LCexv 4010 MediLine Combination Refrigerator Freezer Operating Instructions

Content

Priority of warnings... 14 Safety instructions and warnings... 14 Symbols on the appliance... 15 Intended use... 15 Foreseeable incorrect use... 15 Declaration of conformity... 15 Climate rating... 16 Noise emissions from the appliance... 16 Description of the appliance... 16 Setting up... 16 Levelling the appliance... 16 Electrical connection... 16 Safety lock... 16 Operating and control elements... 17 Switching the appliance on and off... 17 Setting the temperature... 17 Temperatur display mode... 17 Door open alarm... 18 Setting the delay time for the door open alarm... 18 Audible warning signal settings... 18 Deactivating the audible warning signal function... 18 Alarm test... 18 Alarm messages... 19 Adjusting the alarm parameters... 19 Calling up stored alarm events and reading the temperature progression... 19 Resetting the stored alarm events HAn... 19 Resetting the recorded temperature progression rt ... 19 Example of an alarm query...20 Calibrating the control sensor...20 Product sensor (available accessory)...20 Calibrating the product sensor ...20 Switching the temperature display between control sensor and product sensor...20 Keypad lock... 21 Changing the network address ... 21 Resetting the parameters to factory settings... 21 Setting the real time clock... 21 Conversion from summer to winter time... 21 Enabling/disabling automatic conversion from summer to winter time... 21 Cleaning...22 Shutting your appliance down...22 Disposal notes...22 Malfunctions...23 Possible error messages in the display...23 External alarm...23 Opening for external temperature sensor... 24 Changing over door hinges...24

Priority of warnings DANGER

identifies a situation involving direct danger which, if not obviated, may result in death or severe bodily injury.

WARNING

identifies a dangerous situation which, if not obviated, may result in death or severe bodily injury.

CAUTION

identifies a dangerous situation which, if not obviated, may result in minor or medium bodily injury.

NOTICE

identifies a dangerous situation which, if not obviated, may result in damage to property.

Note

identifies useful information and tips.

Safety instructions and warnings

- WARNING: do not seal ventilation openings on the appliance housing or enclosure.

- WARNING: only use the mechanical devices or other aids recommended by the manufacturer to help speed up the defrosting process. - WARNING: do not damage the refrigerant circuit.

- WARNING: do not use any electrical devices in the refrigerator compartment which do not comply with the design recommended by the manufacturer.

- WARNING: the mains cable must not be damaged while installing the appliance. - WARNING: multi-sockets or distributor strips and other electronic devices (such as halogen transformers) must not be positioned and operated at the rear of appliances. - WARNING: this appliance must be secured as described in the operating instructions to rule out any potential risks due to its instability.

- This appliance can be used by children of 8 years old and over, and also by persons with restricted physical, sensory or mental capacity or lack of experience and knowledge, if they are supervised or have been instructed on safe use of the appliance and understand the resulting risks. Children must not be allowed to play with the appliance. Cleaning and user maintenance must not be carried out by children without supervision.

14

- To prevent injury and damage to property, the appliance should only be installed by two people.

- After unpacking it, check the appliance for signs of damage. Contact the supplier if it is damaged. Do not connect the appliance to the mains power supply. - Avoid prolonged skin contact with cold surfaces (e.g. chilled/frozen products). If necessary, take safety action (e.g. gloves). - All repairs and work on the appliance may only be carried out by customer service personnel or other trained personnel. The same applies to changing the mains power cable.

- Only carry out repair and other work on the appliance when the mains plug has visibly been disconnected. - Only install, connect and dispose of the appliance as described in these operating instructions.

- In the event of a fault, pull out the plug or switch off the fuse. - When disconnecting the appliance from the mains, pull on the plug. Do not pull on the cable. - Do not allow naked flames or ignition sources to enter the appliance. WARNING Danger of sparks produced by friction due to dust on the fan blades. Do not store dusty objects in the appliance. Clean the ventilation slots on the recirculated air fan every month using a vacuum cleaner.

