SONY
UP-D897 Instructions for Use (4)
Instructions for Use
22 Pages

Preview
Page 1
2-345-260-11 (4)
Digital Graphic Printer Instructions for Use
UP-D897 © 2005 Sony Corporation
Owner's Record
For the customers in Canada
The model and serial numbers are located at the rear. Record these numbers in the space provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product.
This unit has been certified according to Standard CSA C22.2 No.601.1.
Model No. ____________________ Serial No. ____________________
WARNING To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
For the customers in the U.S.A. and Canada Model UP-D897 is Non-Patient Equipment. This unit can not be used in the vicinity of patients. * Patient Vicinity m 83 t) e fe (6
1.
R
To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. THIS APPARATUS MUST BE EARTHED. To disconnect the main power, unplug the AC IN connector.
This symbol indicates the equipotential terminal which brings the various parts of a system to the same potential.
For the customers in the U.S.A. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. All interface cables used to connect peripherals must be shielded in order to comply with the limits for a digital device pursuant to Subpart B of Part 15 of FCC Rules.
2
Important safeguards/notices for use in the medical environments 1. All the equipments connected to this unit shall be certified according to Standard IEC60601-1, IEC60950-1, IEC60065 or other IEC/ISO Standards applicable to the equipments. 2. When this unit is used together with other equipment in the patient area*, the equipment shall be either powered by an isolation transformer or connected via an additional protective earth terminal to system ground unless it is certified according to Standard IEC60601-1. * Patient Area 5m
1.
R
3. The leakage current could increase when connected to other equipment. 4. This equipment generates, uses, and can radiate radio frequency energy. If it is not installed and used in accordance with the instruction manual, it may cause interference to other equipment. If this unit causes interference (which can be determined by unplugging the power cord from the unit), try these measures: Relocate the unit with respect to the susceptible equipment. Plug this unit and the susceptible equipment into different branch circuit.
Consult your dealer. (According to standard EN60601-1-2 and CISPR11, Class B, Group 1) Caution When you dispose of the unit or accessories, you must obey the law in the relative area or country and the regulation in the relative hospital.
Warning on power connection Use a proper power cord for your local power supply. 1. Use the approved Power Cord (3-core mains lead) / Appliance Connector / Plug with earthing-contacts that conforms to the safety regulations of each country if applicable. 2. Use the Power Cord (3-core mains lead) / Appliance Connector /Plug conforming to the proper ratings (Voltage, Ampere). If you have questions on the use of the above Power Cord/Appliance Connector/Plug, please consult a qualified service personnel.
Warning on power connection for medical use Please use the following power supply cord. With connectors (plug or female) and cord types other than those indicated in this table, use the power supply cord that is approved for use in your area. United States
Canada
Plug Type
HOSPITAL GRADE*
HOSPITAL GRADE*
Female end
E62405, E35708
LR53182, LL022442, LL088408
Cord type
E159216, E35496 Min.Type SJT Min.18 AWG
LL112007-1, LL20262, LL32121, LL84494 Min.Type SJT Min.18AWG
Minimum cord set rating
10A/125V
10A/125V
Safety approval
UL Listed
CSA
*Note: Grounding reliability can only be achieved when the equipment is connected to an equivalent receptacle marked ‘Hospital Only’ or ‘Hospital Grade’.
