EndoVue 19, 21, 24 and 32 inch Display User Manual Rev E March 2021

© 2021 NDS Surgical Imaging, LLC. All rights reserved. Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the contents. This document is subject to change without notice. NDS provides this information as reference only. Reference to products from other vendors does not imply any recommendation or endorsement. This document contains proprietary information protected by copyright. No part of this manual may be reproduced by any mechanical, electronic, or other means, in any form, without prior written permission of NDS. All trademarks are the property of their respective owners.

Table of Contents Safety Information... iii Warnings and Cautions... iii Power Supply... iv Power Cord... iv Grounding... iv Intended Use and Contraindications... iv Safety Precautions... v Image Retention Notice... v Recycling... v Terms and Conditions... vi Declarations of Conformity... vi Legal Statement... vi Standard Warranty and Service... vii VESA Compliant Display Mounting... 1 Monitor Stand Installation... 1 Enclosure Assembly and Cleaning... 2 Cable Cover Installation... 2 Cleaning Instructions... 2 General maintenance information... 2 Display User Interface... 3 Display Keypad... 3 Menu Navigation... 3 INPUT and MENU Buttons: Open OSD Menus... 3 SCROLL Button: Vertical Selection Control... 3 Left/Right Buttons: Horizontal Selection Controls... 3 Input Menu... 3 Display Menu... 4 Picture Menu... 4 Color Menu... 5 Setup Menu... 5 Defaults Menu... 6 Image Adjustment... 6 Connector Panel Overview... 7 EndoVue Connector Panel... 7 Connector Types... 7 Data Connectors and Pinouts... 7 DVI-I Digital and Analog... 7 VGA... 8 S-Video... 8 Composite... 8 Firmware Connector and Pinout... 8 Mini USB... 8 Power Connector and Pinout... 9 24 VDC Connector... 9 Electrical Symbols... 9 Optional 5 VDC Fiber Power Cable... 9 Cable Bend Radius... 9 Specifications...11 Specifications...11 Supported Resolutions...11 DVI Supported Resolutions...11 VGA, RGBS, and YPbPr Supported Resolutions...12 EndoVue Parts List by Region...12 Troubleshooting...13 Table of Contents | i

Electromagnetic Compatibility Tables...15 Electromagnetic Emissions...16 Electromagnetic Immunity...17 Recommended Separation Distances...18

ii | Table of Contents

Safety Information Warnings and Cautions This symbol alerts the user that important information regarding the installation and/or operation of this equipment follows. Information preceded by this symbol should be read carefully in order to avoid damaging the equipment. This symbol warns the user that un-insulated voltage within the unit may have sufficient magnitude to cause electrical shock. It is dangerous to make contact with any part inside the unit. To reduce the risk of electric shock, DO NOT remove cover (or back). NOTE: There are no user serviceable parts inside. Refer servicing to qualified service personnel. This symbol cautions the user that important information regarding the operation and / or maintenance of this equipment has been included. Information preceded by this symbol should be read carefully to avoid damage to the equipment. This symbol denotes the manufacturer.

This symbol denotes the manufacturer’s European Community representative. This symbol indicates the device is a Medical Device. This product is intended only for use by healthcare professionals in professional healthcare environments. EndoVue series monitors are designed to display high quality video and graphic images for use in a medical environment. They are designed to accept all standard video and graphic signals, and most special timings from medical equipment. Built-in video controllers convert and format incoming signals of various signal types to match the resolution of the LCD panel. The user can make adjustments to video parameters using the front keypad of the monitor with the On Screen Display (OSD) interface to optimize the viewing experience for different applications. To prevent fire or shock hazards, do not expose this unit to rain or moisture. Also, do not use this unit's polarized plug with an extension cord receptacle or other outlets unless the prongs can be fully inserted. The product is designed to meet the medical safety requirements for a patient vicinity device. Warning: To avoid risk of electric shock, this equipment must be only connected to a supply mains with protective earth. Note: Any serious incident or adverse event that has occurred in relation to the device should be reported to the manufacturer and the competent authority of the Member State in which the user and/or patient is established. The installation shall only be carried out by NDS authorized and trained personnel. This device is only intended to be used in professional healthcare environment. This equipment/system is intended for use by healthcare professionals only. This product is a Class I medical device. No modifications are allowed. Monitors are intended for continuous operation.

