Radiance G2 HB 2 inch Display User Manual Rev M March 2021

© 2021 NDS Surgical Imaging, LLC. All rights reserved. Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the contents. This document is subject to change without notice. NDS provides this information as reference only. Reference to products from other vendors does not imply any recommendation or endorsement. This document contains proprietary information protected by copyright. No part of this manual may be reproduced by any mechanical, electronic, or other means, in any form, without prior written permission of NDS. All trademarks are the property of their respective owners.

Table of Contents Tab 1 Warnings and Cautions ----------------------------------------------------------------------------- ii Recycling ------------------------------------------------------------------------------------------------- iii Declarations of Conformity ------------------------------------------------------------------------ iv Legal Statement -------------------------------------------------------------------------------------- v Tab 2 About This Manual ------------------------------------------------------------------------------------ 1 Intended Use and Contraindications ------------------------------------------------------------ 1 Image Retention Notice----------------------------------------------------------------------------- 1 Quick Startup ------------------------------------------------------------------------------------------- 1 Powering On The Unit----------------------------------------------------------------------------- 1 First Time Users and Initial Test----------------------------------------------------------------- 1 Tab 3 Connector Panels -------------------------------------------------------------------------------------- 2 Electrical Symbols ------------------------------------------------------------------------------------- 3 Tab 4 Control---------------------------------------------------------------------------------------------------- 4 Quick Select --------------------------------------------------------------------------------------------- 4 Image Adjustments ----------------------------------------------------------------------------------- 5 Brightness--------------------------------------------------------------------------------------------- 5 Contrast ----------------------------------------------------------------------------------------------- 5 Backlight ---------------------------------------------------------------------------------------------- 5 Tab 5 Menu Systems Overview ---------------------------------------------------------------------------- 6 Video Source -------------------------------------------------------------------------------------------- 7 PIP and Swap ------------------------------------------------------------------------------------------- 8 GPIO ------------------------------------------------------------------------------------------------------- 9 Priority Input Select ----------------------------------------------------------------------------------- 9 Display Setup ----------------------------------------------------------------------------------------- 10 HD SDI Picture Menu ---------------------------------------------------------------------------- 10 SD SDI, S-Video and Composite Picture Menu ------------------------------------------- 10 VGA, SOG, RGBS and YPbPr Picture Menu ------------------------------------------------- 11 DVI-Digital Picture Menu ----------------------------------------------------------------------- 12 Color Menu ----------------------------------------------------------------------------------------- 13 Setup Menu ---------------------------------------------------------------------------------------- 14 Defaults Menu ------------------------------------------------------------------------------------- 15 Tab 6 Troubleshooting ------------------------------------------------------------------------------------- 16 Tab 7 Drawing and Dimensions ------------------------------------------------------------------------- 17 Tab 8 Data Connectors and Pinouts -------------------------------------------------------------------- 18 Cable Bend Radius ---------------------------------------------------------------------------------- 18 Control Connectors and Pinouts ---------------------------------------------------------------- 19 Power Connector and Pinout -------------------------------------------------------------------- 19 Tab 9 Specifications ----------------------------------------------------------------------------------------- 20 Video Inputs ---------------------------------------------------------------------------------------- 21 Video Formats ------------------------------------------------------------------------------------- 21 Cleaning and Disinfecting Instructions-------------------------------------------------------- 22 Electromagnetic Compatibility (EMC) Tables ------------------------------------------------ 23

i

Safety Information Warnings and Cautions This symbol alerts the user that important information regarding the installation and/or operation of this equipment follows. Information preceded by this symbol should be read carefully. This symbol alerts the user that the user manual and translated copies are published on the NDS website at: www.ndssi.com/user-manuals/ This symbol warns the user that un-insulated voltage within the unit may have sufficient magnitude to cause electrical shock. Do not touch any part inside the unit. To reduce the risk of electric shock, DO NOT remove the cover or back. Note: There are no user serviceable parts inside. Refer servicing to qualified service personnel. This symbol alerts the user that information preceded by this symbol should be read carefully to avoid damage to the equipment. This symbol denotes the manufacturer. This symbol denotes the manufacturer’s European Community representative. This symbol indicates compliance with the Waste Electrical and Electronic Equipment Directive (WEEE Directive). This symbol indicates the device is a Medical Device. This product is intended only for use by healthcare professionals in professional healthcare environments. This product is T.U.V. approved with respect to electric shock, fire and mechanical hazards only in accordance with CAN/CSA C22.2 No. 60601-1 and ANSI/AAMI ES60601-1. This product meets the requirements of EN60601-1 so as to conform to the 2017/745 Medical Device Regulation of European Union. Note: Any serious incident or adverse event that has occurred in relation to the device should be reported to the manufacturer and the competent authority of the Member State in which the user and/or patient is established. Federal (USA) law restricts this device to sale by or on the order of a physician.

