Liftup AS

RAIZER Ver1.9 User Manual

User Manual

44 Pages

File Type: PDF

File Size: 3.07 MB

File Name: Liftup AS - RAIZER Ver1.9 User Manual.pdf

Preview

Page 1

USER MANUAL – RAIZER – AUS VERSION 1.9

Content Content ... 2 1.

Foreword... 4 1.1 Quick Guide ... 4

Declaration ... 5 2.1 Regulatory Approvals ... 7 2.2 EU Declaration of conformity... 9

Type certificate ...10

Intended use ...11

Technical specifications ...12 5.1 Raizer Lifting chair ...12 5.2 Remote control ...13 5.3 Charger ...13

Safety instructions ...14 6.1 Assembly ...14 6.2 Avoiding personal injury ...14 6.3 Overload ...14

Personal safety ...15 7.1 Avoiding personal injury ...15 7.2 Seatbelt ...15 7.3 Handling ...15

Functionality ...16

Prior to use ...17

10. Operation...18 10.1 Assembly and use of the Raizer®...18 10.2 Assembly of left-hand side ...19 10.3 Assembly of right-hand side ...20 10.4 Lifting of person ...22 10.5 Operation of the Raizer® by means of seat buttons ...24 10.6 Operation of the Raizer® by means of remote control* ...26 10.7 How to pair the remote control transmitter and receiver ...27 11. Disassembly ...28 12. Charging of the Raizer® ...29 13. Maintenance ...30 13.1 Cleaning: ...30 13.2 Mechanical maintenance ...30

USER MANUAL – RAIZER – AUS VERSION 1.9

13.3 Remote control* ...30 14. Maintenance checklist ...31 15. Service log book ...33 16. Spare parts ...34 17. Troubleshooting ...40 18. Electrical diagram...41 19. Disposal ...42 20. Right of warranty...42 21. Approvals and certificates ...43

USER MANUAL – RAIZER – AUS VERSION 1.9

1. Foreword Congratulations on purchasing your new Raizer. This is an original user manual for your new Raizer. It is important to read this manual before using the Raizer. The Raizer is a battery-powered mobile lifting chair which can be assembled around a fallen person and raises a fallen person up to an almost standing position in a few minutes. It can be operated by only a single assistant and requires no physical input from the assistant aside from a helping hand. The Raizer is simple to operate by means of the control panel mounted on the side of the seat, or via a remote control*.

*Supplementary equipment

1.1

Quick Guide There is a supplementary Quick Guide in the pocket of the carrying bag. You can store this user manual in the same place.

Scan to retrieve an extra Quick Guide

USER MANUAL – RAIZER – AUS VERSION 1.9

2. Declaration Copyright and Trademarks © Liftup A/S. All rights reserved. Liftup, the Liftup logo and Liftup are trademarks of Liftup A/S, registered in the United States and in other countries. All other trademarks are the property of their respective owners. The following Product Limited Warranty gives Resellers specific legal rights. You may have others, which vary from state/jurisdiction to state/jurisdiction. Product Limited Warranty Subject to the terms and conditions set forth herein, Liftup A/S (“Liftup”) makes the following warranty only to its Resellers who purchase the RAIZER hardware product (“Product”) directly from Liftup: for a period of one (1) year from the date of shipment from Liftup, the Product will substantially conform to Liftup’s standard published specifications for the Product and the Product hardware will be substantially free from defects in materials and workmanship. The foregoing warranty shall not apply to embedded software/firmware components. THIS PRODUCT LIMITED WARRANTY IS PROVIDED TO RESELLERS AND TO RESELLERS ONLY. RESELLER IS SOLELY RESPONSIBLE FOR ANY AND ALL WARRANTIES MADE TO ITS CUSTOMERS, AND LIFTUP MAKES NO WARRANTIES, EXPRESS OR IMPLIED, AND SHALL HAVE NO OBLIGATIONS OR LIABILITY TO RESELLER’S CUSTOMERS OR END-USERS OF THE PRODUCT. RESELLER SHALL NOT MAKE ANY REPRESENTATIONS OR WARRANTIES ON LIFTUP’S BEHALF, AND SHALL FULLY INDEMNIFY, DEFEND AND HOLD LIFTUP HARMLESS FROM ANY BREACH OF THE FOREGOING. IF RESELLER DISTRIBUTES PRODUCT TO END-USER CUSTOMERS, RESELLER SHALL BE SOLELY RESPONSIBLE FOR PREPARING AND PROVIDING PRODUCT WARRANTIES AND PRODUCT LITERATURE TO END-USERS. Warranty Remedies If the Product fails during the warranty period for reasons covered by this Product Limited Warranty and Reseller notifies Liftup of such failure during the warranty period, Liftup at is option will repair OR replace the nonconforming Product, OR refund the purchase price paid by Reseller for the Product, provided that Reseller returns the Product to Liftup in accordance with Liftup’s standard return material authorization procedures or as otherwise instructed by Liftup. Warranty Exclusions and Disclaimers The foregoing Product Limited Warranty shall only apply in the event and to the extent that (i) the Product is properly and correctly installed, configured, interfaced, maintained, stored and operated in accordance with Liftup’s specifications, and (ii) the Product is not modified or misused. This Product Limited Warranty shall not apply to, and Liftup shall not be responsible for, defects or performance problems resulting from: (a) the combination or utilization of the Product with hardware or software products, information, data, systems, interfaces, services or devices not made, supplied or specified by Liftup; (b) the operation of the Product under any specifications other than, or in addition to, Liftup’s standard published specifications for the Product; (c) the unauthorized installation, modification or use of the Product; (d) damage