S&E

Safety Compliance This product is T.U.V. approved with respect to electric shock, fire and mechanical hazards only in accordance with CAN/CSA C22.2 No. 60601-1 and ANSI/AAMI ES60601-1. Safety Compliance This device meets the requirements of EN60601-1 so as to conform to the Medical Device regulation 2017/745. Safety and EMI Compliance GB9254, GB4943.1 and GB17625.1

Safety Information | iii

Power Supply For Customers in North America EndoVue series monitors comply to the above standards only when used with the supplied hospital grade power supply. Note: This power supply is a part of the medical device. Model BridgePower BM060S24F AC Input 100 - 240 Volts, 50 to 60 Hz DC Output 24 Volts, 2.7 Amps

For Customers in China This power supply is to be used with this monitor. Model BridgePower BM060S24F AC Input 100 - 240 Volts, 50 to 60 Hz DC Output 24 Volts, 2.7 Amps

Power Cord For Customers in North America Use a hospital grade power cord with the correct plug for your power source. The power cord is the only recognized disconnect device. Disconnect the power cord from the AC mains. MEDICAL EQUIPMENT should be positioned so that the disconnect device is readily accessible. Monitors should be powered from a center tapped circuit when used in the US at voltages over 120 volts. For Customers in China Use China Compulsory Certificate (CCC)-approved power cord. For Customers in Japan The supplied power cord is for use only with this monitor.

Grounding This product is energized from an external electrical power source for Class 1 equipment. It is the responsibility of the installer to test the product’s earth ground to verify that it complies with the hospital, local and national impedance requirements. A ground post is located on the back of the product to use for grounding the chassis of the unit. Any such ground must be installed in accordance with applicable electrical codes. The ground post location is shown in the EndoVue Connector Panel diagram on page 7. Grounding reliability can only be achieved when the equipment is connected to an equivalent receptacle marked “Hospital Only” or “Hospital Grade.”

Intended Use and Contraindications Intended Use EndoVue series monitors are intended for use in a medical environment to display high quality video and graphic images. Contraindications 1. Do not use this product in the presence of flammable anesthetics mixture with air, oxygen or nitrous oxide. 2. No part of this product may come in contact with a patient. Never touch the product and a patient at the same time. 3. This product is capable of displaying Radiology (PACS) images for reference, not diagnostic, purposes only. 4. For mission critical applications, we strongly recommend that a replacement unit be immediately available.

iv | Safety Information

Safety Precautions External equipment intended for connection to signal input/output or other connectors shall meet the level of safety equivalent to ME equipment complying with the relevant standard. In addition, all such combinationssystems shall comply with the standard. Equipment not complying with UL/EN/IEC 60601-1 shall be kept outside the patient environment, as defined in the standard. Any person who connects external equipment to the signal input, signal output, or other connectors has formed a system and is therefore responsible for the system to comply with the requirements of IEC or ISO safety standards. If in doubt, speak with a qualified technician. If such equipment and other medical devices are connected to form a medical electrical system(s), a green light indicator shall be provided on the final ME system(s) to indicate that this equipment is ready for normal use.

Image Retention Notice Warning: Leaving a fixed (constant) image on the monitor for a long period of time can result in image retention. Avoid leaving a fixed image on the monitor, or turn the monitor off when it is not in use.

Recycling Follow local governing ordinances and recycling plans regarding the recycling or disposal of this equipment.

