 Middle beam 7000 1 9011119DA 1
Details Detail pos. Detail no. Unit Gearwheel 7000 2 9011120BA 2 Frictionplate 3,0 mm 35 901486126-1 8 Frictionplate 3,2 mm 35 901486126-2 8 Frictionplate 3,4 mm 35 901486126-3 8 Gear rack 11 90181701-1 1 Gear rack 130 90181701-2 1 Slipper 10 90181701-3 1 Damper BumpOn black 900000159 2 Motor attachment 3 G7-77 1 901811972 1 Motor ITT S404156 G7-77 2 940000004 1 Gearwheel 20M1 mod.2 G7-77 6 901113543 1 Gearwheel 60M1 mod.2 G7-77 12 901113541 1 Shaft 12x181 G7-77 8 901111332 1 Bearing u-carriage mod.2 G7-77 11 901111342 1 Middle axle 10x46,7 G7-77 13 901971198 1 Stepped spur gear 20/44M1 G7-77 14 901981199 1 Screw MC6S TT M5x12 15 930000234 3 Clamp ring SGA 10 16 930000250 2 Motor hood u-carriage G7-77 18 900000390 1 Screw MRX M5x90 19 930000240 2 Motorcable G7-77 22 950000054 1 Damper BumpOn SJ5018 23 900000391 4 Flat key 3x3x25 SMS2306 24 930000243 1 Spacer PS 12x18x1 25 930000251 1 www.liko.com
4.3 Spareparts Specification
Middle Beam - 7007 ES Serial no. < 772427
Version...
Part. no. 20090004
Release ...
All details according to drawing no. R 4911135-2 Details Detail pos. Detail no. Unit Base motor hood 13 900000072 1 Screw K6S M8*16 33 930000092 1 Plastic Bushing 29 900000088 1 Screw MC6S M8*22 Low 34 930000093 4 Base motor hood, lower 127 900000094 1 Screw RXS B6*13 129 930000096 3 Sign decal 900000502 1 BRB 5,3*10*1 930000164 1 Measurement 900000521 1 Support ring SS 13*19*1,5 930000400 1 Pedal slip joint 14 901901127 2 Shaft 12*177 5 931911133 1 Flanged slide bearing 12*15*5 17 920000075 2 Flanged slide bearing 10*12*6 24 920000082 1 Motor SWMF 6 940000071 1 Motorcable Linak u-carriage grey 30 950000031 1 Plastic bearing 8 921911134 1 Nylon bearing 5*18*5 122 921921150 1 Gearwheel 60 M1 7 961111351 1 Gearwheel 14 M2 9 961111352 1 Gearwheel 20 M1 12 961111353 1 Clamp ring SGA 12 16 930000074 2 Woodruff WK 3*13 18 930000076 4 Beam plastic cover Right 15 900000730H 1
Details Beam plastic cover Left Screw MRX M4*12 Damper 12*140 Cover profil 7000 Screw K6S M6*10 Ezloc Screw K6S M5*8 Ezloc Motor attachment 2 Screw MRX M4*5 MRX M4*10 Middle Beam 7007 Gearwheel 7007 Frictionplate 3,0 mm Frictionplate 3,2 mm Frictionplate 3,4 mm M4 Nyloc Woodruff key 6*28*2 Washer PVC 10*16*2 Gear rack Gear rack Screw M6S M6*20 Screw K6S M8*60 Slipper Locking Nut M8 Nyloc Damper BumpOn black
Detail pos. Detail no. Unit 15 900000730V 1 19 930000077 1 20 930000078 1 4 901011242-1 2 21 930000079 1 23 930000081 2 3 90101130B 1 22 930000080 1 25 930000083 1 1 9011119DB 1 2 9011120BB 2 35 901486126-1 8 35 901486126-2 8 35 901486126-3 8 128 930000084 1 26 930000085 1 27 930000086 2 11 90181701-1 1 130 90181701-2 1 28 930000087 3 31 930000090 4 10 90181701-3 1 32 930000091 9 900000159 2 www.liko.com