USER MANUAL – RAIZER – AUS VERSION 1.9

caused by: accident, lightning or other electrical discharge, water immersion or spray, or exposure to environmental conditions for which the Product is not intended; or (e) normal wear and tear on consumable parts, including by way of example and without limitation, batteries. LIFTUP DOES NOT WARRANT OR GUARANTEE THE RESULTS OBTAINED THROUGH THE USE OF THE PRODUCT. THE FOREGOING TERMS OF THE PRODUCT LIMITED WARRANTY STATE LIFTUP’S ENTIRE LIABILITY, AND RESELLER’S EXCLUSIVE REMEDIES, RELATING TO THE USE AND PERFORMANCE OF THE PRODUCT EXCEPT AS OTHERWISE EXPRESSLY PROVIDED FOR IN THIS PRODUCT LIMITED WARRANTY, THE PRODUCT, ACCOMPANYING DOCUMENTATION AND MATERIALS, AND/OR ANY EMBEDDED SOFTWARE/FIRMWARE AND UPDATES THERETO ARE PROVIDED “AS-IS” AND WITHOUT EXPRESS OR IMPLIED WARRANTIES OF ANY KIND, BY EITHER LIFTUP OR ANYONE WHO HAS BEEN INVOLVED IN ITS CREATION, PRODUCTION, INSTALLATION OR DISTRIBUTION, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, TITLE AND NONINFRINGEMENT. THE STATED EXPRESS WARRANTIES ARE IN LIEU OF ALL OBLIGATIONS OR LIABILITIES ON THE PART OF LIFTUP ARISING OUT OF, OR IN CONNECTION WITH, THE PRODUCT. WITHOUT LIMITING THE GENERALITY OF THE FOREGOING: THE PRODUCT MAY CONTAIN TECHNOLOGY THAT IS NOT FAULT TOLERANT AND IS NOT DESIGNED, MANUFACTURED OR INTENDED FOR USE IN ENVIRONMENTS OR APPLICATIONS IN WHICH THE FAILURE OF THE PRODUCT WOULD LEAD TO DEATH, PERSONAL INJURY OR SEVERE PHYSICAL OR ENVIRONMENTAL DAMAGE OR SEVERE FINANCIAL LOSS. ANY USE OR DISTRIBUTION BY RESELLER OR ITS CUSTOMERS IN CONNECTION WITH ANY SUCH ENVIRONMENT OR APPLICATION SHALL BE AT RESELLER’S AND ITS CUSTOMERS’ SOLE RISK, AND LIFTUP SHALL HAVE NO LIABILITY WHATSOEVER IN CONNECTION THEREWITH. RESELLER SHALL INDEMNIFY AND HOLD LIFTUP AND ITS SUPPLIERS HARMLESS FROM ANY CLAIM BROUGHT AGAINST LIFTUP WHICH ARISES FROM RESELLER’S USE OR DISTRIBUTION OF THE PRODUCT IN CONNECTION WITH SUCH ENVIVRONMENTS OR APPLICATIONS. SOME STATES AND JURISDICTIONS DO NOT ALLOW LIMITATIONS ON DURATION OR THE EXCLUSION OF AN IMPLIED WARRANTY, SO CERTAIN OF THE ABOVE LIMITATIONS MAY NOT APPLY TO EVERY RESELLER. Embedded Software/Firmware The Product and associated tools, if any, may contain embedded software/firmware, which is licensed, not sold, and is only for use within the Product as an integral part thereof. Such embedded software/firmware (which includes all updates thereto) contains valuable trade secrets and is proprietary to Liftup A/S and its suppliers. To the greatest extent permitted by law, such embedded software/firmware may not be modified, copied, disassembled, decompiled or reverse engineered. Liftup reserves all other rights. Limitation of Liability LIFTUP’S ENTIRE LIABILITY REGARDING THE PRODUCT SHALL BE LIMITED TO THE AMOUNT ACTUALLY PAID BY RESELLER FOR THE PRODUCT. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL LIFTUP OR ITS