Safety Information | v

Terms and Conditions Declarations of Conformity FCC and Council Directives of European Standards This device complies with Part 15 of FCC rules and conform to the 2017/745 Medical Device Regulation. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesirable results. 1. Use the attached specified cables with the color monitor so as not to interfere with radio and television reception. Use of other cable and adapters may cause interference with other electronic equipment. 2. This equipment has been tested and found to comply with the limits pursuant to FCC part 15 and CISPR 11. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. IEC This equipment has been tested and found to comply with the limits for medical devices to the IEC 60601-1-2. These limits are designed to provide reasonable protection against harmful interference in a typical medical installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to other devices in the vicinity. FCC, Council Directives of European Standards, and IEC: There is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult your dealer or an experienced radio/TV technician for help. Accessory equipment connected to this product must be certified according to the respective IEC Standards (i.e., IEC 60950-1) for data processing equipment and IEC 60601-1 for medical equipment. Furthermore, all configurations shall comply with the system standard, IEC 60601-1-1. Anyone who connects additional equipment to the signal input part or signal output part configures a medical system, and is therefore responsible that the system complies with the requirements of system standard IEC 60601-1-1. Whoever is responsible for securing the unit to a system needs to insure that the mounting equipment used with this product complies to IEC standard 60601-1. If in doubt, consult the technical services department or your local representative.

Legal Statement NDS may sell its products through other medical device manufacturers, distributors and resellers and therefore, purchasers of this NDS product should consult with the entity through which this product was originally purchased regarding the terms of any applicable product warranties provided by such entity, if any. NDS neither assumes nor authorizes any person to assume for it any other liabilities in conjunction with and/or related to the sale and/or use of its products. To ensure proper use, handling and care of NDS products, customers should consult the product specific literature, instruction manual, and/or labeling included with the product or otherwise available. Customers are cautioned that system configuration, software, the application, customer data and operator control of the system, among other factors, affect the product’s performance. While NDS products are considered to be compatible with many systems, specific functional implementation by customers may vary. Therefore, suitability of a product for a specific purpose or application must be determined by the customer and is not warranted by NDS. NDS SPECIFICALLY DISCLAIMS ALL WARRANTIES OF ANY KIND, WHETHER EXPRESS, IMPLIED AND/OR STATUTORY, INCLUDING, BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, FITNESS AND/OR OF SUITABILITY FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT WITH RESPECT TO ALL NDS PRODUCTS OR SERVICES. ANY AND ALL OTHER WARRANTIES, REPRESENTATIONS AND/OR GUARANTEES, OF ANY TYPE, NATURE OR EXTENT, BE IT IMPLIED, EXPRESS AND/OR WHETHER ARISING UNDER OR AS A RESULT OF ANY STATUTE, LAW, COMMERCIAL USAGE, CUSTOM, TRADE OR OTHERWISE, ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED. vi | Terms and Conditions

NDS, its suppliers and/or distributors are not liable, directly or by way of indemnity for any special, incidental, consequential, punitive, exemplary or indirect damages, including but not limited to alleged damages for delayed shipment, non-delivery, product failure, product design or production, inability to use such products or services, loss of future business (lost profits), or from any other cause, whatsoever, in connection with or arising from the purchase, sale, lease, rental, installation or use of such NDS products, these terms and conditions, or with respect to any the terms of any agreement which incorporates these terms and conditions. SOME JURISDICTIONS DO NOT ALLOW EXCLUSIONS AND DISCLAIMERS OF CERTAIN WARRANTIES OR LIMITATIONS OF LIABILITY, SO THE LIMITATIONS AND/OR EXCLUSIONS, SET FORTH HEREIN, MAY NOT APPLY. IN THAT EVENT LIABILITY WILL BE LIMITED TO THE GREATEST EXTENT PERMITTED BY LAW IN THE SUBJECT JURISDICTION. The information provided in this document, including all designs and related materials, is the valuable property of NDS and/or its licensors and, as appropriate, they reserve all patent, copyright, and other proprietary rights to this document, including all design, manufacturing reproduction, use, and sales rights thereto, except to the extent said rights are expressly granted to others.

