PHYSIO CONTROL
Beds, Chairs, Stretchers and Stools
M-Series Stretcher Model SM104 (1007) Maintenance Manual Rev A Sept 2006
Maintenance Manual
168 Pages
Preview
Page 1
Mai nt enance Manual
Medi cal
MSer i esSt r et cher ModelSM104 I mpor t ant I nf or mat i on Fi l ei ny our ma i nt ena nce r ecor ds
Forpar t sort echni cal assi st ancecal l 8003270770( opt i on2)
Table of Contents Introduction Specifications... 4 Warning / Caution / Note Definition... 4 Summary of Safety Precautions... 5 Symbols... 6 Preventative Maintenance Checklist... 7 Cleaning... 8−9 Service Information Caster Cover Installation and Removal... 10 Caster Removal... 10 Brake Rod Removal... 11 Side Control Brake Rod Removal... 11 Release Pedal Adjustment... 12 Foot End Release Pedal Replacement... 12 Foot End Release Pedal Rod Removal... 12 Brake Ring Removal... 13 Fifth Wheel Assembly Removal... 13 Litter Top Removal... 14 Jack Descent Rate Adjustment... 14 Removal of Excess Air from the Hydraulic System... 14 Head End Hydraulic Jack Removal... 15 Foot End Hydraulic Jack Removal... 15 Gatch Release Handle Replacement... 16 Gatch Valve Body Replacement... 16 Siderail Assembly Removal and Replacement... 16−17 Pneumatic Cylinder Replacement... 18 Litter Corner Cover Replacement... 18 IV Pole Replacement... 19 Oxygen Bottle Holder Replacement... 19 Static Discharge Precautions... 20 Scale Display Box Replacement... 21 Scale Display Cover Replacement... 22 Scale Display Lens Replacement... 22 Scale Display Battery Holder Replacement... 23 Load Cell Replacement... 24 Scale System Diagnostics... 25−26 Scale System Batteries... 26 Quick Reference Replacement Parts List... 27−28
Table of Contents Assembly Drawings and Parts Lists Fifth Wheel Base Assembly... 29 Fifth Wheel Assembly... 30−31 Standard Brake Assembly... 32−33 Brake Rod Assembly... 34 Drive Link Assembly... 35−36 Caster Assembly... 37 Side Control Brake Assembly... 38−40 Brake Rod/Side Control Assembly... 41 Side Control Brake Sub−Assembly... 42 Standard Brake Assembly, Colored Components... 43 Side Control Brake Assembly, Colored Components... 43 Dual Side Hydraulics Assembly... 44−46 Standard Hydraulics Assembly, Colored Components... 47 End Control Hydraulics Assembly, Colored Components... 47 Lowering Pedal Assembly... 48 Head End Pump Pedal Assembly... 49 3−Sided Hydraulics Assembly... 50−51 Foot End Release Pedal Assembly... 52 Foot End Pump Pedal Assembly... 53 Jack Base Assembly... 54 Constant Descent Jacks... 55 Constant Descent Jack Assembly... 56 Base Labeling, Standard Brakes and Hydraulics... 57−58 Base Labeling, 4−Sided Brakes / Standard Hydraulics... 59−60 Base Labeling, Standard Brakes / 3−Sided Hydraulics... 61−62 Base Labeling, 4−Sided Brakes / 3−Sided Hydraulics... 63−64 Base Labeling Assembly, Department Labels... 65 Litter Assembly... 66−67 Siderail Assembly... 68−69 Siderail Latch Assembly... 70−71 Siderail Spindle Assembly... 72−73 Siderail Latch Spindle Assembly... 74−75 Dual Siderail Latch Assembly... 76−77 Latch Assembly... 78−81
Table of Contents Assembly Drawings and Parts Lists (Continued) Standard Fowler/Stationary Foot Assembly... 82−83 Standard Fowler/Knee Gatch Assembly... 84−87 Standard Fowler Assembly... 88−91 Seat Section Assembly... 92−93 Knee Gatch Assembly... 94−97 Gatch Valve Body Assembly... 98 Gatch Cylinder/Hose Assembly... 99 Gatch Pump Assembly... 100 Gatch Release Handle Assembly... 101 Thigh Section Assembly... 102−103 Calf Section Assembly... 104−105 Drop Seat Fowler/Stationary Foot Assembly... 106−109 Drop Seat Fowler Assembly... 110 Drop Seat Fowler/Knee Gatch Assembly... 112−115 Corner Cover Assembly... 116−119 Slider Board Assembly... 120−121 Monitor Tray... 122−123 Push Handle Assembly... 124 No Push Handle Option... 125 Scale Option − 26” Litter with Stationary Foot Section... 