USER MANUAL – RAIZER – AUS VERSION 1.9

SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES WHATSOEVER UNDER ANY CIRCUMSTANCE OR LEGAL THEORY RELATING IN ANY WAY TO THE PRODUCTS, ACCOMPANYING DOCUMENTATION AND MATERIALS, AND ANY EMBEDDED SOFTWARE/FIRMWARE AND UPDATES THERETO (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, LOSS OF DATA OR ANY OTHER PECUNIARY LOSS), REGARDLESS OF WHETHER LIFTUP HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH LOSS AND REGARDLESS OF THE COURSE OF DEALING BETWEEN LIFTUP AND RESELLER. BECAUSE SOME STATES AND JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATION MAY NOT APPLY TO EVERY RESELLER. Notices Class B Statement – Notice to Users. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and the receiver. • Consult the dealer or an experienced radio/TV technician for help. Changes and modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this equipment under Federal Communications Commission rules.

2.1

Regulatory Approvals

CE The RAIZER product comply with the essential requirements of the RED Directive 2014/53/EU as stated by the EU Declaration of Conformity (CE). The RAIZER product comply with the European Telecommunications Standards Institute Specifications EN 300 440 operating in 2.400 GHz to 2.483 GHz band for Radio Equipment and Systems). EU/ International The RAIZER complies with the essential requirements of the 2011/65/EU directive on the restriction of the use of certain hazardous substances in electrical and electronic equipment (ROHS 2). Complies with the essential requirements of the EU 1907/2006 regulation concerning the Registration, Evaluation, Authorisation and Restriction of Chemicals (REACH). Complies with the requirements of the 2002/96/EU directive on waste electrical and electronic equipment and directive 2006/66/EU on batteries and accumulators and waste batteries and accumulators (WEEE).

USER MANUAL – RAIZER – AUS VERSION 1.9

FCC/IC The RAIZER and REMOTE products comply with the FCC Part 15.249 and the Industry Canada requirements RSS-GEN, RSS-210 The RAIZER and REMOTE products complies with Part 15 of the FCC rules and with Industry Canada license exempt standard(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. The RAIZER and REMOTE products are SAR test excluded according to FCC KDB 447498, RSS102 and EN 62479 at separation distances larger than 5 mm and less than 50 mm. With respect to radiofrequency radiation exposure Information, it is declared; that this equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This gives an extra margin, since the remote control normally, only is used in “controlled environment” for approx. 30 seconds when lifting, and typically only a few times a day. MIC (Japan) The RAIZER product complies with the Japanese Ordinance concerning Technical Regulations Conformity Certification etc. of Specified Radio Equipment Article 2 clause (1) Item (19) Low Energy 2400-2483.5 MHz. ACMA (AUS/NZ) The RAIZER product complies with the Australian/New Zealand Radio communication Act 2400-2483 MHz.

RAIZER:

Remote:

FCC ID:

2AK8H-RAIZER1

FCC ID:

2AK8H-REMOTE1

IC-ID:

22516-RAIZER1

IC-ID:

22516- REMOTE1

MIC Certification no.: [R] 202-LSF033

[R] 202-LSF034

EU Declaration of Conformity: CE (RED and Medical Device Directive)

USER MANUAL – RAIZER – AUS VERSION 1.9

2.2

EU Declaration of conformity

Manufacturer:

Liftup A/S

Address:

Hagensvej 21, DK-9530 Støvring tel. +45 9686 3020

Reg. no.