Medical Device Shipping Symbols Medical device shipping symbols, as defined below are printed on the shipping containers used to transport this product. Position the

Keep dry

Fragile

Fragile keep dry

container up

Safety Information |ii

System Safety Requirements External equipment connected to the signal input/output or other connectors of this product for use in a patient environment must comply with the requirements of ISO and UL/EN/IEC 60601-1 safety standards. A person who connects such equipment to this product has by definition formed a system, and is responsible for compliance of that system to the same ISO and UL/EN/IEC 60601-1 safety standards. To prevent fire or shock hazards, do not expose this unit to rain or moisture.

Grounding This product is energized from an external electrical power source for 2017/745 Medical Device Regulation of European Union Class I equipment. It is the responsibility of the installer to test the product's earth ground to verify that it complies with the hospital, local and national impedance requirements. A ground post is located on the back of the product to use for grounding the chassis of the unit. Any such grounding must be installed in accordance with applicable electrical codes. This equipment/system is intended for use by healthcare professionals only. This product is a Class I medical device. No modifications are allowed. This product is intended for continuous operation.

Power Requirements Power Supply This product complies to the listed safety standards only when used with the supplied medical grade power supply: Model BridgePower BPM150S24F06 AC Input 100 - 240 Volts, 50 to 60 Hz DC Output 24 Vdc, 6.25 A, 150 W

Power Cord Use a hospital grade power cord with the correct plug for your power source. Disconnect the power cord from the AC mains. The power cord is the only recognized disconnect device. MEDICAL EQUIPMENT should be positioned so that the disconnect device is readily accessible. Monitors should be powered from a center tapped circuit when used in the US at voltages over 120 volts.

Intended Use and Contraindications Intended Use This product is intended for use in a medical environment to display high quality video and graphic images. Contraindications 1. Do not use this product in the presence of flammable anesthetics mixture with air, oxygen or nitrous oxide. 2. To prevent fire or shock hazards, do not expose this product to rain. 3. No part of this product may come in contact with a patient. Never touch the product and a patient at the same time. 4. This product is capable of displaying Radiology (PACS) images for reference only, and is not intended for diagnostic use. 5. For mission critical applications, we strongly recommend that a replacement unit be immediately available.

Image Retention Warning Warning: Leaving a fixed (constant) image on the monitor for a long period of time can result in image retention. Avoid leaving a fixed image on the monitor, or turn the monitor off when it is not in use.

iii| Safety Information

Terms and Conditions Declarations of Conformity FCC and Council Directives of European Standards This device complies with Part 15 of FCC rules and 2017/745 Medical Device Regulation of European Union. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesirable results. 1. Use the attached specified cables with the color monitor so as not to interfere with radio and television reception. Use of other cable and adapters may cause interference with other electronic equipment. 2. This equipment has been tested and found to comply with the limits pursuant to FCC part 15 and CISPR 11. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. IEC This equipment has been tested and found to comply with the limits for medical devices to the IEC 60601-1-2. These limits are designed to provide reasonable protection against harmful interference in a typical medical installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to other devices in the vicinity. FCC, Council Directives of European Standards, and IEC: There is no guarantee that interference will not occur in an installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult your dealer or an experienced radio/TV technician for help. Accessory equipment connected to this product must be certified according to the respective IEC Standards (i.e., IEC 60950-1 or IEC 62368-1) for data processing equipment and IEC 60601-1 for medical equipment. Furthermore, all configurations shall comply with the system standard, IEC 60601-1-1. Anyone who connects additional equipment to the signal input part or signal output part configures a medical system and is therefore responsible that the system complies with the requirements of system standard IEC 60601-1-1. Whoever is responsible for securing the unit to a system needs to ensure that the mounting equipment used with this product complies to IEC standard 60601-1. If in doubt, consult the technical services department or your local representative. FCC Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Terms and Conditions | iv