126−128 Scale Option − 26” Litter with Knee Gatch... 129−131 26” Scale Lift Header... 132−133 Scale Option − 30” Litter with Stationary Foot Section... 134−136 Scale Option − 30” Litter with Knee Gatch... 137−139 30” Scale Lift Header... 140−141 Scale Display Assembly... 142−143 I.V. Poles... 144−152 Oxygen Bottle Holders... 153−157 Defibrillator Tray Assembly... 158 Defibrillator Tray/Foot Extender/Foot Board Assembly... 159 Serving Tray Assembly... 160 Foot Board/Serving Tray Holder... 161 Foot Board/Chartholder Assembly... 162 Mattresses and Siderail Pads... 163−164 Warranty Obtaining Parts and Service... 165 Service Contract Coverage... 165 Return Authorization... 166 Freight Damage Claims... 166
Introduction INTRODUCTION This manual is designed to assist you with the maintenance of the Model SM104 Stretcher. Read it thoroughly before using the equipment or beginning any maintenance on it.
SPECIFICATIONS Maximum Weight Capacity
700 pounds
Overall Stretcher Length
84” ( .5”)
Overall Stretcher Width (Siderails Up)
33.5” & 37” ( .5”)
Overall Stretcher Width (Siderails Down)
30.25” & 30.75” ( .5”)
Minimum / Maximum Bed Height
20.75” / 34” ( .5”)
Fowler Angle
0 to 90° (
3°)
Knee Gatch Angle
0 to 40° (
1°)
Trendelenburg / Reverse Trendelenburg
+16 / −16 ° (
Minimum Under Stretcher Clearance
6” (15 cm) nominal 1.75” (4.5 cm) under the hydraulic cyclinders and 5th wheel 0 lbs. to maximum capacity of the stretcher
Optional Scale System Weight Operating Range Optional Scale System Accuracy
1°)
Between 10° Trend & 10° reverse Trend* 2 lbs. of weights below 100 lbs. 2% of weights above 100 lbs.
Optional Scale System Environmental Requirements for Operation
60_ F − 80_ F 0% − 90% Relative Humidity
* Scale does not meet accuracy claims at Trend angles outside the specified range. Stryker reserves the right to change specifications without notice.
WARNING / CAUTION / NOTE DEFINITION The words WARNING, CAUTION and NOTE carry special meanings and should be carefully reviewed. WARNING Alerts the reader about a situation, which if not avoided, could result in death or serious injury. It may also describe potential serious adverse reactions and safety hazards. CAUTION Alerts the reader of a potentially hazardous situation, which if not avoided, may result in minor or moderate injury to the user or patient or damage to the equipment or other property. This includes special care necessary for the safe and effective use of the device and the care necessary to avoid damage to a device that may occur as a result of use or misuse. NOTE This provides special information to make maintenance easier or important instructions clearer.
Return to Table of Contents
4
Summary of Safety Precautions Before operating this stretcher, it is important to read and understand all information in this manual. Carefully read and strictly follow the warnings and cautions listed on this page.
WARNING Always apply the caster brakes when a patient is getting on or off the stretcher. Push on the stretcher to ensure the brakes are securely locked. Always engage the brakes unless the stretcher is being moved. Injury could result if the stretcher moves while a patient is getting on or off the stretcher. When lowering the siderail to the collapsed position, keep extremities of patients and staff away from the siderail spindles or injury could occur. Keep fingers/hands clear of area around Fowler release handle and Fowler frame when lowering. Injury could result if care is not taken when lowering the Fowler. If the stretcher is equipped with the optional foot end IV pole, the IV pole must be in the raised position when the foot extension/defibrillator tray is installed. If the IV pole is not raised, the foot extension will not function properly and injury could occur.
