Norav Medical

Norav Stress Testing System

Norav NBP 24 NG PC Analysis Software Short Guide May 2011

Short Guide

2 Pages

Short Guide ABDM System Norav NBP-24 NG PC Analysis Software NHMS Software (For further instructions please take a look at the user manual)  1. Function Keys  2. Preparing the measurement Ÿ Open the Norav Hypertension-Management-System Software (NHMS Software) on your PC and insert new batteries into  the monitor. In case you work with rechargeable batteries, please make sure that the batteries used are fully recharged Ÿ Interface Cable: Connect the PC with the monitor by plugging the cable from the PC into the side socket of the monitor  (red dot to red dot). Switch on the recorder (On/Off). “co” will appear on the display of the monitor. Ÿ Interface Infrared: When working with the IR-Interface “IR-Med”, first open the interface menu of the monitor by pressing  and holding the “Start”- Key and then pressing the “Day/Night”- Key. You are now able to select between “co”, “bt” and “PAIr” by pressing the “Start”- Key. Select “co” and confirm with the “Event”- Key. The letters “co” will stop blinking and the interface is being activated. Now align the IR-Interface of the monitor to the IR-Interface “IR-Med”, which is connected to the PC. The preferable distance between both IR-Interfaces is 10 - 15 cm. Ÿ Start the Norav Software on your computer Ÿ You can now either create a new patient using the  button or select an already existing patient by pushing the  button. Confirm with “OK”. Ÿ Choose the function  to prepare the monitor.  Ÿ Interface Bluetooth: The following step is to be processed only once for a new device.  Start the NHMS Software on your computer. Select the menu Settings/Port settings/Bluetooth and click on “Add device”. Open the interface menu of the monitor by pressing and holding the “Start“- Key and then pressing the “Day/Night”- Key . You are now able to select between “co”, “bt” and “PAIr” by pressing the “Start”- Key. Select “PAIr” and confirm with the “Event”- Key . The letters “PAIr” will stop blinking. Press the “OK” button in the software. Now all Bluetooth devices in the surrounding will be detected and displayed on your computer. The NBP-24 NG can be recognized by the S/N (e.g. C00511), which will be equivalent to the number on the back side of the device. Select the S/N in the software and click on “Pairing”. After a short beep, the one-time pairing process (connection between NBP-24 NG and NHMS Software) is accomplished. For future use you just need to open the NHMS Software, create a patient with the patient with the  Button or select a pre-existing  Button. Now open the Interface menu of the monitor by pressing and olding the “Start”- Key  and then pressing the “Day/Night”- Key . You are able to select between “co”, “bt” and “PAIr” by pressing the “Start”Key. Select “bt” and confirm with the “Event”- Key . The letters “bt” will stop blinking and the Bluetooth interface is being activated. After a few seconds there will appear a window on your computer with following menu options: “Prepare device”, “Read-out of values” and “Cancel”. Select “Prepare device”. Ÿ Should the battery voltage be too low, a warning will appear. Change batteries if neccessary.  Ÿ In the upcoming window, you can choose a preset protocol or you can configure protocols 1 and 2 according to your  needs. Ÿ Set the “Clock of the device” by pushing the corresponding button on the upper right side of the menu window. Ÿ Press the menu button Ÿ With the button  . you will send and activate the selected protocol to the monitor.  Norav Medical GmbH 02.05.2011
File Type: PDF
File Size: 398 KB
File Name: norav_nbp_24_ng_pc_analysis_software_short_guide_ma.pdf

By clicking Download you are confirming this is the correct document for your purposes
and that you agree to our Terms & Conditions