Legal Statement NDS may sell its products through other medical device manufacturers, distributors and resellers and therefore, purchasers of this NDS product should consult with the entity through which this product was originally purchased regarding the terms of any applicable product warranties provided by such entity, if any. NDS neither assumes nor authorizes any person to assume for it any other liabilities in conjunction with and/or related to the sale and/or use of its products. To ensure proper use, handling and care of NDS products, customers should consult the product specific literature, instruction manual, and/or labeling included with the product or otherwise available. Customers are cautioned that system configuration, software, the application, customer data and operator control of the system, among other factors, affect the product’s performance. While NDS products are considered to be compatible with many systems, specific functional implementation by customers may vary. Therefore, suitability of a product for a specific purpose or application must be determined by the consumer and is not warranted by NDS. NDS SPECIFICALLY DISCLAIMS ALL WARRANTIES OF ANY KIND, WHETHER EXPRESS, IMPLIED AND/OR STATUTORY, INCLUDING, BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, FITNESS AND/OR OF SUITABILITY FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT WITH RESPECT TO ALL NDS PRODUCTS OR SERVICES. ANY AND ALL OTHER WARRANTIES, REPRESENTATIONS AND/OR GUARANTEES, OF ANY TYPE, NATURE OR EXTENT, BE IT IMPLIED, EXPRESS AND/OR WHETHER ARISING UNDER OR AS A RESULT OF ANY STATUTE, LAW, COMMERCIAL USAGE, CUSTOM, TRADE OR OTHERWISE, ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED. NDS, its suppliers and/or distributors are not liable, directly or by way of indemnity for any special, incidental, consequential, punitive, exemplary or indirect damages, including but not limited to alleged damages for delayed shipment, non-delivery, product failure, product design or production, inability to use such products or services, loss of future business (lost profits), or from any other cause, whatsoever, in connection with or arising from the purchase, sale, lease, rental, installation or use of such NDS products, these terms and conditions, or with respect to any the terms of any agreement which incorporates these terms and conditions. SOME JURISDICTIONS DO NOT ALLOW EXCLUSIONS AND DISCLAIMERS OF CERTAIN WARRANTIES OR LIMITATIONS OF LIABILITY, SO THE LIMITATIONS AND/OR EXCLUSIONS, SET FORTH HEREIN, MAY NOT APPLY. IN THAT EVENT LIABILITY WILL BE LIMITED TO THE GREATEST EXTENT PERMITTED BY LAW IN THE SUBJECT JURISDICTION. The information provided in this document, including all designs and related materials, is the valuable property of NDS and/or its licensors and, as appropriate, they reserve all patent, copyright, and other proprietary rights to this document, including all design, manufacturing reproduction, use, and sales rights thereto, except to the extent said rights are expressly granted to others. This user manual is subject to change without notice. If there is any concern about the latest instructions for use, please consult with NDS.

v| Terms and Conditions

About This Manual

2

This manual is designed to assist the user with proper installation, setup and operation of the display. Depending on the model and options that were purchased, some of the features and options in this manual may not apply to the display you are using. A numbered tab on the side of the page denotes the beginning of a section.

Intended Use and Contraindications Intended Use: This monitor is intended for use in a medical environment to display high quality video and graphic images . Contraindications: The monitor may not be used in the presence of flammable anesthetics mixture with air, oxygen or nitrous oxide. No part of this product may come in contact with a patient. Never touch the product and a patient at the same time. This product is capable of displaying Radiology (PACS) images for reference, not diagnostic, purposes only. For mission critical applications, we strongly recommend that a replacement unit be immediately available.

Image Retention Notice Warning: Leaving a fixed (constant) image on the monitor for a long period of time can result in image retention ("burn in"). Avoid leaving a fixed image on the monitor’s screen or turn the monitor off when it is not in use.