CAUTION To avoid damage, remove any equipment that may be in the way before raising or lowering the litter height. To avoid injury or damage to the equipment, do not allow the siderail to lower on its own. To avoid damage, the weight of the I.V. bags should not exceed 40 pounds. To avoid damage while transporting the stretcher, verify the I.V. pole is at a low enough height to allow it to safely pass through door openings and under light fixtures. The weight capacity of the Knee Gatch is 200 pounds. Do not sit or stand on the Gatch. Injury or damage to the equipment could occur. To avoid damage, do not put items weighing more than 30 pounds on the serving tray. The unit cannot be raised (hydraulics on base) with a patient lift under the stretcher. The hood may not be used for stepping. Note Clean hood storage area regularly. The bottom of the brake rings should be cleaned regularly to prevent wax and/or floor remnant buildup.
Return to Table of Contents
5
Symbols OPTIONAL SCALE SYSTEM
Warning, Refer to Service/Maintenance Manual Internally Powered Mode of Operation: Continuous IPX5 Electromagnetic Interference − product conforms to IEC 60601−1−2:1993 − Class B Type: 4 x AA Battery (4 x 1.5VDC) Voltage: 6.0VDC Medical Equipment Classified by Underwriters Laboratories Inc. with Respect to Electric Shock, Fire, Mechanical and Other Specified Hazards Only in Accordance with UL 2601−1 and CAN/CSA C22.2 No. 601.1 UL60601−1 CAN/CSA C22.2 NO.601.1
Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygen or nitrous oxide.
Safe Working Load
Return to Table of Contents
6
Preventative Maintenance CHECKLIST All fasteners secure Siderails move and latch properly Engage brake pedal and push on the stretcher to ensure all casters lock securely Steer function working properly All casters secure and swivel properly Body restraints working properly IV pole intact and operating properly Oxygen bottle holder intact and operating properly Fowler operating and latching properly Knee Gatch operating properly (optional equipment) Trendelenburg/Reverse Trendelenburg operating properly No rips or cracks in mattress cover Ground chain intact No leaks at hydraulic connections Hydraulic jacks holding properly Hydraulic drop rate set properly Hydraulic oil level sufficient Lubricate where required Accessories and mounting hardware in good condition and working properly No cables worn or pinched (optional scale system) All electrical connections tight (optional scale system) All grounds secure to the frame (optional scale system) Batteries sufficiently charged (optional scale system) Display housing intact and not damaged (optional scale system) Display label intact and not damaged (optional scale system) Load cells intact and not damaged (optional scale system) Scale calibrated properly. Recalibrate, if necessary (optional scale system)
Serial No. ______________
______________
______________
______________
______________
______________
Completed By:_________________________________
Date:_____________
NOTE Preventative maintenance should be performed at a minimum of annually. A preventative maintenance program should be established for all Stryker Medical equipment. Preventative maintenance may need to be performed more frequently based on the usage level of the product.
Return to Table of Contents
7
Cleaning CLEANING Model 1005 stretchers are designed to be power−washable. The unit may show some signs of oxidation or discoloration from continuous washing. However, no degradation of the stretcher’s performance characteristics or functionality will occur due to power washing as long as the proper procedures are followed. S
Follow the cleaning solution manufacturer’s dilution recommendations exactly.
S
Remove the mattress prior to washing the unit; do not wash the mattress with the stretcher.
S
Position the Fowler at 45_, place the unit in full reverse Trendelenburg (foot end down), raise the siderails, and place the I.V. poles and push handles in the up position.
S
Stryker Medical recommends the standard hospital surgical cart washer for power washing Model 1005 stretchers.
S
Do not replace the mattress on the stretcher until the unit is completely dry.
S
Before returning the unit to service, verify all labels are intact, verify the brake/steer pedal locks properly in both positions and check all components for proper lubrication.