3
Table of Contents Getting Started Overview ... 5 Location and Function of Parts and Controls ... 5 Front Panel ... 5 Rear Panel ... 6 Connections ... 6 Connecting to the USB Connector ... 6 Installing the Printer Driver ... 6 Paper ... 7 Paper You Can Use ... 7 Loading Paper in the Unit ... 7 Loading Paper ... 7
Operation Adjustments and Settings Using the Menu ... 9 Menu Flow ... 9 Menu List ... 10 Basic Menu Operations ... 11 Registering Menu Settings ... 13 Printing the Menu List ... 13 Printing ... 14 Starting a Print Job ... 14 Cancelling a Print Job ... 14 Making Copies of the Last Printout ... 14 Feeding Paper ... 14 Adjusting the Contrast and Brightness ... 15
Others Precautions ... 16 On Safety ... 16 On the Printer Carriage ... 16 On Installation ... 16 Maintenance ... 17 Cleaning the Cabinet ... 17 Cleaning the Thermal Head ... 17 Cleaning the Platen Roller ... 17 Specifications ... 18 Troubleshooting ... 19 Error Messages ... 20 Index ... 21
4
Getting Started
Quiet, High Quality, Fast Printing • Employs a thin thermal head with a built-in high speed drive IC, capable of high resolution images of 12.8 dots/mm. • Print speeds of approximately 1 high quality image (960 × 1280 dots) every 2 seconds when printing at high speed. • Standard image memory capable of handling and printing images up to 4096 × 1280 dots (approx. 320 × 100mm). • Monochrome printing with up to 256 shades of gradation. • Built-in temperature correction circuits prevent temperature changes which could cause blurred prints.
For more details, see the referenced page numbers enclosed in parentheses ( ).
Getting Started
Overview
Location and Function of Parts and Controls
Front Panel
USB interface The unit is equipped with a USB connector which complies with the Hi-Speed USB (USB 2.0). Easy printer settings using a menu You can make up the settings to meet your requirements using a menu. You can store up to three settings as a set of user settings. Easy Paper Loading Free access to the door panel allows you to drop paper into the unit for easy loading.
A !Power ON/OFF Switch (7, 11, 14, 17) Press to switch to ON to turn the power on. The back light on the LCD lights in green. B Printer window display (LCD: liquid crystal display) (9, 14) The back light lights in green when the unit operates normally. Also, in normal operation, the paper currently selected is indicated by the pointer on the LCD. For detailed information on the paper, see “Paper” on page 7 and “Paper currently selected” on page 14. If an error occurs, a corresponding alarm message is displayed. During menu operations, menu items and settings are displayed C Jog dial (11, 17) Used to make menu operations. D CONTR (contrast) control (15) Adjusts the contrast of the printouts. E BRIGHT (brightness) control (15) Adjusts the brightness of the printouts. F RECEIVING indicator Lights while the unit is receiving print data from the computer.
Overview / Location and Function of Parts and Controls
5
G
H Getting Started
I
FEED button (8, 14) Hold down to feed paper. While a print job is in progress, press to cancel the print job. COPY button (14) Prints another copy of the previous printout. You can make only one copy each time you press this button regardless of the print quantity set using the menu. OPEN button (8, 14) Press to open the paper door. While a print job is in progress, press to cancel the print job.
J Paper cutter Cuts the paper as each image is printed.
Rear Panel
Connections After connecting the USB connecting cable (supplied) to the unit and the computer, connect the power cord. For details about the unit connection, refer to the manuals for the computer or other peripheral devices. Notes
• Before connecting the unit to the computer, turn off the unit, computer, monitor, and all peripheral devices connected to the computer. • Before connecting the unit to the computer, disconnect the power cord from the unit. Connect the power cord to the unit only after connecting the unit and the computer. • Follow the connection procedures described in the computer manual. • Make sure that the cables are connected securely at both ends. • The unit drive software provided with the unit is not suitable for using the unit connected to a network. • Printer operation is not guaranteed when connecting to the computer using the USB cable via a hub.
Connecting to the USB Connector UP-D897
to
A
B
USB connector (6) Connects to a computer equipped with the USB interface (which conforms to USB 2.0), using the supplied USB cable.
USB connecting cable (supplied)
Equipotential ground terminal connector Used to connect to the equipotential plug to bring the various parts of a system to the same potential. Refer to “Important safeguards/notices for use in the medical environments” on page 2.
C - AC IN connector Use a proper power cord for your local power supply (not supplied). Refer to “Warning on power connection” on page 3 and “Warning on power connection for medical use” on page 3.
6
(USB) connector
Connections
Installing the Printer Driver Install the printer driver provided with the printer. For detailed instructions about how to install the unit driver, refer to the Readme.txt file included on the supplied CDROM disc.