523867 - Danish Medicines Agency

Hereby declares that:

RAIZER®

Medical Device Directive

MDD 93/42/EEC. Medical devices under class 1 (according to rule 1of annex IX of the Council Directive MDD 93/42/EEC). Conformity assessment was performed according to Annex VII. 2014/30/EU. 2011/65/EU. substances in electronic equipment 2014/53/EU, Radio Equipment Directive. CFR 47 Part 15 FCC ID: 2AK8H-RAIZER1 RSS-210 IC-ID: 22516-RAIZER1 ARIB STD-T66 Low power systems. MIC no. [R] 202-LSF033

EMC Directive ROHS-Directive: RED FCC (USA) ISED (Industry Canada) MIC (Japan)

Battery operated mobile lifting chair is in compliance with

Raizer meets the relevant requirements notably in following standards: EN/ISO 10535:2006

Hoist for the transfer of disabled persons Confirmed by Danish Technological Institute, certificate no. 222 EN 12182:2012 Technical aids for disabled general requirements and test methods EN 60601-1:2006+Corr-1,-2:2008 +AC, A1:2013 Safety of Medical Electrical Equipment EN 60601-1-2: 2015 EMC of Medical Electrical Equipment EN 60601-1-11:2015 Home Care CISPR 11, Class B Emission EN 61000-4-2:2009 ESD Electrostatic Discharges EN 61000-4-3:2006+A1:2008+ IS1:2009+A2:2010 Radiated RF Immunity EN 61000-4-8:2010 Magnetic Field EN 62479:2010 Human exposure EN 300 440, v2.1.1 Electromagnetic compatibility + Radio spectrum Matters Draft EN 301489-1, v2.2.0 Electromagnetic compatibility + Radio spectrum Matters Draft EN301489-17, v3.2.0 Electromagnetic compatibility + Radio spectrum Matters AS/NZS 4268 Radio Equipment and Systems – Short Range devices AS/NZS 2772.2 Radio Frequency Fields (mean power < 1 mW)

Testing and conformity assessment performed by Danish Technological Institute, Jens-EMC and Liftup A/S The above products are manufactured under the following management system: EN ISO 9001: 2008 EN 14971: 2012

Director Title

Quality management, Certificate No. 44 100 117583 Application of risk management to medical devices

Flemming Eriksen Name Liftup A/S, Hagensvej 21, DK-9530 Støvring Company

2016-09-15 Date

_____________________________ Signature

USER MANUAL – RAIZER – AUS VERSION 1.9

4. Intended use The Raizer should only be used to bring a person lying on the floor to a seated or almost standing position, who cannot do so by themselves. The person may then require relocation from this position. The max. load of the Raizer is 150kg (330.7 lbs) with max. 1 person at a time on the chair. The max. load is also stated on the CE-mark on the rear of the seat. The Raizer can be used approx. 40 times at full load on a full charge. A charger is included with your Raizer.

Read this user manual thoroughly before using the device. The owner of the device is obliged to maintain it according to the maintenance guide in section 13.

Lifting capacity: Max. 150 kg (330.7 lbs)

Do not push or transport the lifting chair while the person is sitting in it

Do not stand on the lifting chair

Do not use this device in or around water – see 13.1.

Read the user manual thoroughly before using this device.

Fasten the seatbelt before performing a lift

Disconnect and remove the charger before use

Do not dispose of batteries or electrical or electronic equipment with unsorted household rubbish. When disposing of this device, ensure compliance with local ordinances and regulations.

USER MANUAL – RAIZER – AUS VERSION 1.9

5. Technical specifications

Example:

5.1

Raizer Lifting chair

Battery: Number of lifts on a full charge: Duty Cycle: Charging time: Charging of depleted battery: Dimensions (L x W x H): Weight: Lifting capacity: Lifting time: Noise level: Working temperature: Storage temperature: Water and dust: Expected service life:

LiFePo4, 12V, 5AH 40 with a max. load. Approx. 100 with an average load. 1 min. / 5 min. Max. 6 hours (230V charger) 10–15 min = 1 lift Standing 766 x 616 x 1150 mm / 30 x 24 x 45 in. Lying 1291 x 616 x 262 mm / 51 x 24 x 10 in. Seat 9kg. (19,8 lbs.) + legs and back rest 4kg. (8,8 lbs.) – total 13kg. (28,6 lbs.) Max. 150kg. (330.7 lbs) 20-30 secs. < 70 dB A +5ºC to +40ºC/ 41ºF to 104ºF -25ºC to +70ºC / 13ºF to 158ºF IP 42 > 5 years Patented technology Registered design