Quick Startup Powering On The Unit: Connect the power supply to the display via the power plug. Plug in the AC adapter. Connect a video source to the display. Apply power to the peripheral device, then to the display. The NDS logo is displayed, followed shortly by video. The electronics, designed by NDS, incorporates proprietary SmartSync™ technology which at initialization, examines the incoming signal and automatically displays the video image in its proper format. This eliminates adjustments for most video sources. To fine tune the image, please refer to “Image Adjustments” on page 5. First time users and initial test: Visually, Flat-Panel (LCD) images will look crisper than those of a traditional CRT. For the same reason, live video may appear a little blocky. Users not familiar with the image differences should familiarize themselves before utilization in a critical application and determine its usability. It is recommended that first time users view the display next to a CRT to familiarize themselves with any subtle differences in viewing quality.

1

Connector Panels

3

Notes 1. An S-Video signal may be applied via 2 BNC terminated cables to the Y and C labeled BNC connectors or a DIN 4 terminated cable, but not both. 2. DVI 1 IN 1920 x 1200 maximum resolution. DVI 2 IN 1920 x 1080 maximum resolution. 3. 3G-SDI 1 and 3G-SDI 2 accept 3G-SDI signals. The provided accessory cable is not 3G-SDI compliant. 4. An RGBS, YPbPr or VGA signal may be applied via the DVI 2 connector or the R / Pr , G / Y / SOG 2, B / Pb and HS / C-SYNC BNC connectors. The VS BNC is used when the applied signal has both H sync and V sync. 5. Set the REDRIVE switch to Off when the RGBS and YPbPr signals will not be daisy chained to another display. The REDRIVE switch is set to On when the RGBS and YPbPr signals will be daisy chained to a second display. 6. DVI 1, 3G-SDI 1 and S-VIDEO re-drives are always active when the display is powered on. 7. FIBER OPTIC (90R0053 only) and DVI 1 inputs may be connected simultaneously, but may not be displayed simultaneously. 8. The ND-OS connector is used for installing BIOS upgrades. The ND-OS connector may also be used for controlling the display. See Communication Port on page 14.

2

Electrical Symbols Equipotentiality: This symbol appears next to the display’s Potential Equalization Conductor. (ground post) Open (Off) Switch: This symbol appears on the open, or off, side of the display’s rocker switch. Closed (On) Switch: This symbol appears on the closed, or on, side of the display’s rocker switch.

3

Control A 6 button keypad, located bottom center on the front of the display, allows the user to make adjustments to various display parameters using the On Screen Menu (OSM) system. To display the standard input menu, press the INPUT button twice.

4

Quick Select The QUICK SELECT menu, shown below, is displayed when the keypad’s INPUT button is pressed once. If the current input is one of the five shown in the QUICK SELECT menu, it will be illuminated. Select one of these inputs by pressing the keypad button under the QUICK SELECT key that points to it. For example: To select DVI-1, press the MENU button under the DVI-1 label. If a selection is not made the QUICK SELECT menu closes after 10 seconds. The QUICK SELECT menu closes 30 seconds after the last selection is made. Quick Select changes only the Primary input. If a Secondary input is being displayed and the input chosen with Quick Select is the same as the Secondary input, then the PIP image will be cleared and the chosen input will become the Primary input. Accessing the full input menu is described on page 7.

4

Image Adjustments Press this keypad button to adjust the Brightness, Contrast and / or the Backlight settings.

Adjust Brightness Press the Brightness / Contrast button to display the Brightness control. Press the ◄ or ► button to adjust Primary brightness. When a PIP image is visible, press the Brightness / Contrast button again to access the Secondary brightness control. Setting the brightness too high or too low will decrease the amount of visible grayscales.

Adjust Contrast Press the Brightness / Contrast button twice, three times when a PIP image is visible, to display the Contrast control. Press the ◄ or ► button to adjust Primary contrast. When a PIP image is visible, press the Brightness / Contrast button again to access the Secondary contrast control. Setting the contrast too high or too low causes loss of some grayscales. Color saturation may appear incorrect.

Adjust Backlight Press the Brightness / Contrast button three times, five times when a PIP image is visible, to display the Backlight control. Press the ◄ or ► button to set the backlighting. Note: Lowering the backlight level will increase the backlight lifetime.