Paper
Paper You Can Use Print paper characteristics are as follows. Print Characteristics
Paper Type
TYPE I (Normal)
UPP-110S
TYPE II (High Density)
UPP-110HD
TYPE V (High Glossy)
UPP-110HG
Notes on storing and handling paper
Getting Started
Use only Sony UPP-110S/110HD/110HG paper designed for use with this unit. High print quality cannot be guaranteed if any other paper is used with this unit, and such paper could damage the unit. You cannot use the UPP-110HA as specified for the UP-D890/890 series printer.
Loading Paper in the Unit Notes
• Before loading paper in the unit, see “Notes on storing and handling paper” (page 7). • Always handle paper carefully when loading to avoid adversely affecting the quality of the printouts. Never bend or crease the paper and never touch the printing surface with your fingers. Fingerprints perspiration can blur printing. • Do not use any paper other than UPP-110S/110HD/ 110HG paper. (page 7) • Be sure to set the “MEDIA” of the menu to the paper to be used. (page 10) You can confirm the media currently selected on the LCD. For detailed information on how to confirm, see “Paper currently selected” on page 14.
Storing unused paper • Store unused paper at a temperature below 30°C (86°F) in a dry location that is not exposed to direct sunlight. • Do not store unused paper near volatile liquids or allow the paper to contact any organic volatile liquid, cellophane tape, or any compound of vinyl chloride.
Loading Paper
Loading paper • Handle the paper carefully when loading to avoid touching the printing surface with your fingers. Perspiration or oil from you hands could cause pictures to blur. • After removing the label from the leading edge of the paper, pull the paper out 15~20 cm (about 6~8 in.) before printing. Label adhesive remaining on the paper could spoil a picture.
1
Caution
A paper cutter is mounted with the unit. When loading paper, be careful not to touch the paper cutter. Touching the paper cutter may cause injury. Press the power ON/OFF switch to turn the unit on. When paper is not loaded yet, the back light on the LCD lights in umber and the message “EMPTY” is displayed.
Storing printouts • To prevent printouts from fading or changing color, store them in a cool, dry location where the temperature is not higher than 30°C (86°F). • Store printouts in a polypropylene pouch or between sheets of paper that contain no plastic. • Do not store printouts where they will be exposed to direct sunlight or high humidity. • Do not store printouts near volatile liquids or allow the prints to contact any organic volatile liquid, cellophane tape, or any compound of vinyl chloride. • To prevent fading, do not stack printouts on or under a diazo copy sheet. • To mount printouts on another sheet of paper, use double-sides tape or a water base adhesive. • Do not incinerate waste printer paper.
Paper / Loading Paper in the Unit
7
2
Press the OPEN button to open the paper door.
Getting Started
Make sure that the paper is set straight.
4 3
Close the paper door and press on it to shut it.
Remove the label from the leading edge of the paper, pull out about 15~20 cm (about 6~8 in.) of the paper, and then set the paper roll in the paper tray. Note
To avoid exposing the paper to dust, dirt, etc. always handle it carefully when removing from its package and loading it in the unit. Paper exposed to dirt or dust cannot be used for printing.
Remove label and pull out 15 to 20 cm (about 6 to 8 inches).
Load the paper with the printing side (heat sensitive side) up. Printing is not possible if the paper is reversed.
Notes
• Make sure that the paper is loaded straight. If it is skewed, this could cause the paper to jam. • If you did not pull out enough paper in step 3, press the FEED button on the operation panel to feed some more paper out of the unit without pulling out the paper.
8
Loading Paper in the Unit
Operation
You can set up the unit according to its intended purpose, connected equipments or your individual preferences. You can store up to three settings as a set of user settings.
Adjustments and Settings Using the Menu Operation
You can carry out adjustments and settings to meet your requirements. Those settings and adjustments are retained even if the unit is turned off.
Menu Flow The contents displayed on the LCD changes in sequence as you turn the jog dial as shown in the following menu
flow chart, and you can make the settings for each menu item.
Adjustments and Settings Using the Menu
9
Menu List This section describes the menus displayed as you turn the jog dial. The setting surrounded by indicates the factory setting. Function
BEEP
To select whether BE: OFF: The operation the operation and tone does not sound. error tones sound [BE: ON]: The operation and error tones sound. BACK: Cancels the setting change and returns to the item selection column.
