Sartorius Weighing Technology

L 220 S , L 440 D , L420 P and L 610 D Installation and Operating Instructions

Installation and Operating Instructions

16 Pages

File Type: PDF

File Size: 323 KB

File Name: Sartorius Weighing Technology - L 220 S, L 440 D, L420 P and L 610 D Installation and Operating Instructions.pdf

Preview

Page 1

Sartorius laboratory. L 220 S, L 420 D, L 420 P, L 420 S, L 610 D.

Electronic Toploader Installation and operating instructions

Draft protection lid

Unlocking switch

Glass cylinder

Tare bar

Pan

CAL button

Draft protection base plate

ON/OFF-Taste

Pan receptacle

Weight display

Power connection socket

Manufacturer’s label

Leveling screw

Level indicator

Sartorius laboratory. L 220 S, L 420 D, L420 P, L 420 S, L 610 D. With this Sartorius Balance you have acquired a sophisticated, top-of-the-line electronic weighing instrument that will help ease your dally work load. Please read these installation and operating instructions carefully before operating your new balance.

Pursuant to the German Directive for the Implementation of Regulations for Prevention of Accidents "Elektrische Anlagen und Betriebsmittel (VBG 4)" [Electrical Installations and Equipment] of April 1986, it is hereby certified that the equipment delivered, "electronic precision balance, model L 220 S, L 420 D, L 420 P, L 420 S or L 610 D," is manufactured and tested in compliance with the following DIN/VDE regulations DIN IEC 348/VDE 0411: Safety requirements for electronic measuring apparatus DIN IEC 380/VDE 0806: Safety of electrically energized Office machines DIN IEC 601/VDE 0750: Safety of medical electrical equipment When you use electrical equipment in installations and under ambient conditions requiring higher safety Standards, you must comply with the provisions as specified in the applicable regulations for installation in your country.

Contents

Equipment Supplied

Installation Instructions

Startup

Operation

Calibration

Balance Operating Program

Accessories (Options)

Technical Data

Equipment Supplied Do not miss out on the benefits of our full warranty. Please fill out the warranty card, indicating the date of installation, and return the card to your Sartorius dealer. The equipment supplied comprises the components shown on the left.

Save the packaging material and the box for shipping your balance to prevent any damage caused during transportation.

Installation Instructions Choose a suitable place to set up your balance. lt should not be exposed to the following: - heat radiation - aggressive/corrosive substances - vibrations - drafts. Your Sartorius Balance will provide accurate readouts even when it is exposed to unfavorable conditions. You can adapt it to your requirements simply by changing the menu code settings of the balance operating program. For this purpose, please read pages 10 through 12. After you have plugged in your balance using the AC adapter, allow for at least 30 minutes' warmup. Important Note Unplug the AC adapter before you connect or disconnect peripherals.

Startup Attach the dust cover by pressing down on the adhesive disks, and install components (5 - 1) on the balance one at a time in the order indicated. Your balance is powered by an AC adapter. Please make sure that the voltage rating printed on this unit is identical to your local line voltage rating.

Plug the AC adapter cord into the power receptacle of the balance. Secure the connection by tightening the knurled collar. Now plug the AC adapter into a wall outlet.

At the point of use, level the balance using the leveling feet (7) so that the air bubble is centered within the circle ofthe level indicator (14) (for modeis L 220 S, L 420 P and L 420 S only).

Operation The weight display shows the following special Status messages for your information: BUSY The processor is still busy processing a function and will not accept any other commands to perform functions at this time. STANDBY The balance has been turned off with the ON/OFF key (11) and is now in the STANDBY mode and ready to operate without warmup. POWER OFF The balance was disconnected from line power (reconnection to power, power failure). CAL The calibration function has been activated. In addition to grams, this balance gives you a variety of other international weight unit options to work with. Select the weight unit you need from the table of the menu options for the balance operating program, and set the appropriate code as described in the section "Balance Operating Program."

Press the ON/OFF key (11) to switch the balance on or off. You can also turn on the balance with the tare control (9). After the balance has been plugged into the AC adapter, the weight display will go out whenever you turn off the balance. All other electronic circuits will remain energized (STANDBY state). This means the balance is immediately ready to operate without requiring warmup the next time you switch it on.

After the power is tumed on, a test of all essential functions is run automatically. The self-test ends with the readout 0.00 g (if the factory code setting 5 1 1 is used). Now place your sample or object on the pan (3) to determine the weight. Read off the weight in the display (12) as soon as the weight unit (in this case "g") appears äs the stability symbol.

lf you wish to use a Container to weigh or if the weight display does not indicate 0.00 g (or the equivalent with the weight unit of your choice), press the tare control to zero the display.