Standard Warranty and Service COVERAGE: NDS warrants this product to be in compliance with the specifications provided by NDS and to be free from defects in material and workmanship as defined in such specifications. Subject to the conditions set forth below, NDS agrees to repair or replace any part of the enclosed unit for the length of period indicated on the chart below: NDS Product

Standard Warranty Coverage

EndoVue Series 19", 21", 24" and 32"

1 Year from date of shipment by NDS

WARRANTY SERVICE - REPAIR & RETURN 1. Our standard warranty service is “Repair and Return.” Repair and Return requires the defective unit to be returned to our service location for repair. 2. Cost of shipment of the defective unit to NDS is the responsibility of the customer. Cost of shipment of the repaired unit to Customer is the responsibility of NDS. 3. NDS reserves the right in its sole discretion to provide Customer with a comparable refurbished replacement unit in lieu of repair of customer's defective unit. 4. If NDS is unable within a reasonable time to repair or replace the defective unit, it shall refund the purchase price for the product paid by the customer (exclusive of taxes, installation and shipping related fees). EXCLUSIONS - WHAT IS NOT COVERED 1. Any product with a defaced, modified, or removed serial number. 2. Damage, deterioration or a malfunction resulting from accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or failure to follow instructions supplied with the product. 3. Cosmetic damage including, but not limited to: scratches, cracks, dents, markings, glue and adhesive residue. 4. Any damage of the product due to shipment. 5. Any damage caused by factors external to the product, such as electric power fluctuation or failure. 6. Normal wear and tear. 7. Removal, installation, and set-up service charges. 8. Failures not reported within the warranty term. 9. Any NDS products purchased through a distributor, reseller, or medical device manufacturer other than NDS (each, an “Intermediary”), where such Intermediary provides direct warranty service to its end-user customers in connection with such product. a. An Intermediary may provide their end-user customers direct warranty support. Please contact NDS Customer Service to determine if the product that you purchased is covered by this Standard Limited Warranty or whether you need to contact the Intermediary through which you purchased the product for warranty service.

Terms and Conditions | vii

CONTACTING NDS CUSTOMER SERVICE Country United States

Phone + 408-754-4210

Email [email protected]

Time Available 7am to 5pm PST

Europe

+420 530 511 900

[email protected]

7am to 5pm CET

China

+86 10 8559 7856

[email protected]

9am to 5pm

Japan

+ 81-3-5753-2466

[email protected]

9am to 5:30pm

1. Contact NDS Customer Service during the hours listed above. Have your NDS model number and serial number available. You may be required to provide proof of purchase as a condition for receiving warranty service. 2. Our representative may perform troubleshooting and diagnosis of the problem over the telephone/email. If our representative is unable to fix the problem over the phone/email, we will issue a Return Material Authorization (RMA) for the non-functioning unit and provide return instructions. 3. Upon receipt of the returned product, a service technician will evaluate the unit and confirm the failure description provided by the customer. a. If the found failure type is covered under warranty, the repair, parts, labor and shipment back to the customer will be at no charge. b. If the found failure type is not covered under warranty, NDS’s then current evaluation fee will apply in addition to the cost of parts, labor and the return shipment. c. If the unit is within the warranty period but the customer does not provide a problem description and the service technician cannot determine the failure (no problem found - “NPF”) NDS’s then current evaluation fee will apply in addition to return shipment. Payment for Non-Warranty Evaluations and Repairs and other Evaluation Charges: Non-warranty repairs requested by the customer will be performed at NDS's then current rates for any non-warranty repairs and will include applicable evaluation fees and the cost of return shipping (if customer requests that NDS ship the repaired product). NDS further reserves the right, in its sole discretion, to request pre-payment for any nonwarranty repairs, NPF evaluations, and return shipping charges prior to return of the product to customer. Any invoiced amount not paid when due shall be subject to a service charge equal to the lesser of one and one-half percent (1.5%) per month or the maximum rate permitted by law. If NDS undertakes collection or enforcement efforts, customer shall be liable for all costs thereof, including attorney's fees. NDS reserves the right to suspend warranty coverage to any customer who is in default of payment until such payment has been made. DISCLAIMER This limited product warranty sets forth your sole and exclusive remedy and NDS's sole and exclusive liability under the Standard Limited Warranty described herein. There are no warranties, express or implied, which extend beyond the description contained herein including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or non-infringement. NDS's liability is limited to the cost of repair or replacement of the product. NDS shall not be liable for: 1. Damage to other property caused by any defects in the product, damages based upon inconvenience, loss of use of the product, loss of time, loss of profits, loss of business opportunity, loss of goodwill, interference with business relationships, or other commercial loss, even if advised of the possibility of such damages. 2. Any other damages, whether incidental, indirect, consequential or otherwise. 3. Any claim against the customer by a third party. End-users are cautioned that system configuration, software, the application, customer data and operator control of the system, among other factors, affect the product performance. While NDS products are considered to be compatible with many systems, specific functional implementation by the customers of the product may vary. Therefore, suitability of a product for a specific purpose or application must be determined by consumer and is not warranted by NDS. This warranty gives you specific legal rights. You may have other rights, which may vary from locality to locality. Some localities do not allow limitations on implied warranties and/or do not allow the exclusion of incidental or consequential damages, so the above limitations might not apply to you.