Operation
Item
CLEAN
COMD
10
To start head cleaning
To select the printer driver to be used
Settings
[CL: OK]: Starts the head cleaning. Be sure to use the supplied cleaning sheet. BACK: Cancels the head cleaning and returns to the item selection column. CO:895: UP-D895 driver conversion mode. Uses the printer driver for the UPD895. [CO:897]: Uses the printer driver for the UP-D897. BACK: Cancels the setting change and returns to the item selection column.
DIR a)
To select whether the top or bottom of the screen is to be printed first
DI: REV: Starts to print in the reverse direction (from the top of the screen). [DI: NOR]: Starts to print in the normal direction (from the bottom of the screen). BACK: Cancels the setting change and returns to the item selection column.
FEED
To select the paper feed method to be used after printing
FE: OFF: Feeds less paper between prints to conserve paper, or when printing multiple pictures on the same sheet. More pictures can be printed on one sheet, but because there is so little space between printed picture, feed the desired length of the paper to leave a margin using the FEED button, before cutting the paper. [FE: ON]: Feeds extra blank paper between prints. BACK: Cancels the setting change and returns to the item selection column.
Adjustments and Settings Using the Menu
Item
Function
GAMMA b)
To select the tone GA:4: TONE 4 Softest (density gradation gradation) GA:3: TONE 3 Hard gradation [GA:2]: TONE 2 Standard GA:1: TONE 1 Soft gradation BACK: Cancels the setting change and returns to the item selection column.
(When “ME:S” is selected in “MEDIA,” GAMMA is fixed to TONE 1.)
Settings
IMAGE
To set the printout to either positive printout or negative printout
IM:NEG: Makes negative printouts. [IM:POS]: Makes normal printouts. BACK: Cancels the setting change and returns to the item selection column.
INFO
To select whether or not the print conditions (such as contrast, bright, gammas and sharpness information) are printed under the image
IF:ON: Prints the information. [IF:OFF]: Does not print the information. BACK: Cancels the setting change and returns to the item selection column.
LOAD
To load the LO:3: Loads the “SA:3” registered settings settings registered using the “SAVE” menu item. LO:2: Loads the “SA:2” settings registered using the “SAVE" menu item. [LO:1]: Loads the “SA:1” settings registered using the “SAVE” menu item BACK: Cancels the setting change and returns to the item selection column.
MEDIA
To select the type ME:S: Uses the UPP-110S. of paper ME:HD: Uses the UPP110HD. [ME: HG]: Uses the UPP110HG BACK: Cancels the setting change and returns to the item selection column.
MENU
To print the menu [ME:OK]: Prints the menu settings currently list currently set. selected BACK: Cancels printing and goes back to its item column.
QTY b)
To set the print quantity between 1 and 255
You can make one to 255 copies of the same printout. [QT: 1]: Makes one sheet of the printout. BACK: Cancels the setting change and returns to the item selection column.
Function
RSIZE b)
To select whether [RS:OFF]: Prints the image or not the image at the original size. is enlarged RS:ON: Prints the image at a larger size, according to the paper size set by the printer driver. BACK: Cancels the setting change and returns to the item selection column.
SAVE
To register up to three kinds of settings
SA:3: Registers the menu settings as No.3. SA:2: Registers the menu settings as No.2. [SA:1]: Registers the menu settings as No.1. BACK: Cancels the setting change and returns to the item selection column.
To adjust the sharpness of the printout
You can set the sharpness to any of 15 steps, from 0 to 14. At a setting of 0, the outline of the printout is not emphasized. A setting of step 2 is the factory setting. BACK: Cancels the setting change and returns to the item selection column.
SHARP b)
SIDE c)
To select the direction in which the image is to be printed
To select the SPEED printing speed (When “ME:HD” is selected in “MEDIA,” the printing speed is fixed to “SP:NOR” and this item is not displayed.)
BACK
To exit menu mode
Settings
a) The printing direction is as follows.