Symbols on the appliance

EN

The symbol can be located on the compressor. It refers to the oil in the compressor and indicates the following danger: swallowing or inhaling can be fatal. This is only relevant for recycling. There is no danger in normal operation. Warning about inflammable substances.

A sticker to this effect may be applied to the rear of the appliance. It refers to the foampadded panels in the door and/or the housing. This is only relevant for recycling. Do not remove the sticker.

Intended use

This appliance has an interior free of ignition sources for professional use and is suitable for storing highly inflammable products in sealed containers at temperatures between 3°C and 16°C (refrigerator compartment), -9°C and -30°C (freezer compartment). The interior is licensed as a Zone 2 hazardous area under 2014/34/ EU (ATEX Directive). Typical products for storage include research samples, reagents, laboratory inventory, etc. which are classed in explosion group IIB+H2 and temperature class T6 under 2014/34/EU (ATEX Directive). The explosion group is shown on the safety data sheet of the product for storage. If you are uncertain, contact the supplier of the product. For the storage of valuable or temperature-sensitive substances or products the use of an independent, constantly monitoring alarm system is necessary. This alarm system must be designed so that each alarm status is detected immediately by an authorised person who can then take appropriate action.

Foreseeable incorrect use Do not use the appliance for the following applications:

• Storage and cooling of - chemically unstable - blood, plasma or other bodily fluids for the purposes of infusion, application or insertion into the human body. • Use in potentially explosive atmospheres.

• Use outdoors or in areas where it is exposed to splash water or damp conditions. Incorrect use of the appliance will result in damaging or spoiling the goods stored in it.

Declaration of conformity

The refrigerant circuit has been tested for leaks. The appliance complies with the relevant safety regulations and EU Directives 2006/42/EG, 2014/30/EU, 2009/125/EG and 2011/65/EU.

15

Climate rating

Setting up

The climate rating indicates at what room temperature the appliance may be operated to achieve full cooling capacity and what the maximum humidity level in the area around the appliance may be to ensure that no condensation forms on the exterior housing.

• Do not place the appliance in direct sunlight or near radiators and similar sources of heat.

The climate rating is indicated on the type plate.

• Always install the appliance directly against the wall.

• The more coolant there is in the appliance, the larger the room in which the appliance is installed must be. If the room is too small, any leak may create a flammable mixture of gas and air. For each 8 g of coolant the installation space must be at least 1 m³. Information on the coolant is on the model plate inside the appliance.

Max. room temperature

Max. relative humidity

4

30 °C

55%

Compensate floor unevenness using the adjustable feet.

7

35 °C

75%

NOTICE

Climate rating 3

5

25 °C

40 °C

60% 40%

The minimum room temperature at the place of installation is 10°C.

Description of the appliance (1) Operating and control elements (2) Type plate (3) Adjustable shelves (4) Defrost water collection tray

Levelling the appliance

The appliance must be aligned horizontally and vertically. If the appliance is not level, the main body of the appliance can be deformed and the door will not close properly.

Appliance dimensions

(5) Drawers (6) Adjustable-height feet

NOTICE

The maximum load per shelf is 40 kg.

The maximum load per drawer is 20 kg.

Noise emissions from the appliance

The noise level while the appliance is operating is below 70 dB(A) (relative noise level 1 pW).

Electrical connection

Only operate the appliance with alternating current (AC). The permissible voltage and frequency are indicated on the type plate. The position of the type plate is shown in the section entitled Description of the appliance. The socket must be properly earthed and protected by a fuse. The tripping current of the fuse must be between 10 A and 16 A.

Other features

The socket must not be situated behind the appliance and must be easily accessible.

- Audible and visual door open alarm.

Do not connect the appliance using an extension cable or extension socket.

- Serial interface (RS485) for external temperature and alarm documentation.

Do not use stand-alone inverters (conversion of direct current to alternating current/threephase current) or energy-saving plugs. Risk of damage to the electronic control system!

- Audible and visual temperature alarm. - Floating contact for connection to a remote monitoring system.

- Maximum/minimum interior temperatures are stored.

- Last 3 temperature alarms are saved with time, date and duration of alarm.

- Last 3 power cuts are saved with time, date and duration of power cut. - Safety thermostat to avoid temperatures below +2°C.