viii | Terms and Conditions

VESA Compliant Display Mounting EndoVue series displays are compliant with the VESA Mounting Interface Standard, with MIS hole mount patterns configured to size and weight of the display, suitable for stand, wall, or armature mounting. MIS-D 100 x 100 mm and MIS-E 200 x 100 mm interfaces are shown below.

M4 X 0.7 Thread (4x)

100 mm M4 X 0.7 Thread (4x)

100 mm

200 mm

Monitor Stand Installation To install the EndoVue monitor stand (optional for 19", 21", and 24" monitors), place the monitor screen-down on a clean, flat surface and position the four mounting screw holes of the stand mounting bracket over the fourhole attachment interface on the monitor back. Insert one of the four provided cap screws into a screw hole and lightly tighten. Repeat the process with the remaining screws, and then check to confirm that the mounting bracket is flat against the back surface of the monitor before tightening all screws securely. Note: Mounting bracket of the stand can be tilted up to 30°. Mounting Bracket

M4 Cap Screw (4x)

Warning: The mounting bracket screws must be securely tightened. Failure to properly secure the mounting bracket to the display could be hazardous. Use suitable mounting apparatus to avoid risk of injury. VESA Compliant Display Mounting | 1

Enclosure Assembly and Cleaning Cable Cover Installation 1. 2. 3. 4.

Connect power, control, and video cables before installing the cable cover. Align the cable cover to the cable well recess on the back of the display. Slide the cable cover forward into the recess, with cables positioned under the cut-out. Slide the cable cover forward until tabs on the bottom edge click into place.

Cleaning Instructions General maintenance information EndoVue series monitors do not require any scheduled maintenance or calibration activities. If any abnormal situation found, please return the display to our approved maintenance organization. For any questions, please call Customer Service for assistance at (877) 637-1110. Warning: Prior to cleaning, the display should be turned OFF and disconnected from the power source. • Do not allow liquids to enter the interior of the unit, as severe damage to the unit can result. • Do not use solvents such as benzene or thinner, or any acid, alkaline or abrasive detergents. Front Glass: Thoroughly wipe the front glass surface with a lint-free cloth. For persistent spots or smudges, use a lint-free cloth dampened with distilled water. Do not use any harsh solvents, abrasive detergents or chemical cleaning cloths. Plastic Enclosure: Wipe all exterior surfaces with a lint-free cloth dampened with distilled water or a mild glass cleaner such as 70% isopropyl alcohol, Vinegar (distilled white vinegar, 5% acidity). If a mild glass cleaner is used, remove any residual cleaning material by wiping all exterior surfaces with a lint-free cloth dampened with distilled water afterwards. Note: Do not use the following products: • MEK (Methyl Ethyl Ketone) • Toluene • Acetone • Benzene or thinner • Acid • Alkaline or abrasive detergents • Chemical Cleaning cloths

2 | Enclosure Assembly and Cleaning

Display User Interface Display Keypad The Display Keypad is centered on the lower front surface of the display enclosure, providing controls for adjustment of display parameters using the On Screen Display (OSD) Menu system.