5

Menu System Overview Press the MENU button once to open the On Screen Menu System (OSM). The primary and secondary inputs are shown at the top of the menu. The Picture menu is displayed when the OSM is opened. Press the ◄ or ► button to select the menu you want to work with, then press the SCROLL button to select the parameter. Press the ◄ or ► button to set the parameter to the desired value. Press the MENU button to save your changes and close the Menu System. Notes: 1. All parameter names change to the language selected in the Setup menu. 2. Grayed out parameters are not currently accessible.

5

Languages: English, Deutsch, Français, Italiano, Svenska, Español, Nederlands, Pycckий 6

Video Source Inputs Menu

Press the INPUT button twice to open the input menu. The Input menu shows a: P for primary input in the left most column and an: S for secondary input in the column to the right of the cursor. Press the SCROLL button to highlight the desired input. Finally, press ◄ button to make it the primary input or press ► to make it the secondary input. The secondary input may be cleared by highlighting it using the SCROLL button and pressing the ► button. Selecting a secondary input is optional. Note: Grayed out inputs are not accessible. The Input menu will automatically turn off 30 seconds after the most recent button press. It may also be turned off by pressing the Input button. The table below shows which inputs may be secondary when a given input is primary. Inputs marked with a √ in the secondary column may be designated as the secondary input. Inputs marked with an X in the secondary column may not be designated as the secondary input. The gray cells denote those inputs that share a common connector or common electronics and thus may not used simultaneously. DVI 2, RGBS, YPbPr and SOG 2 share the same input. Thus if one is selected as the primary input, the others may not be selected as secondary. The same is true for Composite, SOG 1 and VGA.

Secondary

Input

DVI 1

DVI Fiber

DVI 1 DVI Fiber SDI 1 P SDI 2 r

DVI 2

i

RGBS

m YPbPr a

S-Video

r

Composite

y

SOG 1 SOG 2 VGA

7

√ √ √ √ √ √ √ √ √ √

√ √ √ √ √ √ √ √ √ √

SDI 1

SDI 2

DVI 2

RGBS

YPbPr

SOG 2

S-Video

Composite

SOG 1

VGA

√ √

√ √ √

√ √ √ √

√ √ √ √

√ √ √ √

√ √ √ √

√ √ √ √ √ √ √

√ √ √

√ √ √

√ √ √

√ √ √

√ √ √ √ √ √ √ X

√ √ √ √ √ √ √ √

√ √

√ X

√ √ √ √ √ √ √ √ √ X √

√ √ √ √ √ √ √ √ √

√ √ √ √ √ √ √ √

√

√

√

√

X √ √ √

PIP and Swap

Selecting a secondary input will display a small image of the secondary source in the upper right corner of the display. Secondary Image Size Control The size of the secondary image is controlled by pressing ◄ or ► buttons. Pressing the ► button will cycle through: Small PIP = Width of secondary image is 25% of total screen width. Large PIP = Width of secondary image is 40% of total screen width. Split-Screen = Primary and Secondary have equal width side by side (half of screen width). Split-Screen Overscan = Primary and Secondary have equal width with overscan applied Full Screen Primary = No secondary image displayed. The images at the bottom of the page illustrate the above sequence. Pressing the ◄ button will cycle through the above sizes in reverse order. Pressing the SCROLL / SWAP button will exchange the primary and secondary inputs, and exchange their respective locations on the display. Pressing the button a second time will restore the inputs to their original primary/secondary status. It is not necessary for both images to be displayed in order to swap primary and secondary images. Secondary image size and image swapping may also be controlled via the GPIO port. GPIO details are on page 9 and the GPIO connector pin out is described on page 19.

Small PIP

Large PIP

Split Screen Overscan

Split Screen

Full Screen Primary

8

GPIO General Purpose Input Output (GPIO): The GPIO control allows the user to step through the Secondary image sizes as described on page 8, swap the Primary and Secondary images or display a Record indicator in the upper left corner of the display. Refer to the Input Menu shown below when setting up the Primary and Secondary inputs.