DO NOT STEAM CLEAN THE UNIT. Use a maximum water temperature of 180_F/82_C. Maximum air dry temperature (cart washers) is 240_F/115_C. Water pressure − 1500 psi/103.5 bar. If a hand held wand is being used to wash the unit, the pressure nozzle must be kept a minimum of 24 inches/.61m from the unit. Stretchers must have maintenance performed after a minimum of every fifth washing. Refer to the maintenance manual for specific lubrication instructions. Failure to comply with these instructions may invalidate any/all warranties. Do not use abrasive cleaners to clean the display enclosure for the optional scale system. Do not allow cleaning solutions or other fluids to pool on the display unit. Wipe dry all surfaces after spills or cleaning.
Return to Table of Contents
8
Cleaning CLEANING (CONTINUED) In general, when used in those concentrations recommended by the manufacturer, either phenolic type or quaternary type disinfectants can be used. Iodophor type disinfectants are not recommended for use because staining may result. The following products have been tested and have been found not to have a harmful effect WHEN USED IN ACCORDANCE WITH MANUFACTURERS RECOMMENDED DILUTION.*
TRADE NAME
DISINFECTANT TYPE
MANUFACTURER
*MANUFACTURER’S RECOMMENDED DILUTION
A33
Quaternary
Airwick (Professional Products Division)
2 ounces/gallon
A33 (dry)
Quaternary
Airwick (Professional Products Division)
1/2 ounce/gallon
Beaucoup
Phenolic
Huntington Laboratories
1 ounce/gallon
Blue Chip
Quaternary
S.C. Johnson
2 ounces/gallon
Elimstaph
Quaternary
Walter G. Legge
1 ounce/gallon
Franklin Phenomysan F2500
Phenolic
Purex Corporation
1 1/4 ounce/gallon
Franklin Sentinel
Quaternary
Purex Corporation
2 ounces/gallon
Galahad
Phenolic
Puritan Churchill Chemical Company
1 ounce/gallon
Hi−Tor
Quaternary
Huntington Laboratories
1/2 ounce/gallon
LPH
Phenolic
Vestal Laboratories
1/2 ounce/gallon
Matar
Phenolic
Huntington Laboratories
1/2 ounce/gallon
Omega
Quaternary
Airwick (Professional Products Division)
1/2 ounce/gallon
Quanto
Quaternary
Huntington Laboratories
1 ounce/gallon
Sanikleen
Quaternary
West Chemical Products
2 ounces/ gallon
Sanimaster II
Quaternary
Service Master
1 ounce/gallon
Vesphene
Phenolic
Vestal Laboratories
1 1/4 ounce/ gallon
Quaternary Germicidal Disinfectants, used as directed, and/or Chlorine Bleach products, typically 5.25% Sodium Hypochlorite in dilutions ranging between 1 part bleach to 100 parts water, and 2 parts bleach to 100 parts water are not considered mild detergents. These products are corrosive in nature and may cause damage to your stretcher if used improperly. If these types of products are used to clean Stryker patient handling equipment, measures must be taken to insure the stretchers are rinsed with clean water and thoroughly dried following cleaning. Failure to properly rinse and dry the stretchers will leave a corrosive residue on the surface of the stretcher, possibly causing premature corrosion of critical components. NOTE Failure to follow the above directions when using these types of cleaners may void this product’s warranty.
REMOVAL OF IODINE COMPOUNDS This solution may be used to remove iodine stains from mattress cover and foam footrest pad surfaces. 1. Use a solution of 1−2 tablespoons Sodium Thiosulfate in a pint of warm water to clean the stained area. Clean as soon as possible after staining occurs. If stains are not immediately removed, allow solution to soak or stand on the surface. 2. Rinse surfaces which have been exposed to the solution in clear water before returning bed to service.
Return to Table of Contents
9
Service Information CASTER COVER INSTALLATION AND REMOVAL
1. Double Prongs
Single Prong
Looking through the larger of the two side cut−outs, align the cover with the axle nut or bolt head, as shown. Push down on the opposite side of the cover until the single prong engages the caster horn.
Top View (Cut−Away)
2.
Push on the cover with your palm until the double prongs engage.