It is essential to use these safety facilities to avoid damage to stored items. These facilities must not be deactivated or decommissioned!

Safety lock

The lock in the appliance door is equipped with a safety mechanism.

Locking the appliance

• Insert the key as shown by arrow 1. • Turn the key by 90°. To unlock the appliance, the same procedure must be repeated in the same order.

16

EN

Operating and control elements

freezer

refrigerator

General description

Time or temperature information that appears after the word ­ isplay = are sample values. D The following sections explain how the refrigerator compartment is operated. Operation of the freezer compartment is identical to this.

Symbols in the display Compressor is running LED flashing - refrigeration unit switches on after a delay. The compressor will start automatically after the pressure in the refrigerant circuit has equalised. Fan is running

On/Off button (switching the appliance on and off) Selection buttons Keypad lock Button for calling up stored alarm events Audible alarm Off button Enter button

Appliance is defrosting Temperature display via product sensor is activated LED flashing and appears in the display. The real time clock must be reset. The display means that the power supply and interior temperature of the appliance are recorded. If flashes in the display, there has either been a power failure or the temperature in the appliance exceeded the permissible range. Alarm function The appliance has suffered a fault. Contact the customer service department.

Switching the appliance on and off

Setting the temperature

Connect the appliance to the mains. Display = OFF.

Press

Switching the appliance on

To increase the temperature (warmer): press button

Press

for approx. 5 seconds - Display = ON.

No alarm is displayed or sounded when the appliance is switched on for the first time. If the appliance is disconnected from the mains for a long time after it has been switched on for the first time and if the temperature inside the appliance rises above the upper alarm limit, this will be detected as a fault by the electronic control system ( appears in the display). When the appliance is switched on again, this display must be reset as shown below. Press

.

Press

+

The

LED will now light up permanently.

Press

for 5 seconds.

for 5 seconds. Display =

The electronic control system will switch back to normal operating mode.

Switching the appliance off Press

for approx. 5 seconds - Display =

for 1 second. The temperature display flashes.

To reduce the temperature (colder): press button Press

. .

again.

The desired temperature setting is saved.

Note

The temperature in the warmest area of the interior may be higher than the temperature setting. If the door is left open for a lengthy period, the temperature in the appliance's compartments may rise dramatically.

Temperatur display mode

The temperature display can be switched between degrees Celsius and degrees Fahrenheit. Factory setting is degrees Celsius. Press

for 5 seconds. Display =

Press

. Display =

Use button

or

0 = °C

1 = °F

Press

. Display =

to select the desired setting.

Press for 5 seconds. The electronic control system will switch back to normal operating mode. 17

Door open alarm

When the door is opened, the LED display begins to flash.

lights up and the temperature

When the door has been left open for more than 60 seconds, the LED begins to flash, and and the temperature indication flash alternately in the display. The audible warning signal sounds (unless the audible warning signal function has been deactivated). If the door has to stay open for longer in order to insert items to be cooled, cancel the audible warning signal by pressing button .

Setting the delay time for the door open alarm

The time before the audible warning signal sounds after the door has been opened can be adjusted. Press

for 5 seconds. Display =

Press

until

Press

. Display =

Use button

appears in the display.

or

Setting range = 1 - 5 minutes. to select the desired setting.

Press

. Display =

Press

for 5 seconds.

The audible warning signal function can be completely deactivated if necessary. Press

for 5 seconds. Display =

Press

until

Press

. Display =

Use button

appears in the display. or

to select the desired setting.

0 = audible warning signal function activated 1 = audible warning signal function deactivated Press

. Display =

Press

for 5 seconds.

The electronic control system will switch back to normal operating mode.

Alarm test

This test checks the function of the internal and any external connected alarm device. The appliance does not stop its refrigerating function during this test.

The electronic control system will switch back to normal operating mode.

Audible warning signal settings

Press

+

for 5 seconds.

• The display will change to a temperature value of 0.2°C below the set upper alarm limit. • The temperature value will now rise by 0.1°C every 2 seconds.

The audible warning signal will be muted for the current alarm after the button has been pressed. Complete the following steps if you want the audible warning signal to reactivate automatically.