Right reserved to make technical modifications

USER MANUAL – RAIZER – AUS VERSION 1.9

5.2 Remote control 2,4GHZ Dimensions (L x W x H): Weight: Frequency’s: Power: Battery:

Short Range devices. Receiver Class 3 96 x 47 x 24mm / 3,79 x 1,85 x 0,95 in. 48 g (0,11 lbs.) 2,410GHz 2,435GHz and 2,460GHz <0,6mW duty cycle < 1% 3 Volt CR2032

Water and dust: Working temperature: Storage temperature: Expected service life:

IP 42 +5ºC to +40ºC/ 41ºF to 104ºF -25ºC to +70ºC / 13ºF to 158ºF > 5 years

Right reserved to make technical modifications

5.3

Charger

Charger: Power: Volt: Dimensions (L x W x H): Weight: Working temperature: Storage temperature: Water and dust: Expected service life:

12V. 100-240V nom 90-264 VAC max 15W 14,6V 120 x 47 x 70mm / 4,8 x 1,85 x 2,75 in. 170 g (0,38 lbs.) +5ºC to +40ºC/ 41ºF to 104ºF -25ºC to +70ºC / 13ºF to 158ºF IP 4x > 5 years

Car adapter: Volt:

12 V car adapter 13,8V nom. 14,6V max.

Right reserved to make technical modifications

USER MANUAL – RAIZER – AUS VERSION 1.9

6. Safety instructions 6.1

Assembly

Correct assembling of legs and back rest:

Incorrect assembling of legs and back rest:

Green = right-hand side

Red = left-hand side Observe green marks on right-hand side

6.2

Observe red marks on left-hand side

Avoiding personal injury Although the Raizer comes fitted with various safety features never use it if unintended persons or animals are close by, as there may otherwise be a risk of crushing. Never allow children to play with the Raizer.

6.3

Overload

In order to avoid damage to the device in the event of overload (max. 150kg / 330.7 lbs), it is fitted with an overload cut out, which when triggered halts the lifting chair and issues an audible alarm. In the event of overload, run the chair down to the horizontal position/floor level. With heavy loads on the Raizer, the chair may sink slowly if it is not in operation – this is completely normal. For safety reasons the Raizer is designed to sink slowly under heavy loads. This has been introduced in order to avoid mechanical breakage in the event of overload.

USER MANUAL – RAIZER – AUS VERSION 1.9

7. Personal safety 7.1

Avoiding personal injury -

To avoid personal injury, it is NOT permitted to use the lifting chair when someone or something is at risk of being injured by crushing, cutting, falling, slipping, or similar.

It is important that the assistant ensures that the chair can move without putting anyone or anything at risk.

Be extra careful when there are children and physically or mentally challenged people on or near the chair, as these groups cannot always be expected to be able to foresee the possible consequences of its movements.

Never load more on the chair than the 150kg (330.7 lbs) stated on the loading sign as the maximum load.

DO NOT use the lifting chair until the person is secured with the seat-fitted seatbelt.

7.2

Seatbelt -

The seat is fitted with a seatbelt to secure the person using the chair.

DO NOT use the chair until this person is secured with the seatbelt around their hips.

After assembly of the Raizer under the person on the floor, fasten and click the seatbelt around the hips.

7.3

Handling

The Raizer will normally be supplied by your dealer. The chair is ready for use upon delivery. The Raizer can be transported in the 2 supplied bags. One is a case for the seat itself. The seat is carried by the turquoise handgrip. The back rest and legs are carried in the bags using carrying straps for hand or back (long strap for shoulders, or two straps as a backpack).

USER MANUAL – RAIZER – AUS VERSION 1.9

DO NOT subject the Raizer to severe knocks or blows as this can affect product functionality.

Keep the accompanying remote control* dry and do not subject it to severe blows, such as by throwing it or dropping it, etc. Cleaning may only be done using a well-wrung cloth.

NEVER use a high-pressure jet or running water to rinse the chair, as this can damage the product.