Properly Attached Cover
Top View (Cut−Away)
3.
To remove the wheel cover, insert a large screwdriver into the cut−out in the side of the wheel cover and into the space between the double prongs. Pry up the cover to disengage the double prongs and push sharply upward to disengage the single prong.
Top View (Cut−Away)
CASTER REMOVAL Required Tools: 9/16” Open End Wrench 1. Remove the caster cover. 2. While keeping pressure on the caster bolt with your index finger, use a 9/16” open end wrench to remove the nylock hex nut on top of the caster assembly. 3. Using the brake ring, lift up on the base assembly and pull the caster assembly down to remove it. 4. Reverse steps 1−3 to install the new caster.
Return to Table of Contents
10
Service Information BRAKE ROD REMOVAL Required Tools: Hammer
7/32” Punch
String or Bungee Cords
1. Pump the litter up to full height. 2. Lift the base hood and support it from the litter using string or bungee cords. 3. Remove the hex head cap screws connecting the brake rod supports to the base frame. 4. Remove the bolt connecting the drive link assembly to the fifth wheel cam. 5. Remove the rue ring cotter and clevis pin connecting the rod end link to the side control link. 6. Remove the rue ring cotter connecting the drive link assembly to the bearing pivot support on the base frame (under the brake ring weldment). 7. Remove the three hex washer head screws holding the brake rod assembly to the base frame. 8. Remove the slotted spring pins connecting the butterfly “V” pedals, drive link assemblies and side control link to the brake rod. 9. Reverse steps 1−8 to reinstall the brake rod. When reinstalling the brake rod supports, torque the hex head cap screws to 5−13 ft.−lbs. CAUTION When reattaching the brake rod assembly to the base frame, set the torque specs no higher than 13 ft.−lbs. or damage could occur to the bolts.
SIDE CONTROL BRAKE ROD REMOVAL Required Tools: Hammer
7/32” Punch
Needle Nose Pliers
String or Bungee Cords
1. Pump the litter up to full height. 2. Lift the base hood and support it from the litter using string or bungee cords. 3. Remove the rue ring cotter and clevis pin connecting the rod end link to the side control link. 4. Remove the four bolts holding the brake rod assembly to the base frame and remove the entire assembly. 5. Using a hammer and 7/32” punch, drive the slotted spring pin out of the butterfly “V” pedal on the patient’s left side and remove the pedal, 6. Using a hammer and 7/32” punch, drive the slotted spring pin out of the hard stop in the center of the support weldment. 7. Using a hammer and 7/32” punch, drive out the slotted spring pin connecting the side control link to the side control brake rod on the patient’s right side. 8. Pull on the butterfly “V” pedal on the patient’s right side to remove the side control brake rod from the base. 9. Reverse steps 1−8 to reinstall the brake rod. When reinstalling the assembly, torque the hex head cap screws to 5−13 ft.−lbs. CAUTION When reattaching the brake rod assembly to the base frame, set the torque specs no higher than 13 ft.−lbs. or damage could occur to the bolts.
Return to Table of Contents
11
Service Information RELEASE PEDAL ADJUSTMENT 1. Manually disengage the release pedal swivel (item H on page 45) from the release pedal assembly. 2. To increase the release rod engagement with the release valve, turn the release pedal swivel clockwise on the threaded release rod. 3. To decrease the release rod engagement with the release valve, turn the release pedal swivel counterclockwise on the threaded release rod. NOTE If the pedal swivel assembly is threaded too far onto the release rod, the release valve will be partially activated and the jack will drift.
FOOT END RELEASE PEDAL REPLACEMENT Required Tools:
Needle Nose Pliers
1. Apply the stretcher brakes. 2. Disconnect the release pedal return springs from the foot end release pedals. 3. Remove the rue ring cotters and the clevis pins connecting the foot end release pedals to the mounting bracket. 4. Rotate the pedals upward. 5. Remove the rue ring cotters connecting the head end and foot end release rods to the foot end release pedals and remove the pedals. 6. Reverse steps 2−5 to install the new pedals.