When DI:NOR is selected
When DI: REV is selected Operation
Item
b) These items can also be set on the printer driver side. When you place a check mark in a checkbox on the “Settings” tab of the printer driver, the settings made on the printer side are enabled. When “CO:895” is selected in “COMD,” these items are not displayed and can not be set. When “CO:897” is selected, these items are disabled since the computer sends the print command to the printer until the printer completes printing. c) The print direction of the images printed is as follows. Image displayed on the monitor
S:SIDE: Prints the image rotated by 90 degrees counterclockwise. [S:STD]: Prints the image in the same direction as that displayed on the monitor. BACK: Cancels the setting change and returns to the item selection column. Printouts
SP:NOR: Prints at the normal speed. [SP:HI]: Prints at high speed. BACK: Cancels the setting change and returns to the item selection column.
When S:STD is selected.
When S:SIDE is selected
Note When “SP:HI” is selected, the power consumption is a little higher, compared with printing at the normal speed. Display this item and then press the jog dial. The unit exits the menu mode and “READY” is displayed on the LCD.
Basic Menu Operations This section describes the basic menu operation which are common to each menu, taking “How to set the printing direction” as an example.
1
Press the power ON/OFF switch to ON to turn the unit on.
Adjustments and Settings Using the Menu
11
The back light on the LCD lights in green.
4
Press the jog dial.
LCD
Operation
2
The unit enters the mode in which you can select the printing direction. “DI:NOR,” which is the factory setting, is displayed on the LCD. “DI:NOR” is the currently selected setting. In this menu operation, you will change the setting to “DI:REV.”
Confirm that “READY” is displayed on the LCD, and press the jog dial.
5
Display “DI:REV” in the LCD by turning the jog dial up or down, and then press the jog dial.
The unit enters the menu mode. When you perform a menu operation for the first time after you purchase the unit, the top item of the “BEEP” menu is displayed. If you have performed a menu operation already, the item that you set last is displayed.
3
Display “DIR” by turning the jog dial up or down.
“DI:REV” is registered as the printing direction. Note
If about 20 seconds elapse without making any menu operation after you have displayed the menu item or setting, the display returns to “READY” on the LCD and the unit exits the menu mode. In such a case, the setting of “DIR” is not changed.
12
Adjustments and Settings Using the Menu
To cancel the setting
2
1 Display “BACK” by turning the jog dial in step 5.
Display “LOAD” by turning the jog dial, and then press the jog dial again.
3
Display the number corresponding to the desired settings, and then press the jog dial. Settings corresponding to the number selected in step 3 are loaded.
2 Press the jog dial. The display on the LCD returns to “DIR.” To continue menu operations Make settings by repeating steps 3 to 5.
1
Display “BACK” by turning the jog dial after performing the operation of step 5.
2
Press the jog dial. The display returns to “READY.” The unit exits the menu mode.
Menu lock function If the message “LOCK” is displayed and you hear the alarm sound when you press the jog dial, the jog dial is disabled because the menu operation function is locked. If you want to perform a menu operation, contact the nearest authorized dealer.
To retain previously loaded settings Example: Settings registered as “SA:1” are loaded and settings are to be changed. To retain the original settings of “SA:1” and to register the new settings as “SA:2,” proceed as follows.
1
Load the settings of “LO:1” following the procedure for loading the desired settings.
2
Change the loaded settings as required.
3
Select “SA:2” following procedure for registering the settings.
4
Press the jog dial. The settings, changed in step 2, are registered as “SA:2” (No.2).
Registering Menu Settings You can store up to three sets of settings made using the menu, and you can load the desired setting when needed. The unit retains these settings even if you turn off the power. Note
When you use the unit for the first time after you purchase it, factory settings are registered in all three of the stored selections.
Registering new settings
1
Make all of the required settings.
2
Display “SAVE” by turning the jog dial, and then press the jog dial.
3
Display the desired number by turning the jog dial, and then press the jog dial, again. The settings made in step 1 are registered in the number selected in step 3.
Loading the desired settings
Operation
To end the menu operation
When you change the loaded settings The unit operates according to the changed settings. In this case, the unit operates according to these settings until you load another set of settings, even if you turn off the unit. When you load another group of settings, the settings loaded previously are cleared.