• When the upper alarm limit is reached,

Press

for 5 seconds. Display =

Press

until

• The temperature value will continue to rise up to 0.2°C above the upper alarm limit.

Press

. Display =

Press

. Display =

Press

. Display =

appears in the display.

will appear in the

display. An external alarm unit connected to the floating alarm output will now be activated.

• The same process will take place automatically for the lower alarm limit.

The LED

will appear in the display.

will be lit during the test.

Automatic reactivation of the audible warning signal is now active.

The electronic control system will switch back to normal operating mode.

The time before the audible warning signal sounds again must be set.

Cancelling the test prematurely

Press

. Display =

Press

Press

. Display =

Use button

or

Setting range = 1 - 120 minutes.

to select the desired setting.

Press

. Display =

Press

for 5 seconds.

The electronic control system will switch back to normal operating mode.

18

Deactivating the audible warning signal function

for 5 seconds.

Note If the values of the upper and lower alarm limit (AL and AH in the section entitled "Adjusting the alarm parameters") are set to 0, and will appear in the display during this test. Note For a realistic temperature alarm test, an additional delay time (60 minutes) applies as well as the adjustable alarm parameters AL, AH and Ad. After a door has been opened or a defrosting process, the alarm delay Ad will be extended by an additional delay time (60 minutes). This additional delay time must not be changed. This means that a temperature alarm will appear later after a door has been opened or a defrosting process than is actually set using parameter Ad.

Alarm messages

1. LED

flashes in the display

If appears in the display, the appliance has a fault. Consult your nearest customer service point. 2. LED

EN

Calling up stored alarm events and reading the temperature progression Press

Scroll through the list using

The interior is too warm (HI) or too cold (LO).

Last temperature alarm but one Temperature alarm before

Note The alarm parameters can be adjusted. See Adjusting the alarm parameters.

Number of power cuts Last power cut

flashes in the display

Last power cut but one

There has been a power cut (HF) of some length or the interior was too warm or too cold (HA) during a certain period of time.

Power cut before

Up to three alarm events can be stored and called up.

Period in hours in which the maximum and minimum interior temperatures were measured

Adjusting the alarm parameters

Note After a door has been opened or a defrosting process, the alarm delay Ad will be extended by an additional delay time (60 minutes). This additional delay time must not be changed. This means that a temperature alarm will appear later after a door has been opened or a defrosting process than is actually set using parameter Ad. Press

for 5 seconds. Display =

Press

until

appears in the display.

= Lower alarm limit Press

. Display = temperature difference in °C

Use button

or

to select the desired setting.

Set positive values only. Press

. Display =

Press

. Display =

Press

. Display = temperature difference in °C

Use button

or

Upper alarm limit

to select the desired setting.

.

Last temperature alarm

The audible warning signal sounds (unless the audible warning signal function has been deactivated).

The alarm limits (difference to the set temperature) and the alarm delay (delay until alarm sounds) can be adjusted.

or

Number of temperature alarms

flashes in the display; the display reads HI or LO

3. HA / HF /

. Display =

Maximum (highest) measured temperature Lowest measured temperature Select the required item using the again to return to the list.

button. Press this button

You can exit the menu at any time by pressing

for 5 seconds.

If no button is pressed within 60 seconds, the electronic control system switches back automatically.

Resetting the stored alarm events HAn Press

. Display =

Press

+

Press

for 5 seconds.

for 5 seconds. Display =

.

The electronic control system will switch back to normal operating mode.

Resetting the recorded temperature progression rt Press

. Display =

Press the button

or

until

appears in the display.

Set positive values only.

Press

. Display =

Press

. Display =

Press

for 5 seconds. Display =

Press

. Display =

Press

. Display = alarm delay in minutes

The values for and (highest and lowest measured interior temperature) are then reset to the current interior temperature.

Use button

or

to select the desired setting.

Press

. Display =

Press

for 5 seconds.

Press

.

for 5 seconds.

The electronic control system will switch back to normal operating mode.

The electronic control system will switch back to normal operating mode. 19

Example of an alarm query Situation: HA/HF/

flashes in the display.