GPIO Primary / Secondary Source Setup: 1. Press the INPUT button twice to open the Input Menu. 2. Press the SCROLL button to highlight the input that will be designated as Primary. 3. Select it by pressing the ◄ button a P appears in the column to the left of the cursor. 4. After the Primary input is chosen you may designate a Secondary input. 5. Press the SCROLL button to highlight the input that will be designated as Secondary. 6. Select it by pressing the ► button an S appears in the column to the right of the cursor. The selected Secondary input appears as a small PIP in the upper right corner of the display. 7. The Secondary input may be cleared by highlighting it using the SCROLL button and pressing the ► button again. Using GPIO Control Fixture: 1. Connect an appropriately wired fixture to the GPIO connector. 2. Press the fixture’s PIP Size button. 3. The display will cycle through the PIP sizes. See page 8 for the sequence. 4. Press the fixture’s Swap button. The Primary and Secondary images swap locations 5. Press the fixture’s Record button, the Record indicator is displayed until the Record button is released. Note: GPIO connector pin out is on page 19.

Priority Input Select Setup: By default the Priority Input Select feature is enabled with the Primary (DVI) and Secondary (SDI) inputs preselected. If the Priority Input Select feature has been disabled, then a secondary input (pages 7 and 8) must be selected before the feature may be re-enabled. After selecting the secondary (PIP) input, press and hold the INPUT button for 3 seconds. When the Priority Input Select feature becomes active, a “Priority Input Select On” message appears in the middle of the screen for about 2 seconds, the PIP image is placed behind the primary, the PIP + and - (◄ and ►) buttons are disabled, and the SWAP button remains enabled. When Priority Input Select is enabled, holding the INPUT button down for 3 seconds disables it. Operation: When Priority Input Select is enabled and the primary signal is lost, the secondary input becomes the displayed image. If the primary signal is restored, its image becomes the displayed image again, and the secondary image is placed behind the primary image. If both the primary and secondary signals are lost, the monitor alternately scans the primary and secondary inputs until a signal is detected on one of them. When a signal is detected on the primary or secondary input, its image is displayed on the monitor.

9

Display Setup HD-SDI Picture Menu

SD-SDI, S-Video and Composite Picture Menu

Horizontal Position (SD-SDI, S-Video and Composite only): This control is disabled when Overscan is set to 0. Moves the image to the left or right. Press ◄ or ► to horizontally center the image. Vertical Position (SD-SDI, S-Video and Composite only): This control is disabled when Overscan is set to 0. Moves the image up or down. Press ◄ or ► to vertically center the image. Sharpness: Press ◄ or ► to adjust the sharpness (focus) of the displayed image. Overscan: 0 = The image is displayed at a size that fills the screen without losing any video information. The image presented to the display may include black bars top and bottom or left and right. 1, 2, 3, 4, 5 or 6 = The image is linearly enlarged, while remaining centered, in incremental steps. As the image becomes larger video information will be lost from the top and bottom and / or left and right. Select using ◄ or ► buttons. Aspect (SD-SDI, S-Video and Composite only): Pressing the ◄ or ► button changes the aspect ratio of the image from 4:3 to 16:9 or from 16:9 to 4:3. Note: Displaying a 4:3 image in 16:9 causes its elements stretched horizontally. Likewise, displaying a 16:9 image in 4:3 causes its elements to be compressed horizontally. Mirroring: Pressing the ◄ or ► button presents the displayed image swapped from right to left and displays a mirroring indicator in the lower right corner. Pressing the ◄ or ► button again returns the image to its normal left to right orientation and removes the mirroring indicator 10