Printing the Menu List You can make a printout of the current menu settings.
1
Press the jog dial. The menu item you changed last is displayed.
2
Display “MENU” by turning the jog dial, and then press the jog dial.
3
Display “ME:OK” by turning the jog dial and then press the jog dial. The unit starts printing the current menu settings. “MENU” is displayed on the LCD.
4
Display “BACK” by turning the jog dial, and then press the jog dial. The message “READY” is displayed on the LCD, and the unit returns to the normal printing mode.
You can load the desired settings and make printouts with the loaded settings.
1
Confirm that “READY” is displayed on the LCD, and press the jog dial.
Adjustments and Settings Using the Menu
13
In the following figure, the currently selected paper is the UPP-110S paper.
Printing Before Starting a Print Job Always check the following points: • unit connected correctly? (page 6) • Printer driver installed? (page 6) • Paper loaded correctly? (page 7) • Menu settings and menu adjustments done correctly? (page 9)
Indicates the UPP-110S Indicates the UPP-110HD Indicates the UPP-110HG
Operation
Starting a Print Job
1
Press the power ON/OFF switch to turn the unit on. The back light on the LCD lights in green, and “READY” is displayed on the LCD.
Cancelling a Print Job To cancel a print job in progress, press the OPEN button or the FEED button.
LCD
Making Copies of the Last Printout Press the COPY button. The unit makes a copy of the last printout. The image of the last printout is retained in the unit’s memory until you make a printout of another image or turn the power off. You can make only one copy regardless of the print quantity set using the menu.
2
Execute the print job with the software application. Note
When the message is displayed on the LCD If a problem occurs, the back light on the LCD lights in umber and the error message stating the problem is displayed on the LCD. Message
Cause and remedy
EMPTY
Paper is not loaded. Load paper.
DOOR
The door is open. Close the door.
When the unit stops printing during printing When printing almost black images continuously, the thermal head protection circuit may shut down the unit to prevent the thermal head from overheating. In such a case, the message “COOL” is displayed on the LCD. Leave the unit until the head cools down and this message disappears. Paper currently selected You can confirm the paper currently selected on the LCD. The pointer points to the paper currently selected.
14
Printing
If you press the COPY button immediately after turning the power on, the alarm buzzer will sound as nothing is stored in memory. To make multiple copies of the same printout Press the COPY button as many times as necessary (maximum 20 copies including the first printout) while copying the first printout. Each time you press the COPY button, a short buzzer sounds. To interrupt copying Press the OPEN or FEED button while copying.
Feeding Paper To feed paper, press the FEED button. The unit will continue to feed paper as long as you hold down the FEED button. Do not attempt to pull paper out of the unit with your hand.
Adjusting the Contrast and Brightness You can adjust the contrast and brightness of the unit using the CONTR control and BRIGHT control on the front panel.
Operation
To adjust the contrast You can adjust the contrast of printouts using the CONTR control. To make the contrast stronger: Turn the CONTR control clockwise. To make the contrast weaker: Turn the CONTR control counterclockwise. Note
The contrast adjusting function is equivalent to “Light” of the density control provided with the printer driver. The value adjusted by using this CONTR control is added to the value already set as “Light.” To adjust the brightness You can adjust the brightness of printouts using the BRIGHT control. To make the image brighter: Turn the BRIGHT control clockwise. To make the image darker: Turn the BRIGHT control counterclockwise. Note
When the menu operation function is locked, CONTR and BRIGHT controls are also disabled in addition to the jog dial. If you want to use the CONTR and BRIGHT controls, contact the nearest authorized dealer.
Printing
15
Others
ventilation holes (intake) on the left hand side and the ventilation holes (exhaust) on the rear of the cabinet.