Press

. Display=

Press

. Display =

The temperature may be measured or recorded at any point in the interior using the product sensor.

• Connect sensor (see section entitled External alarm)

There has not been an alarm status with a too high or too low temperature. You must switch to display . Press

. Display =

Press

until

Press

. Display = 1 power failure has occurred.

Press

. Display =

Press

. Display =

Press

. Display =

(year)

Press

. Display =

(month 1-12)

Press

. Display =

(day 1-31)

Press

. Display =

(hour 0-23)

Press

. Display =

(minute 0-59)

Press

. Display =

(period of time in hours)

Press

+

The

LED will now light up permanently.

appears in the display.

Last power failure.

for 5 seconds. Display =

HA/HF is cancelled in the display. The electronic control system is now ready for the next alarm. Press

Product sensor (available accessory)

for 5 seconds.

The electronic control system will switch back to normal operating mode.

Calibrating the control sensor

(standard sensor for temperature control)

Possible tolerances of the control sensor (the displayed temperature compared to the actual interior temperature) can be offset with this function.

Press

for 5 seconds. Display =

Press

until

Press

. Display = correction value set at the factory

appears in the display.

Use button or to increase or decrease the correction value in 0.1°C increments. Press

. Display = actual (corrected) interior temperature

Press

. Display =

Press

for 5 seconds.

The electronic control system will switch back to normal operating mode.

Activating the sensor

Press

for 5 seconds. Display =

Press

. Display =

Press

. Display =

Press

. Display =

Press

. Display =

Press

for 5 seconds.

The electronic control system will switch back to normal operating mode. If appears in the display, the product sensor has not been activated. If appears in the display, the product sensor has not been connected, or is faulty.

Calibrating the product sensor

Possible tolerances of the product sensor (the displayed temperature compared to the actual interior temperature) can be offset with this function. Press

for 5 seconds. Display =

Press

until

Press

. Display =

appears in the display.

Use button or to increase or decrease the correction value in 0.1°C increments. Press

. Display = actual (corrected) product sensor temperature

Press

. Display =

Press

for 5 seconds.

The electronic control system will switch back to normal operating mode.

Switching the temperature display between control sensor and product sensor

Press

for 5 seconds. Display =

Press

until

Press

. Display = (control sensor)

Press

. Display =

appears in the display.

(product sensor)

If the product sensor is activated, Press

. Display =

Press

for 5 seconds.

appears in the display.

The electronic control system will switch back to normal operating mode.

20

Keypad lock

The keypad lock ensures that no unintentional changes are made to the electronic control system.

Setting a PIN code for the keypad lock function Press

for 5 seconds. Display =

Press

until

Press

. Display =

Use button

appears in the display. or

to choose a PIN code between 1 and 999.

Setting the real time clock

The real time clock is preset (CET). For a different time zone, the time must be adjusted manuall. Press

for 5 seconds. Display =

Press

. Display =

Press

. Display =

Press

. Display = . Display =

Press for 5 seconds. The electronic control system will switch back to normal operating mode.

Press

. Display =

Activating the keypad lock

Press

. Display =

Press

. Display =

Press

. Display =

for 5 seconds. Display =

Use button Press

or

to select the PIN code.

. Display =

All buttons except

and

are locked.

. Display =

Press

. Display =

to select the PIN code.

(day 1-31)

Set the hour by pressing the

All functions are enabled.

Press

. Display =

If an incorrect PIN code is entered, the keypad lock remains active.

Set the minutes by pressing the

Changing the network address

.

buttons. Press

buttons. Press

.

(minute 0-59) buttons. Press

.

for 5 seconds. The electronic control system will switch Press back to normal operating mode. appears in the display, the real time clock must be

When connecting several appliances via the RS485 interface, each appliance must have its own network address.

When reset.

Press

for 5 seconds. Display =

Press

until

Conversion from summer to winter time

Press

. Display =

Use button Press

appears in the display.

or

to change the network address (1-207).

. Display =

Press for 5 seconds. The electronic control system will switch back to normal operating mode.