INPUT

MENU

SCROLL

Menu Navigation INPUT and MENU Buttons: Open OSD Menus To open the Input Menu, press the INPUT button. To open the Display Menu, press the MENU button. INPUT

MENU

SCROLL Button: Vertical Selection Control To enter a menu and begin a parameter selection process, press the SCROLL button. The top parameter row is first selected, and the selection moves downward to the next row with each successive press of the button. SCROLL To exit a menu, use the SCROLL button to move the selection to the bottom menu row, and then press the SCROLL button just once to highlight the menu tab, where you can use the or buttons to select another menu tab.

Left/Right Buttons: Horizontal Selection Controls To adjust a parameter, select the parameter row using the SCROLL button, then press the buttons to make the adjustment or to select a setting.

or

Input Menu INPUT

To select or change an input source, press the INPUT button to access the Input Menu. press the SCROLL button to highlight the desired input and press the button to select it. A √ symbol in the left column designates the active input.

The Input Menu automatically closes 30 seconds after the last action. It can also be closed by pressing the INPUT button.

Display User Interface | 3

Display Menu MENU

To open the Display Menu, press the MENU button. The Picture Menu displays by default, with details of the current video input listed across the top of the menu above the menu tabs. To select other menus, press the or buttons to highlight the menu tab, then press the SCROLL button to enter the menu.

or To adjust a parameter, press the SCROLL button to move the row selection down to it, and then press the buttons to adjust the parameter or to select a setting. Parameter adjustments are applied in real time while changing values or settings. The Display Menu automatically closes 30 seconds after the last action. It can also be closed by pressing the MENU button. Note: Grayed out descriptions indicate parameters not available for the current signal or input configuration.

Picture Menu Note: Picture Menu display only those parameters that apply to specific input signals. Horizontal Position (All except DVI-D) To horizontally center the image, press the or buttons. Vertical Position (All except DVI-D) To vertically center the image, press the or buttons. Sharpness To adjust sharpness (edge enhancement) of the displayed image, press the or buttons. Phase (VGA/RGBS, YPbPr only) To adjust phase of the display pixel clock, press the or buttons. Frequency (VGA/RGBS, YPbPr only) To adjust frequency of the display pixel clock until the image fills the screen horizontally, first set Scaling to Fill, and press the or buttons. Overscan (Video) Parameter enabled when the input is 16:9, 480P, 576P, or interlaced. Press the or buttons to select. 0: The image is displayed at a size that fills the screen without losing any video information. Image could be displayed as letterboxed, with black bars top and bottom or left and right. 1, 2, 3, 4, 5 or 6: Incrementally enlarges and crops the centered image. As the image becomes larger, video information is lost on all sides. Scaling (Graphics) Parameter enabled when input signal is not 16:9, 480P, 576P, or interlaced. Press the or buttons to select. Fill: Expands the video image to fill the entire screen. The aspect ratio may not be accurately displayed. Aspect: Expands the video image until its largest dimension fills the screen while retaining the aspect ratio. The image may be displayed as letterboxed, with black bars top and bottom or left and right. 1:1: Displays the video data in its native size and aspect ratio. Image with aspect ratios different from that of the display are letterboxed, with black bars top and bottom or left and right. SmartSync™/Alternative Modes (VGA/RGBS, YPbPr only) NDS proprietary SmartSync technology examines incoming signals to automatically display the video image in its proper format. Alternative Modes are used to manually distinguish between modes whose timing characteristics are very close. SmartSync: To enable SmartSync, press the button. Alternative Modes: To make an Alternative Modes adjustment, press the button. After selecting Alternative Modes. the mode changes incrementally each time the button is pressed until the selected mode equals the maximum available. The next press of the button restores the initial mode.

4 | Display User Interface

Video Format (Composite, SDI, S-Video only) Auto: Examines incoming signals to automatically display the video image in NTSC or PAL format. NTSC/PAL: Press the or buttons to manually select.