Calibration Internal Calibration: (only for the L 220 S, and L 420 S) Clear the pan and zero the display. As soon as the display indicates 0.000 g, press the CAL key (10). "C" will now be displayed. lf "CE" is displayed instead, zero the display by pressing the tare control and press the CAL key again.

After a few seconds, the display will indicate "CC" followed by 0.000 g. An acoustic Signal indicates the end of the calibration procedure.

External Calibration: - This is only possible with an accurate calibration weight (L 220 S-200 g; L 420 P, L 420 S-400 g; L 610 D-500 g) Clear the pan and press the tare control (9) for at least three seconds until the calibration weight readout appears in the display. Center the calibration weight on the pan. Now the weight unit symbol is displayed. An acoustic signal indicates the end of the calibration procedure. You can. block access to the internal and external calibration functions - to find these menu codes, refer to the "Balance Operating Program." (These functions are accessible whenever the balance operating program is unlocked using the menu access switch).

Balance Operating Program The balance operating program lets you adapt your balance to various ambient conditions and to different weighing requirements, and select the weight unit(s) commonly used in your country. At the factory, we have set the codes for a Standard program, which is protected by a locking function to prevent accidental changes. The "menu code" contains the information of the operating program, lt consists of three digits, known as the page (1st digit), the line (2nd digit) and the word (3rd digit) in "computerese." How to access the menu of the balance operating program: With the balance turned off (STANDBY state), hold down the tare control (8) and briefly press the ON/OFF key (11). Upon completion of the automatic self-test, release the tare control as soon as "CH5" is displayed. The Status of the balance operating program will appear in the weight display: "L" Stands for the list mode. In this mode, you can check the menu code settings, but you cannot program new menu codes. lf you wish to change a program menu code, you must first unlock the menu access switch to access the program menu.

To do so, remove the protective cap located on the front right of your balance and slide the menu access switch (8) in the direction of the arrow. The display will indicate "C," which Stands for the change mode, meaning you can now change the menu code settings.

After you have accessed the menu of the operating program, the display will show a continuous sequence of numbers from 05 for the "page" or first digit of the code, in addition to the Status code letter "L" or "C." When the first digit of the code you wish to check or change appears, press the tare control (14). The "page" code number (1st digit) now stops in the display, and a series of numbers for the 2nd digit or "line" will begin to cycle. Press the tare control again to stop the code number of your choice in the display. Next, the numbers for the "word" (last digit) will cycle in the display. Repeat the procedure to enter the last digit of the code. The "o" symbol that appears indicates the actual setting. To change any menu code settings ("C" mode), press the tare control as soon as the appropriate numeric code is displayed. Brief display of BUSY and the "o" symbol confirms your selection, followed by a return to "zero" for the 2nd digit or "line." How to return to the weighing mode: press the tare control each time a 0 appears in the numerical sequence (word, line, page). lf you have changed a menu code, your code entry will be stored as soon as the display returns to the weighing mode. Lock the balance operating program using the menu access switch ("L" readout) and replace the protective cap.

Auto Zero This balance has an automatic zero tracking function known as "Auto Zero" (can be turned off by menu code). Any change off zero ≤ 1 digit per second will be set to zero automatically.

C 1 3 1 page

line

word

Menu of the Balance Operating Program (Active Parameters)

Code

C 1 1 C 1 1 C 1 1 C 1 1

1 2 3 4

Code

C 1 2 C 1 2 C 1 2 C 1 2 C 1 2 C 1 2 C 1 2 C 1 2 C 1 2

Stable Unstable Very unstable

1 2 3 4 5 6 7 8 9

Stability Range 0,25 digit 0,5 digit 1 digit 2 digits 4 digits 8 digits 16 digits 32 digits 64 digits

1 2 3 4

Display Format Last decimal ON Last decimal OFF Last decimal at stability All decimals at stability

Code

C 1 3 C 1 3 C 1 3 C 1 3

Ambient Conditions Very stable

Code

C 1 4 1 C 1 4 2 Code

C 1 5 1 C 1 5 2 Code

C 1 6 21 C 1 6 2

Tare Parameter Without stability At stability

Code

Internal Calibration

C 1 7 1 C 1 7 2

Accessible Access blocked

Special Information Code Program Lock OFF C 4 1 1 ON C 4 1 2 Code !