Precautions On Safety
Others
• Check the operating voltage before operation. Operate the unit only with a power source specified in “Specifications”. • Stop operation immediately if any liquid or solid object falls into the cabinet. Unplug the unit and have it checked by qualified personnel. • Unplug the unit from the wall outlet if you will not be using it for a long time. Disconnect the power cord by grasping the plug. Never pull the cord itself. • Do not disassemble the cabinet. Refer servicing to qualified personnel only. • Connect the power plug of the unit to a wall outlet with a protective earth terminal. The safety earth should be properly established. Caution on the paper cutter A paper cutter is mounted with the unit. When loading a paper or cleaning the unit, be careful not to touch the paper cutter. Touching the paper cutter may cause injury.
On the Printer Carriage Do not carry or move the unit when the paper roll is placed in the unit. Doing so may cause a malfunction.
On Installation • Place the unit on a level and stable surface. If you use the unit with placed on an uneven surface, malfunction of the unit is likely to occur. • Do not install the unit near heat sources. Avoid locations near radiators or air ducts, or places subject to direct sunlight or excessive dust, humidity, mechanical shock or vibration. • Provide adequate air circulation to prevent heat buildup. Do not place the unit on surfaces such as rugs, blankets, etc., or near materials such as curtains and draperies. • To prevent internal heat built-up, leave enough room around the printer for air to circulate through the
16
Precautions
Ventilation holes (intake) Ventilation holes (exhaust)
• If the unit is subjected to wide and sudden changes in temperature, such as when it is moved from a cold room to a warm room or when it is left in a room with a heater that tends to produce large amounts of moisture, condensation may form inside the unit. In such cases the unit will probably not work properly, and may even develop a fault if you persist in using it. If moisture or condensation forms, turn off the power and allow the unit to stand for at least one hour.
Maintenance
3
Insert the cleaning sheet, with the black surface facing down, into the groove of the paper tray.
Insert the cleaning sheet into the groove of the paper tray.
Cleaning the Cabinet Use a wrung out damp cloth, or a damp cloth soaked in water and a mild detergent, to clean the cabinet surface. To avoid damaging the cabinet of the unit, never use alcohol, thinner, or any other type of organic solvent, or any type of abrasive cleaner, to clean the cabinet.
Cleaning sheet supplied
Cleaning the Thermal Head Others
If the printout is dirty or white stripes appear on the printouts, clean the thermal head using the cleaning sheet supplied. Carry out the head cleaning operation using the menu.
4
Close the door by pushing it.
5
A paper cutter is mounted with the unit. When cleaning the thermal head, be careful not to touch the paper cutter. Touching the paper cutter may cause injury.
Press the jog dial. The menu item changed last is displayed.
6
Display “CLEAN” by turning the jog dial, and then press the jog dial.
1
7
Confirm that “CL:OK” is displayed, and then press the jog dial. The unit starts cleaning the thermal head. “CLEAN” is displayed on the LCD. When the cleaning sheet stops and the alarm sounds, the cleaning is completed.
8
Press the OPEN button to open the door and remove the cleaning sheet.
9
Close the door by pushing it.
Note
Press the power ON/OFF switch to ON to turn the unit on.
Note
2
Press the OPEN button to open the door.
Clean the thermal head only when necessary. If you clean the thermal head too frequently, it may cause a malfunction.
Cleaning the Platen Roller If the paper cannot be ejected smoothly after printing, the platen roller may be dirty. In such a case, clean the platen roller with a soft cloth moistened with a damp clothe soaked in water and a mild detergent.
If the paper is loaded in the paper tray, remove it.
1
Press the power ON/OFF switch to ON to turn the unit on.
2
Press the OPEN button to open the door. If the paper is loaded in the paper tray, remove it.
Maintenance
17
3
Clean the platen roller gently with a damp clothe soaked in water and a mild detergent.
Platen roller
Others
Notes
• After the surface of the platen roller wiped has been dried completely, turn the platen roller to clean another portion. • Do not turn the platen roller with hands. Use the FEED button to turn it. To clean another part of the surface of the platen roller, go to the next step.
4
Press and hold down the FEED button so that the platen roller turns automatically. Release the FEED button when the surface of the platen roller to be cleaned appears.
Be careful so that you have your fingers caught in the turning platen roller.
Notes
• The platen roller is turning while you are pressing the FEED button. Be careful so that you have your fingers caught in the turning platen roller. • Be sure to start cleaning only after the platen roller has stopped completely.