*Supplementary equipment

8. Functionality The Raizer is a battery-powered mobile lifting chair which raises a fallen person up to an almost standing position in 20-30 secs. It can be operated by only a single assistant and requires no physical effort from the assistant aside from a helping hand. It works by the assistant assembling the Raizer around the fallen person and is operated by using the button panel on the seat or by means of the remote control*. The assistant can raise the fallen person to a sitting or almost standing position ready for relocation. To use the Raizer, hold down the button for the entire lift. The lifting will stop if the button is released.

USER MANUAL – RAIZER – AUS VERSION 1.9

9. Prior to use ENSURE that the Raizer is always fully charged. 2 chargers are supplied with the device, and we recommend that the Raizer always be charged and ready for use. You should check the Raizer for power at least once every 6 months and recharge if necessary. See also section 12. Charging of depleted battery:

10–15 min = 1 lift

The Raizer can be stored wherever desired. However, lifting speed will be reduced if the battery temperature falls below 0ºC/32ºF. In practice, though, even if stored in a vehicle in a severe frost (-15ºC/5ºF), if charged, the Raizer will always be able to perform its task.

*Supplementary equipment

USER MANUAL – RAIZER – AUS VERSION 1.9

10. Operation 10.1 Assembly and use of the Raizer®

•

Ensure that the Raizer is fully charged before use. To turn it on, press the up or down buttons on the side of the Raizer.

•

A steady green LED indicates a fully-charged battery.

•

Approach the fallen person

•

Place the seat on the floor by the person's side.

•

Lift the person’s thighs to an angled position.

•

Carefully push the seat in under the person’s thighs.

USER MANUAL – RAIZER – AUS VERSION 1.9

10.2 Assembly of left-hand side Items for assembly on the left-hand side are marked with a red circle.

•

Turn the person’s shoulder by a careful push of the elbow.

•

Carefully push the back rest (marked red for left-hand side) in under the person’s shoulder.

•

Slide the back rest in and click into place in the seat.

•

If necessary, place a foot in front of the seat to prevent it from moving forward.

•

Push the rear leg (marked red for left-hand side) onto the shaft and click into place.

•

Slide the front leg (marked red for left-hand side) into the seat and click it into in place.

•

Note that the snap-lock is to face outwards.

USER MANUAL – RAIZER – AUS VERSION 1.9

10.3 Assembly of right-hand side Items for assembly on the right-hand side are marked with a green circle.

•

Carefully turn the person’s shoulder by a push of the elbow.

•

Carefully push the back rest (marked green for right-hand side) in under the person’s shoulder.

•

Slide the back rest in and click into place in the seat.

•

If necessary, place a foot in front of the seat to prevent it from moving forward.

•

Push the rear leg (marked green for right-hand side) onto the shaft and click into place.

•

Note: right-hand and left-hand rear legs are mounted on the drive shaft so they are parallel, i.e. in the same position as the opposite side

•

Slide the front leg (marked green for right-hand side) into the seat and click it in place.

•

Note that the snaplock is to face outwards.

USER MANUAL – RAIZER – AUS VERSION 1.9

Only raise the chair when you are sure that the person’s feet, arms, hands or other body parts are not at risk of being struck or run over by the action of the chair!

THE REAR LEGS The rear legs are fitted horizontally and lie just above the floor along the shoulder (as in the illustration). Should this not be the case, be careful to fit both rear legs in parallel.

Be aware of the positioning of the shoulders and make sure that the arms are crossed upon the chest, due to the fact that the rear legs move down towards the floor as soon as the up button is pressed. This may put the person’s shoulders and arms at risk of injury if not positioned correctly.

If the legs are mounted in a higher position, pay attention to the rotating legs moving towards the floor. Make sure no body parts or clothes are at risk of being struck of the rotating legs.

THE FRONT LEGS Ensure that the person’s legs are together and their feet/legs are not at risk of getting in under a front leg when the chair is raised, as the front legs move toward the floor before the chair begins to lift its user.

USER MANUAL – RAIZER – AUS VERSION 1.9

10.4 Lifting of person

•

After assembly of the Raizer under the fallen person, wrap and click the seatbelt around their hips.

•

The Raizer is now ready to lift the user.

•

Support the person’s neck with one hand.

•

Press the “up arrow” on the side panel or remote control*

•

The Raizer can be operated from either side.

Previous Page Next Page