Color Menu Gamma To select a gamma setting, press the or buttons.. 1.8, 2.0, 2.2, 2.4 or 2.6: Preset gamma values Video: Linear gamma Look Up Table (LUT) PACS: DICOM gamma LUT This product is capable of displaying Radiology (PACS) images for reference purposes only. Color Temperature To select a preset color temperature, press the or buttons. 5500, 6500, 8000, 9300: Preset color temperatures. User: If a preset color temperature is selected, and any other parameter is subsequently changed, the resulting values are copied to the Color Correction User presets and User is selected Red, Green, Blue To increase or decrease the intensity of the selected color, press the or buttons. Saturation To set the saturation (color intensity) of the image, press the or buttons. Hue To set the hue (color tint) of the image, press the or buttons.

Setup Menu Menu Position: To select from nine preset screen locations for display of the OSD menus, press the or buttons. Language: To select one of 18 languages: Chinese, Danish, Dutch, English, Finnish, French, German, Greek, Italian, Japanese, Korean, Norwegian, Polish, Portuguese, Russian, Spanish, Swedish, and Turkish, press the or buttons. DPMS Enable To enable or disable Display Power Management System (DPMS), press the or buttons. Off: Default setting. On: If there is no input signal, a “D.P.M.S” message displays for 10 - 15 seconds before the display goes into Power Saving mode. The display turns on when the input signal is restored. Auto Source Select To disable or enable Auto Source Select, press the or buttons. Off: Video input is manually selected. On: Searches through all possible input sources until an active video source is found. Menu Lock To enable Menu Lock, press the button. Off: Default setting. On: Disables access to OSD menus to prevent inadvertent changes to display settings. The OSD closes, and a MENU LOCKED message displays briefly. To unlock OSD access, simultaneously press and hold the MENU and SCROLL buttons until a MENU UNLOCKED message displays.

Display User Interface | 5

Operating Hours Displays in hours and minutes the accumulated time the monitor has been in use. FW Version number of the display firmware.

Defaults Menu Factory Defaults To return all changed parameter settings to factory preset values, press the button. The “Restoring Factory Defaults” message displays while processing.

User Defaults To save changes to default parameters in a User Default profile, press the SCROLL button to select a User Defaults profile marked ***EMPTY*** and press the “Saving User Defaults” message displays while processing.

button to save the profile. The

To restore a User Defaults profile after changing other parameters, select the saved User Defaults profile and press the button. The “Restoring User Profile” message displays while processing. To clear a User Defaults profile, select the saved User Defaults profile and press the (Brightness/Contrast) button. The “Clearing User Profile” message displays while processing.

Image Adjustment Brightness/Contrast Button Press the (Brightness/Contrast) button once to access the Brightness control. Press the button twice to access the Contrast control, or press it three times to access the Backlight control. Press the or buttons to adjust the controls. Brightness Control To adjust brightness of the designated input, press the or buttons. NOTE: Setting brightness too high or too low reduces the range of shadow and highlight detail of the displayed image. Contrast Control To adjust contrast of the designated input, press the or buttons. Note: Setting contrast too high or too low reduces the range of shadow and highlight detail of the displayed image, with a negative effect on color saturation. Backlight Control To adjust the backlight level of your monitor, press the Note: Lower backlight levels increase backlight lifetime.

6 | Display User Interface

or

buttons.

Connector Panel Overview EndoVue Connector Panel DVI / RGBS IN

SDI IN

DVI RE-DRIVE

5 VDC OUT

USB IN

VGA / RGBS IN

S-VIDEO COMPOSITE GROUND IN IN POST

24 VDC INPUT

Notes 1. DVI-I/RGBS connector accepts DVI, RGBS or YPbPr signals. 2. DVI RE-DRIVE provides Digital output. 3. SDI connector is a future option. 4. 5VDC / 1A connector provides 5 VDC / 1A output. 5. USB connector is used only for installing firmware upgrades. 6. VGA/RGBS connector accepts RGBS, YPbPr or VGA signals.