Resetting the parameters to factory settings

Conversion to summer time is carried out automatically by the electronic control system on the last Sunday in March at 2 o’clock in the morning.

Conversion to winter time is carried out automatically by the electronic control system on the last Sunday in October at 2 o’clock in the morning.

In order to enable the new time, the appliance must be switched off and on after each of the times specified above.

Enabling/disabling automatic conversion from summer to winter time

The alarm limits and sensor calibration values can be reset to the factory settings using this function.

Press

for 5 seconds. Display =

Pull out the mains plug.

Press

until

Press

. Display =

Keep

pressed and connect the mains plug.

Use button

appears in the display. or

Display =

0 = deactivated

Press

Press

. Display =

The electronic control system will switch back to normal operating mode.

.

(hour 0-23)

. Display =

. Display =

buttons. Press

Set the day of the week by pressing the

Press

Press

.

. Display =

Press

or

buttons. Press

. Display = (days of the week) Press (1 = Monday, 7 = Sunday)

Deactivating the keypad lock Use button

.

(month 1-12)

Set the day by pressing the

Press

for 5 seconds. Display =

buttons. Press

Set the month by pressing the

If an incorrect PIN code is entered, the electronic control system switches back to normal operation without activating the keypad lock.

Press

(year)

Set the year by pressing the Press

Press

EN

to select the desired setting. 1 = activated

. Display =

Press for 5 seconds. The electronic control system will switch back to normal operating mode.

21

Cleaning

WARNING Before cleaning, always disconnect the appliance from the mains. Pull out the plug or switch off the fuse. WARNING Risk of electrostatic discharge. Only clean plastic parts with a damp cloth! CAUTION Risk of damage to the appliance components and risk of injury due to hot steam.

Defrosting

Refrigerator compartment

The refrigerator compartment defrosts automatically.

1 The defrost water

drains into a tray situated below the evaporator. This tray must be emptied from time to time.

Pull the tray out towards you and empty.

2 To avoid having to

empty the defrost water collection tray frequently, you can place a container under the drain opening in the tray.

The defrost water collection tray may only be inserted on the lowest support rib.

Do not use steam cleaning equipment to clean the appliance.

Freezer compartment

NOTICE All surfaces in the appliance must be cleaned at regular intervals!

• To defrost, switch the appliance off.

• Clean the inside, equipment parts and outer walls with lukewarm water and a little detergent. Do not use chemical solvents or any cleaning agents containing sand or acid. • To avoid short-circuits, ensure no cleaning water penetrates into the electrical components when cleaning the appliance. • Dry all parts well with a cloth. • The dust should be removed from the refrigeration unit and heat exchanger - metal grid at the back of the appliance - once a year. • Do not damage or remove the type plate on the inside of the appliance. It is very important for servicing purposes.

After the appliance has been in operation for some time, a layer of frost or ice will form on the inside walls. This increases energy consumption. You should therefore defrost the appliance regularly.

• Remove the drawers.

• Transfer items to other appliances.

• Leave the door of the appliance open while defrosting. After defrosting mop up the remaining water with a cloth and clean the appliance.

Shutting your appliance down

If the appliance is left empty for a lengthy period, it must be switched off, defrosted, cleaned and dried and the door is to be left open to prevent mould formation.

Disposal notes

The appliance contains reusable materials and should be disposed of properly - not simply with unsorted household refuse. Appliances which are no longer needed must be disposed of in a professional and appropriate way, in accordance with the current local regulations and laws. Do not damage the refrigerant circuit of an appliance that is no longer needed during its disposal. This appliance contains inflammable gases in the refrigerant circuit and insulation foam. Your local council or a waste disposal contractor can provide information about how to dispose of the appliance correctly.

22

Malfunctions

You may be able to rectify the following faults by checking the possible causes yourself: • Appliance does not function: – Is the appliance switched on? – Is the plug correctly fitted in the mains socket? – Is the fuse intact? • The temperature is not low enough: – Is the temperature setting correct (see "Setting the temperature")? – Does the separately installed thermometer show the correct reading? – Is the ventilation system working properly? – Is the appliance set up too close to a heat source?