FOOT END RELEASE PEDAL ROD REMOVAL Required Tools:
Needle Nose Pliers
1. Remove the foot end release pedal (see procedure above). 2. Remove the snap in nyliners holding the foot end pedal release rods in the pedal mounting bracket. 3. Unsnap the foot end pedal release rods from the white plastic release rod brackets. 4. Dislodge the side control release pedal swivels from the studs on the side control release pedal weldments. 5. Remove the foot end pedal release rods. 6. Reverse steps 1−5 to reinstall the pedal rods.
Return to Table of Contents
12
Service Information BRAKE RING REMOVAL Required Tools: 9/16” Socket w/Extension
3/8” Drive Ratchet
Needle−Nose Pliers
String or Bungee Cord
1. Pump the litter up to full height. 2. Lift the base hood and support it from the litter using string or bungee cords. 3. Using needle−nose pliers, unhook the extension springs from the top of the base caster tubes. 4. Remove the plastic caster covers. 5. While putting pressure on the caster carriage bolt, use a 9/16” socket and a 3/8” drive ratchet to remove the caster nut on both sides of the stretcher. 6. Remove the casters. 7. Remove the brake rod (see procedure). 8. Remove the cotter pin from the clevis pin in the center of the brake ring weldment. 9. Remove the cotter pin from the bearing pivot support. 10. Remove the 3/4” nylock hex nut from the bearing pivot support. 11. Remove the drive link assembly. 12. Pull the brake ring down and out away from the stretcher base frame. 13. Reverse steps 1−12 to reinstall the brake ring.
FIFTH WHEEL ASSEMBLY REMOVAL Required Tools: 1/2” Socket
3/8” Drive Ratchet
1. Using a 1/2” socket and 3/8” drive ratchet, remove the 1/2” bolt holding the fifth wheel cam drive link and fifth wheel drive link to the fifth wheel cam. 2. Remove the two 1/2” bolts holding the fifth wheel mounting bracket to the base frame weldment. 3. Remove the fifth wheel assembly. 4. Reverse steps 1 and 2 to reinstall the fifth wheel. When reinstalling the assembly, torque the hex head cap screws to 5−13 ft.−lbs. CAUTION When reattaching the fifth wheel assembly to the base frame, set the torque specs no higher than 31 ft.−lbs. or damage could occur to the bolts.
Return to Table of Contents
13
Service Information LITTER TOP REMOVAL Required Tools:
1/2” Socket w/Extension
3/8” Drive Ratchet
Standard Screwdriver
1. Using the foot pedal, pump up the litter top to full height. 2. Remove the stretcher mattress 3. Using a 1/2” socket, and a 3/8” drive ratchet, remove the truss head screws holding the jack support tubes to the jack shafts. 4. Thread a 7/16−20 fine thread bolt far enough into the top of the jack supports to separate the litter top from the jack shaft. 5. With the assistance of another person, lift the litter straight up to remove it from the jack shafts and set it aside.
JACK DESCENT RATE ADJUSTMENT Required Tools: Screwdriver
Bungee Cords (or equivalent)
Adjustment Procedure: 1. Pump the litter up to full height. 2. Lift the base hood, separating the hood from the base frame. Support the hood from the litter using bungee cords so it is out of the way. 3. The descent rate needle valve is located on the base of the jack. Turning the needle valve clockwise, with a screwdriver, will decrease the rate of descent. Turning it counterclockwise will increase the rate of descent. NOTE The larger percentage of a patient’s weight is located in the torso area. Adjust descent rate accordingly. 4. Remove the bungee cords supporting the base hood and secure the hood to the base frame. NOTE The jack descent rate is preset at the factory and adjustment is not recommended.
REMOVAL OF EXCESS AIR (VACUUM) FROM THE HYDRAULIC SYSTEM 1. Verify all hydraulic linkages are secure and operating properly. 2. Using the pump pedal, actuate the system several times to force the air through the system. The jack should now raise properly.