18
5
Repeat steps 3 and 4 until the platen roller becomes clean.
6
After the platen roller has been dried completely, close the door by pushing it.
Specifications
Specifications Power requirement 100 to 240 V AC, 50/60 Hz Input current 1.5 A to 0.8 A Operating temperature 5 °C to 35 °C (41 °F to 95 °F) Operating humidity 20 % to 80 % Storage and transport temperature –20 °C to +60 °C (–4 °F to +140 °F) Storage and transport humidity 20 % to 90 % Dimensions 154 × 88 × 240 mm (w/h/d) (6 1/6 × 3 1/2 × 9 1/2 inches) Mass 2.6 kg (5 lb 11 oz) (printer only) Thermal head Thin-film thermal head, 1280 dots Gradation 256-level gradation (8-bit) Memory capacity 4096 × 1280 × 8 (bit) Picture size 320 × 100 mm (max.) Printing speed About 2 sec./image (960 × 1280 dots) (printing at the high speed) About 3.3 sec./image (960 × 1280 dots) (printing at the normal speed) Picture elements 4096 × 1280 dots (max.) Dot density H: 100 mm/1280 dots = 0.078 V: 100 mm/1280 dots = 0.078 Square dots
Interface Hi-Speed USB (USB 2.0) Accessories provided Thermal head cleaning sheet (1) CD-ROM (including multi-lingual operating instructions, Readme and printer driver) (1) Media label (1) USB cable 1-824-211-41 (SONY) (1) Before Using this Printer (1) Service Contact List (1) Software License (1)
Medical Specifications Protection against electric shock: Class I Protection against harmful ingress of water: Ordinary Degree of safety in the presence of flammable anesthetics or oxygen: Not suitable for use in the presence of flammable anesthetics or oxygen Mode of operation: Continuous The design and these specifications are subject to change without prior notification.
Troubleshooting Before you call for service, please check the problems and solutions described below. If you cannot solve the problem, contact the nearest authorized dealer. Causes/remedies
First few prints spotted with small dots.
New paper roll just installed? tIf a new roll of paper has just been loaded, paper dust may cause white spots in printed images. Press the FEED button and hold it down to feed about 15~20 cm (6~8 in.) and then release. (page 8)
Print job does not start.
• Paper does not feed. tPower switched on? tUnit connected correctly? tPaper roll loosen? • Alarm sounds. tPaper loaded correctly? (page 8) • Paper feeds but printing does not start. tPrinter paper loaded with the wrong side up? (page 8)
Paper Jams
• Jammed paper visible? tPress the OPEN button to open the paper door, remove the printout or the paper roll, and then gently pull the jammed paper out of the unit. • Condensation collected in unit? tIf the unit has just been brought into a warm room from a cold location, condensation may have formed inside the unit. Switch the unit off and let it set for 1 - 2 hours (until it warms to room temperature), then try printing again.
Printouts dirty.
Thermal head dirty? tUse the head cleaning sheet provided with the unit to clean the thermal head. (page 17)
The unit stops printing while printing almost black images continuously and the message “COOL” is displayed on the LCD.
When printing almost black images continuously, the thermal head protection circuit may shut down the unit to prevent the thermal head from overheating. tWait for the message to disappear.
Paper is not fed smoothly.
Platen roller dirty? tClean the platen roller. (page 17)
Troubleshooting
Others
Symptom
19
Error Messages Messages appear on the LCD under the following conditions. Take the remedial actions shown next to the messages to correct the problem. Description and remedy
DOOR
The paper door is open. tClose the paper door until it is locked securely.
EMPTY
• There is no paper loaded. • Paper has been used up. tLoad some paper. (page 7)
COOL
The protection circuit that prevents the thermal head from overheating has been activated. tWait for the message to disappear. Printing will then resume automatically.
LOCK
The menu operation function is locked. The jog dial, CONTR control and BRIGHT control are disabled. tIf you want to perform menu operations or use those controls, contact the nearest authorized dealer.
WAIT
The unit is under internal processing. tWait for a while.
Others
Messages
20
Error Messages