Auto Zero ON OFF

External Calibration Accessible Access blocked

Acoustic Signal ON OFF

C 4 3 1 C 4 3 2 Weight Units

Code C 5 1 C 5 1 c 5 1 c 5 1 c 5 1 c 5 1 C 5 1 c 5 2 c 5 2 c 5 2 c 5 2 c 5 2 c 5 2 C 5 2 C 5 2

1 2 3 4 5 6 7 1 2 3 4 5 6 7 8

!" " " !" "

Grams Kilograms Carats Pounds Ounces Troy ounces Parts/pound Hong Kong taels Singapur taels Taiwan taels Grains Pennyweights Mommes Milligrams Karats

g kg ct lb oz ozt o tl tl tl gr dwt o o o

C 5 2 0 C 5 0

Call program line Call program page

C 0

End of programming

Additional Parameters for the data Output format at the interface port and for calculation programs are available on request.-Please refer to the “Accessories." 1) You can choose any weight unit as long as it can be displayed in the particular weighing range you selected (for example do not set the code for "kg" when you are using a 0.1 mg balance).

Accessories (Options) Data printer, with date/time and statistics functions Print speed, approx. lines/sec. Printer housing (W x D x H) in mm

Calibration weights for: L 420 D L 420 P (4 x 100 g) L 610 D (1 x 500 g) Interface "PLUS" Performance Package, integratable (incl. interface) Over/under check weighing/ sorting & classification Mass unit conversion Weight of residue in %/change in % Statistics - Net total/ formulation & compounding Filling toward "0" - Parts counting Animal weighing Calculations by a factor Calculation of the weight per unit area/division Accumulator memory - I.D. no. memory Communication with Computers Thermo Control infrared dryer, programmable Remote display (can be plugged into the interface port of the balance) LCD, reflective for overhead projectors, transmissive Extra-large special draft shield Carrying case Antiheft locking device Dust cover

YDP02-OD 1.5 150 x 138 x 43

7072 04 7072 16 YDO 01 L YDO 01 L+

YTC 01 L

7371 01 A 7371 02 A YDS 01 L YDB 02 L 6087 69 60L220

Technical data Model

L 220 S

L 420 D

Weighing range

222

40/424

Readability

0.001

0.001/0.01

Tare range (by subtraction)

-222

-424

Standard deviation

≤± 0.001

≤± 0.001/0.005

Max. linearity deviation

≤± 0.0015

≤± 0.001/0.01

Stabilization time (typical)

Display update rate s Adaption to ambient conditions and application requirements Stability range d Ambient temperature range Sensitivity drift within 283 … 303 K Pan dimensions

0.1 ... 0.8 (selectable) by selection of one of four digital filter levels 0,25 ... 64 (selectable)

+273 ... +313

≤± 5∙10

Ø130 (approx. 5.1 in.)

-6

Clearance above pan

50 (approx. 2 in.)

Weighing chamber (Ø and H) Balance housing (W x D x H) (without draft shield) Net weight, ca. Power requirements (voltage; frequency: 50 – 60 Hz Power consumption Interface (optional)

148 and 60 (5.8 and 2.4 in.) 220 x 235 x 60 (height incl. draft protection = 127 mm or 5 in.) 4,5 (9.9lbs) 100/120 V or 220/240 V, depending on the power supply unit (adapter) used 7 (typical) RS 232 C/V24 – 28, RS 423/V10; 7-bit; parity: even, mark, odd, space; transmission rates: 150 ... 9600 Baud

mm kg

Technical data Model

L 420 P

L 420 S

L 610 D

Weighing range

80/160/424

424

60/606

Readability

0.001/0.002/0.005

0.001

0.001/0.01

Tare range (by subtraction)

-424

-606

Standard deviation

≤± 0.001/0.001/0.0025

≤± 0.001

≤± 0.001/0.005

Max. linearity deviation

≤± 0.0015/0.002/0.005

≤± 0.002

≤± 0.001/0.01

Stabilization time (typical)

Display update rate s Adaption to ambient conditions and application requirements Stability range d Ambient temperature range Sensitivity drift within 283 … 303 K Pan dimensions

2 0.1 ... 0.8 (selectable) by selection of one of four digital filter levels 0.25 ... 64 (selectable)

+273 ... +313

≤± 5∙10

Ø130 (approx. 5.1 in.)

-6

Clearance above pan

50 (approx. 2 in.)

Weighing chamber (Ø and H) Balance housing (W x D x H) (without draft shield) Net weight, ca. Power requirements (voltage; frequency: 50 – 60 Hz Power consumption Interface (optional)

mm kg

Sartorius AG B P T

37070 Göttingen Weender Landstraße 94–108, 37075 Göttingen (0551) 308-0, F (0551) 308-3289

Internet: http://www.sartorius.com Copyright by Sartorius AG, Göttingen, Deutschland. All rights reserved. No part of this publication may be printed or translated in any form or by any means without the prior written permission of Sartorius AG. Sartorius AG reserves the right to make change to the technology, features, specification and design of the equipment without notice.

Previous Page Next Page