Return to Table of Contents
14
Service Information HEAD END HYDRAULIC JACK REMOVAL Required Tools:
1/2” Socket w/Extension
3/8” Drive Ratchet
1. Remove the litter top from the stretcher (see page 14). 2. Using a 1/2” socket with extension and a 3/8” drive ratchet, remove the two hex head screws holding the jack base to the stretcher base frame. 3. Remove the two hex head screws holding the jack reservoir clamp to the base frame and remove the clamps. 4. Lift straight up on the pump connecting rod and disconnect the pump piston from the connecting rod. 5. Disconnect the pump pedal swivel from the release pedal mounting plate. 6. Remove the head end release rod from the release valve assembly. 7. Using a 1/2” socket with extension and a 3/8” drive ratchet, remove the two hex head screws holding the jack base to the stretcher base frame. 8. Lift out the jack assembly. 9. To reinstall the jack, install the bolts on the jack and reservoir clamp but do not tighten them fully. 10. Reinstall the pump connecting rod and release rod. 11. Depress the pump pedal fully (to the floor). This will properly locate the jack onto the base frame. 12. Tighten the bolts on the jack and reservoir clamp. 13. Pump up the litter and apply weight to verify the jacks hold and do not drift. NOTE The jack descent rate is preset at the factory and adjustment is not recommended.
FOOT END HYDRAULIC JACK REMOVAL (BASE WITH DUAL CONTROLS) Required Tools: 1/2” Socket
3/8” Drive Ratchet
Pliers
1. Remove the litter top from the stretcher (see page 14). 2. Lift the base hood off the base frame. 3. Remove the two hex washer head screws and washers connecting the pump pedal link to the foot end pump pedal assembly and pump connecting rod. 4. Remove the foot end release rod from the release valve on the jack assembly by dislodging the release pedal swivel from the pins on the release pedal weldment. 5. Dislodge the jack pump piston from the pump connecting rod. 6. Remove the two hex washer head screws holding the reservoir clamp. 7. Remove the jack assembly. 8. Reverse steps 1−7 to install the new jack. NOTE The jack descent rate is preset at the factory and adjustment is not recommended.
Return to Table of Contents
15
Service Information GATCH RELEASE HANDLE REPLACEMENT Required Tools:
Needle Nose Pliers
1. Twist off the Gatch release handle knob. 2. Using needle nose pliers, remove the cotter pin holding the Gatch release rod to the Gatch release link. 3. Pull out the handle release rod. 4. Reverse to install the new Gatch release handle assembly.
GATCH VALVE BODY REPLACEMENT Required Tools: 1/2” Socket
3/8” Drive Ratchet
Needle Nose Pliers
1. Using needle nose pliers, remove the rue clip and clevis pin connecting the Gatch pump ram to the pump handle. 2. Using a 3/8” drive ratchet and a 1/2” socket, remove the three hex head bolts holding the Gatch valve body to the Gatch weldment and the lock nut holding the release link. Carefully lower the valve body out of the weldment. 3. Using needle nose pliers, remove the two rue clips and two clevis pins connecting the hydraulic cylinder to the seat section and the thigh section. Remove the valve body assembly. 4. Reverse to install the new Gatch valve body assembly.
SIDERAIL ASSEMBLY REMOVAL AND REPLACEMENT Required Tools: 1/2” Socket
3/8” Drive Ratchet
Torque Wrench
1. Raise the Fowler. Remove the slider board from the storage tray. 2. Pull up on the monitor/utility tray to remove it from the litter frame. 3. If you’re replacing the left siderail assembly, use a 1/2” socket and 3/8” drive ratchet, remove the four hex head cap screws holding the O2 holder bracket to the litter frame and remove the O2 holder. 4. Remove the four hex head cap screws holding the slider board tray to the litter frame. 5. Remove the rue ring cotter holding the Fowler pivot bolt and remove the pivot bolt. 6. Remove the two bolts holding the frame tie weldment. 7. Remove the plastic litter corner covers (see page 18). 8. Remove the two bolts holding the Fowler drop seat bracket. 9. Remove the six bolts holding the siderail to the head end and foot end litter weldments. 10. Carefully remove the siderail assembly.