EN

External alarm

There are various connection options at the back of the appliance.

The appliance may only be connected to an external alarm device by trained personnel.

Note The connectors are secured with screws. To remove the connectors, undo the left and right screws.

• Temperature alarm test does not work as required. – See „Alarm test“ and „Adjusting the alarm parameters“ If none of the above causes apply and you cannot rectify the fault yourself, contact the nearest customer service department stating the type designation 1, service number 2 and appliance number 3as indicated on the type plate.

Floating alarm output Connection to RS485 interface

The position of the type plate is shown in the section entitled Description of the appliance.

Possible error messages in the display Error code

E0, E1, E2, rE EE, EF dOr HI

LO Etc HF, HA

AFr

Error

Action

Temperature sensor defective

Contact the customer service department

Electronic control system error

Contact the customer service department

Temperature inside appliance too high (too warm)

Check that the door has been closed properly. If the temperature does not drop, contact the customer service department.

Appliance door open for too long

Close appliance door

Optional temperature sensor connection (freezer compartment) Optional temperature sensor connection (refrigerator compartment)

Floating alarm output

These three contacts can be used to connect the appliance to an optical or acoustic alarm device. The connection is designed for a maximum of 42 V/8 A DC from a safety extra-low voltage (SELV) source (minimum current: 150 mA).

Notice

When supplying mains voltage to the floating alarm contact, the technical safety requirements of standard EN 60335 will not be satisfied.

N.O

Connection for a visual warning light or an acoustic alarm signal.

N.C

Temperature inside appliance too low (too cold)

Contact the customer service department

Connection for a control lamp to indicate that the appliance is in normal mode.

COM

There has been a power cut of some length or the interior was too warm or too cold during a certain period of time.

Reset the real time clock (see "Setting the real time clock")

See Calling up stored alarm events and reading the temperature progression

Temperature around Contact the customer the product sensor service department < 0°C

External power supply unit, 42 V/8 A DC maximum, Minimum current: 150 mA

RS485 interface Rx- / Tx- Send/Receive data cable

(negative pole)

Rx+ / Tx+ Send/Receive data cable (positive pole) GND Earth cable 23

Opening for external temperature sensor

Changing over door hinges Door hinges should only be changed by a trained expert. Changing the door hinges must be done by two people.

Sensor cable opening for refrigerator compartment

1. Unscrew the lower hinge brackSensor cable opening for freezer compartment

Sensor cable opening for refrigerator compartment Drill marked section on the back of the appliance.

et.

Important: the door mounting has a spring mechanism enabling the door to close by itself. The hinge bracket turns to the left when the screws are undone.

2. Remove the freezer door downwards.

3. Transfer pin on hinge bracket to the opposite side.

Sensor cable opening for freezer compartment Remove sealant.

4. Unscrew the pin on the middle hinge bracket.

5. Pull the refrigerator door to the front and remove it downwards.

Pull out strain relief device. The strain relief device can be found on the inside of the appliance. Refrigerator compartment - top left Freezer compartment - bottom right

Feed sensor through opening and secure sensor cable with strain relief device.

Important! Close the sensor cable openings at the back of the appliance with the sealant provided.

24

6. Unscrew the middle hinge bracket.

5.

4.

EN

7. Transfer upper hinge components to the opposite side.

14. Screw the hinge pin into the middle hinge bracket.

8. Transfer the middle cover plate to the opposite side.

9. Transfer the lower cover plate to the opposite side.

15. Suspend the freezer door on the hinge pin and close.

16. Install the lower hinge bracket. 17. Turn hinge bracket by 90° -

spring is compressed. Screw on hinge bracket.

10. Reinstall the middle hinge bracket on the left-hand side.

11. Pull out the spring mecha-

nism from the refrigerator door and transfer to the opposite side.

18. Transfer the plugs of both doors to the opposite side.

12. Suspend the refrigerator door on the hinge pin and close.

13. Turn the refrigerator door spring

mechanism anticlockwise using the open-ended spanner provided, until the hexagon engages in the recess of the middle hinge bracket. 19. Screw on the handles.

20. Push on pressure plates until they engage.

25