Connector Types Inputs

Connector Types

DVI / RGBS / YPbPr VGA / RGBS / YPbPr Composite S-Video

DVI-I, Digital 100 Ohm differential, Analog 75 Ohm terminated HD-15, 75 Ohm terminated BNC, 75 Ohm terminated DIN-4, 75 Ohm terminated

Data Connectors and Pinouts DVI-I Digital and Analog DVI-I IN Supports digital and analog (RGBS / YPbPr) signals. Analog data appears on pin 8, and pins C1 - C5. 1 9 17

8 16 24

C1 C2 C5 C3 C4

Pin Signal

Pin Signal

Pin Signal

1

T.M.D.S. DATA 2-

11

T.M.D.S. DATA 1/3 SHIELD

21

N/C

2

T.M.D.S. DATA 2+

12

N/C

22

T.M.D.S. CLOCK SHIELD

3

T.M.D.S. DATA 2/4 SHIELD

13

N/C

23

T.M.D.S. CLOCK+

4

N/C

14

+5V POWER

24

T.M.D.S. CLOCK-

5

N/C

15

GND

DVI-I IN Only

6

DDC CLOCK

16

HOT PLUG DETECT

C1

ANALOG RED

7

DDC DATA

17

T.M.D.S. DATA 0-

C2

ANALOG GREEN

8

ANALOG VERTICAL SYNC (DVI-I IN Only)

18

T.M.D.S. DATA 0+

C3

ANALOG BLUE

9

T.M.D.S. DATA 1-

19

T.M.D.S. DATA 0/5 SHIELD

C4

ANALOG HORIZONTAL SYNC

10

T.M.D.S. DATA 1+

20

N/C

C5

ANALOG GROUND

Connector Panel Overview | 7

VGA VGA IN supports RGBS 2, YPbPr signals. 1 6 11

5 10 12

Pin Description

Pin Description

Pin Description

1

RED

6

GND RED

11

N. C.

2

GREEN

7

GND GREEN

12

DDC_SDA

3

BLUE

8

GND BLUE

13

HORIZ SYNC

4

N.C.

9

+5VD

14

VERT SYNC.

5

GND

10

SYNC GND

15

DDC_SCL

S-Video 4 3 2 1

Pin Name

Description

1

GND

Ground (Y)

2

GND

Ground (Y)

3

Y

Intensity (Luminance)

4

C

Intensity (Chrominance)

Composite 1

2

Pin Name

Description

1

DATA

Pin

2

GROUND Sleeve

Firmware Connector and Pinout Mini USB Flash Upgrade Cable, part number 35Z0047, is available from NDS. 1

8 | Connector Panel Overview

5

Pin Name

Description

1

Vcc

+5 VDC

2

D Minus Data Return

3

D Plus

4

ID

5

GND

Data Transmit Ground

Power Connector and Pinout 24 VDC Connector 3 1 2

Pin Name

Description

1

+24 VDC

Power Input

2

GND

Ground

3

Shield

Ground

Electrical Symbols

Equipotentiality This symbol appears next to the display Potential Equalization Conductor (ground post). Closed (On) Switch This symbol appears below the closed, or on, side of the display On/Off switch. Open (Off) Switch This symbol appears below the open, or off, side of the display On/Off switch.

Optional 5 VDC Fiber Power Cable J1 Pinout 2 1

J1

J2 Pinout 1 2 5 VDC OUT

NDS 35X0100

Connector Center (1)

5 VDC FIBER

J2

Shield (2)

J1

+5 VDC

Return

J2

+5 VDC

Return

To purchase the optional 5 VDC Fiber Power Cable (P/N 35X0100) contact: North America and Asia Pacific: [email protected] Europe: [email protected]

Cable Bend Radius We recommend that the bend radius of metallic cables be no less than 63 mm (2.5 inches) or 7 times the diameter of the cable whichever is greater. The bend radius of Fiber Optic cables should be no less than 10 times the diameter of the cable. Sharper bends can damage the cable, and/or degrade the video signal.

Connector Panel Overview | 9

10 | Connector Panel Overview