Return to Table of Contents
16
Service Information SIDERAIL ASSEMBLY REMOVAL AND REPLACEMENT (CONTINUED) 11. Slide the side of the stretcher with the remaining siderail next to a wall to brace it or support it with bungee cords before starting to install the new siderail. 12. Lift the new siderail into position. 13. Insert the foot end jack support into the hole in the support tube bracket on the siderail. Insert the head end jack support tube into the slot in the Trend slide block. 14. Install the three bolts at the foot end litter weldment. Tighten to 13 foot−pounds torque. 15. Install the two bolts at the frame tie weldment. 16. Install the three bolts at the head end litter weldment. 17. Install the two bolts at the Fowler drop seat bracket. Tighten to 13 foot−pounds torque. 18. Install the litter corner covers, the slider board tray, the O2 holder and the monitor tray.
SIDERAIL LATCH REPLACEMENT Required Tools: 3/8” Drive Ratchet
T40 Torx Bit
1. Using the foot pedal, raise the litter to maximum height. 2. Remove the two bolts (A) holding the siderail latch (B) to the litter frame and discard the bolts and latch. 3. Using the new bolts provided in the kit, install the new siderail latch. 4. Verify proper latching and unlatching of the siderail before returning the stretcher to service.
Return to Table of Contents
17
Service Information PNEUMATIC CYLINDER REPLACEMENT Required Tools: 3/8” Drive Ratchet
3/8” Socket
Needle Nose Pliers
1. Using a 3/8 drive ratchet and 3/8” socket, remove the bolt connecting the pneumatic cylinder to the Fowler weldment. Save the bushing and spacers to use with the new cylinder. 2. Turn the cylinder counterclockwise to thread it out of the gas spring trip on the litter frame tie weldment. 3. Pull the Fowler cable off the gas spring trip. 4. Using needle nose pliers, pull off the rue ring cotter and remove the clevis pin holding the gas spring trip to the litter frame tie weldment. 5. Depress the new cylinder fully. 6. Thread the cylinder into the gas spring trip until it stops. CAUTION Do not use a wrench, pliers, etc. to grip the cylinder. Gripping the cylinder too tightly may mar the surface of the cylinder and cause damage. NOTE When reinstalling the bolt and the clevis pin, use the holes in each bracket nearest the foot end of the stretcher for a drop seat Fowler and the holes in each bracket nearest the head end of the stretcher for a standard Fowler. 7. Replace the bolt, bushing and spacers holding the cylinder to the Fowler weldment. The bolt will only thread through the bracket from the patient right side. 8. Lift the Fowler slightly until the parts are aligned and replace the clevis pin and the rue ring cotter to connect the gas spring trip to the litter frame tie weldment. 9. Reconnect the Fowler cable.
LITTER CORNER COVER REPLACEMENT Required Tools: Drill w/ 1/4” Bit
T25 Torx
Utility Knife
1. Drill out the rivet holding the IV pole and/or push handle in the socket and remove the IV pole/handle from the socket. 2. Using a utility knife, pry off the three hole plugs in the top of the cover. 3. Using a T25 Torx, remove the 3 screws holding the top and bottom covers together and pull apart the cover. 4. Reverse to install the new cover.
Return to Table of Contents
18
Service Information IV POLE REPLACEMENT Required Tools: T25 Torx 3/8” Drive Ratchet
Utility Knife
1/2” Socket
1. Using a utility knife, pry off the three hole plugs in the top of the litter corner cover. 2. Using a T25 Torx, remove the 3 screws holding the top and bottom covers together and pull apart the cover. 3. Remove the bolt holding the IV pole socket to the litter frame and remove the IV pole. 4. Reverse to install the new IV pole and reinstall the litter corner cover.
OXYGEN BOTTLE HOLDER REPLACEMENT Required Tools: 3/8” Drive Ratchet
1/2” Socket
1. Using the foot pedal, raise the litter to maximum height. Raise the Fowler to 90 degrees. 2. Remove the 3 bolts (A) holding the O2 bottle bracket (B) to the litter frame on the patient’s left side and discard the bolts and bottle holder assembly. 3. Use the 3 bolts provided in the kit to attach the new bottle holder assembly to the litter frame.
Return to Table of Contents
19