VGA,SOG, RGBS and YPbPr Picture Menu

Horizontal Position: Moves the image to the left or right. Press ◄ or ► to horizontally center the image. Vertical Position: Moves the image up or down. Press ◄ or ► to vertically center the image. Sharpness: Press ◄ or ► to adjust the sharpness (focus) of the displayed image. Phase: Press ◄ or ► to adjust the phase of the display’s pixel clock. Frequency: Adjusts the frequency of the display’s pixel clock. With Scaling set to Fill adjust until image just fills the screen horizontally. Press ◄ or ► to adjust the frequency of the display’s pixel clock. Overscan (Video): This parameter is enabled when the input is 16:9 or 480P or 576P or interlaced. 0 = The image is displayed at a size that fills the screen without losing any video information. The image presented to the display may include black bars top and bottom or left and right. 1, 2, 3, 4, 5 or 6 = The image is linearly enlarged, while remaining centered, in incremental steps. As the image becomes larger video information will be lost from the top and bottom and / or left and right. Select using ◄ or ► buttons. Scaling (Graphics): This parameter is enabled when the input signal is not 16:9, not interlaced and not 480P or 576P. Fill = Expands the video image to fill the entire screen. The aspect ratio may not be accurately displayed. Aspect = Expands the video image until its largest dimension fills the screen. Image may be displayed with black bars on the top and bottom or the left and right. 1:1 = Displays the video data in its native size and aspect ratio. Image may be displayed with black bars on the top and bottom and on the left and right. Select using ◄ or ► buttons. SmartSync™ / Alternative Modes On initialization NDS’ proprietary SmartSync technology examines the incoming signal and automatically displays the video image in its proper format. To run SmartSync highlight the SmartSync / Alternative Modes parameter and press the ◄ button. To select an alternate mode (format) highlight the SmartSync / Alternative Modes parameter and press the ► button. The mode increments each time the ► button is pressed until the selected mode equals the maximum available, the next time ► pressed the first mode is restored. Alternative Modes are used to manually distinguish between modes (resolutions) whose timing characteristics are very close. Mirroring: Pressing the ◄ or ► button presents the displayed image swapped from right to left and displays a mirroring indicator in the lower right corner. Pressing the ◄ or ► button again returns the image to its normal left to right orientation and removes the mirroring indicator 11

DVI Digital Picture Menu

Overscan (Video) This parameter is enabled when the input is 16:9 or 480P or 576P or interlaced. 0 = The image is displayed at a size that fills the screen without losing any video information. The image presented to the display may include black bars top and bottom or left and right. 1, 2, 3, 4, 5 or 6 = The image is linearly enlarged, while remaining centered, in incremental steps. As the image becomes larger video information will be lost from the top and bottom and / or left and right. Select using ◄ or ► buttons. Scaling (Graphics) This parameter is enabled when the input signal is not 16:9, not interlaced and not 480P or 576P. Fill = Expands the video image to fill the entire screen. The aspect ratio may not be accurately displayed. Aspect = Expands the video image until its largest dimension fills the screen. Image may be displayed with black bars on the top and bottom or the left and right. 1:1 = Displays the video data in its native size and aspect ratio. Image may be displayed with black bars on the top and bottom and on the left and right. Select using ◄ or ► buttons. Mirroring: Pressing the ◄ or ► button presents the displayed image swapped from right to left and displays a mirroring indicator in the lower right corner. Pressing the ◄ or ► button again returns the image to its normal left to right orientation and removes the mirroring indicator

12

Color Menu

Gamma: Press ◄ or ► to select a preset Gamma (1.8, 2.0, 2.2, 2.4 or 2.6), Video or PACS Notes: 1. Video is a color corrected Look Up Table (LUT). 2. PACS is a DICOM-like LUT. Note: This product is capable of displaying Radiology (PACS) images for reference, not diagnostic, purposes only. Color Temperature: Press the ◄ or ► button to select a preset color temperature. Note: When a preset is selected and any parameter is changed, the current values are copied to the User presets and User is selected. Red, Green, Blue: Press the ◄ or ► button to increase or decrease the intensity of the selected color. Saturation: Press ◄ or ► to set the saturation (color intensity) of the image. Hue: Press ◄ or ► to set the hue (color tint) of the image. Brightness: Press the ◄ or ► button to adjust brightness. This is a duplicate of the Brightness control described on page 5. Contrast: Press the ◄ or ► button to adjust contrast. This is a duplicate of the Contrast control described on page 5. Video Level: Normal: Provides a dynamic range equivalent to the incoming signal with no change. Expanded: Expands the signal level such that an input signal with range 16 (black) to 235 (white) will be expanded to a range of 0 (black) to 255 (white). Note: If a signal is already full range (0 to 255), changing the setting to Expanded will cause the signal to “clip” or “saturate”. Press the ◄ or ► button to select.

13